Hot water problem
 

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the bathroom
furthest from the hot water heater, and then only in the tub and not the
handbasin. Anytime hot water is turned on in the tub, the water runs black
then finally clears. Since it is the guest bathroom, it is something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net

Hot water problem
 

limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the bathroom
furthest from the hot water heater, and then only in the tub and not the
handbasin. Anytime hot water is turned on in the tub, the water runs black
then finally clears. Since it is the guest bathroom, it is something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net

Black water usually means a rubber faucet washer deteriorating.
But it might also be caused by corrosion of a galv iron nipple
in the supply or in the tub spout connection to the faucet.

Jim

Hot water problem
 

"Speedy Jim" wrote
limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the
bathroom
furthest from the hot water heater, and then only in the tub and not
the
handbasin. Anytime hot water is turned on in the tub, the water
runs black
then finally clears. Since it is the guest bathroom, it is
something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net

Black water usually means a rubber faucet washer deteriorating.
But it might also be caused by corrosion of a galv iron nipple
in the supply or in the tub spout connection to the faucet.

Jim

It can also be caused by a trace amount or more of sulfur (H2S gas) in
the water. The tub being used less frequently than other fixtures and
usually with the best flow rate will allow precipitation of the H2S to
cling to the inside of the tubing and then break loose from time to time
as the water is used.

Gary
Quality Water Associates

Hot water problem
 

"Speedy Jim" wrote in message
limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the
bathroom
furthest from the hot water heater, and then only in the tub and not the
handbasin. Anytime hot water is turned on in the tub, the water runs
black
then finally clears. Since it is the guest bathroom, it is something
I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net

Black water usually means a rubber faucet washer deteriorating.
But it might also be caused by corrosion of a galv iron nipple
in the supply or in the tub spout connection to the faucet.

Jim

Everything is new after our house was totally lost in a fire. There are no
galv iron nipples in the system.

Hot water problem
 

"Gary Slusser" wrote in message
limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the
bathroom
furthest from the hot water heater, and then only in the tub and not
the
handbasin. Anytime hot water is turned on in the tub, the water
runs black
then finally clears. Since it is the guest bathroom, it is
something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net


It can also be caused by a trace amount or more of sulfur (H2S gas) in
the water. The tub being used less frequently than other fixtures and
usually with the best flow rate will allow precipitation of the H2S to
cling to the inside of the tubing and then break loose from time to time
as the water is used.

Gary
Quality Water Associates

Yes, we have quite a bit of sulfur in the water. I have to drain the HW
tank every once in a while because of the odor. Also, when I run the hot
water in the bathroom in question, I don't get the sediment until the water
actually gets hot. I drained the HW tank this morning, then also got the
sediment in the jacuzzi in the room next to the tank. Is there a solution,
other than a whole water treatment system? Thanks for your reply.

Hot water problem
 

"limey" wrote

"Gary Slusser" wrote in message
limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the
bathroom
furthest from the hot water heater, and then only in the tub and
not
the
handbasin. Anytime hot water is turned on in the tub, the
water
runs black
then finally clears. Since it is the guest bathroom, it is
something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net


It can also be caused by a trace amount or more of sulfur (H2S gas)
in
the water. The tub being used less frequently than other fixtures
and
usually with the best flow rate will allow precipitation of the H2S
to
cling to the inside of the tubing and then break loose from time to
time
as the water is used.

Gary
Quality Water Associates

Yes, we have quite a bit of sulfur in the water. I have to drain the
HW
tank every once in a while because of the odor. Also, when I run the
hot
water in the bathroom in question, I don't get the sediment until the
water
actually gets hot. I drained the HW tank this morning, then also got
the
sediment in the jacuzzi in the room next to the tank. Is there a
solution,
other than a whole water treatment system? Thanks for your reply.

Actually it sounds as if you have a hot water only odor, that can be
caused by a trace of H2S in the cold but.... if there is none, then you
have a sulfate or other reducing bacteria problem and must kill them
before they get to the heater tank. Or, remove the anode rod or replace
it with other than a magnesium type but if you drop any of the old one
into the tank as you remove it - it's like ya didn't remove any of it
and you can't get pieces out of the bottom of the tank. Or, raise the
temp of the heater to 140f. Anode rods can be like real difficult to
loosen - the key is holding the tank from rotating. lol.

You can ad about a half gallon of bleach to the heater, draw chlorinated
water to all hot water fixtures and let it sit 10 minutes and turn them
on for a count of ten and wait 10 minutes and repeat for an hour. Then
let sit for as long as possible or at least a few hours and then drain
(with the power/fuel off) and flush the tank with cold water until the
last water out of the drain is as clear as you can get it. This can take
many times of flushing with about 30 seconds of cold water each time.
That's enough chlorine to burn eyes and bleach spots on clothes so no
hot water use until you're done and refilled with clean water.

No, no other way than treatment equipment if you do have cold water H2S.
It is easily treated and it isn't very expensive. Most will talk to you
about some bleach down the well. That usually doesn't work if your H2S
is naturally occurring, it can if the problem is reducing type bacteria
in the well but problem is, they're in the 'aquifer too and you can't
reach there with bleach alone. Chlorine raises the pH of the water and
chlorine is only a good disinfectant at a pH of 7.2. and lower to about
5.2. Plus shocking a well can cause serious water quality and
pump/plumbing. Also, shocking usually makes a bacteria caused problem
worse.

Gary
Quality Water Associates

Hot water problem
 

"Gary Slusser" wrote

limey wrote:
Yes, we have quite a bit of sulfur in the water. I have to drain the
HW
tank every once in a while because of the odor. Also, when I run the
hot
water in the bathroom in question, I don't get the sediment until the
water
actually gets hot. I drained the HW tank this morning, then also got
the
sediment in the jacuzzi in the room next to the tank. Is there a
solution,
other than a whole water treatment system? Thanks for your reply.

Actually it sounds as if you have a hot water only odor, that can be
caused by a trace of H2S in the cold but.... if there is none, then you
have a sulfate or other reducing bacteria problem and must kill them
before they get to the heater tank. Or, remove the anode rod or replace
it with other than a magnesium type but if you drop any of the old one
into the tank as you remove it - it's like ya didn't remove any of it
and you can't get pieces out of the bottom of the tank. Or, raise the
temp of the heater to 140f. Anode rods can be like real difficult to
loosen - the key is holding the tank from rotating. lol.

You can ad about a half gallon of bleach to the heater, draw chlorinated
water to all hot water fixtures and let it sit 10 minutes and turn them
on for a count of ten and wait 10 minutes and repeat for an hour. Then
let sit for as long as possible or at least a few hours and then drain
(with the power/fuel off) and flush the tank with cold water until the
last water out of the drain is as clear as you can get it. This can take
many times of flushing with about 30 seconds of cold water each time.
That's enough chlorine to burn eyes and bleach spots on clothes so no
hot water use until you're done and refilled with clean water.

No, no other way than treatment equipment if you do have cold water H2S.
It is easily treated and it isn't very expensive. Most will talk to you
about some bleach down the well. That usually doesn't work if your H2S
is naturally occurring, it can if the problem is reducing type bacteria
in the well but problem is, they're in the 'aquifer too and you can't
reach there with bleach alone. Chlorine raises the pH of the water and
chlorine is only a good disinfectant at a pH of 7.2. and lower to about
5.2. Plus shocking a well can cause serious water quality and
pump/plumbing. Also, shocking usually makes a bacteria caused problem
worse.

Gary
Quality Water Associates

Thank you for the great explanation. Our water is high in sulfur and in
iron. We had the odor problem for years with the previous water heater and
I would put bleach in there to kill the odor; that would take care of it
for quite a while.
Removing the anode would be quite a job, since the builder put a row of
cabinets on that wall and one sits squarely on top of the heater (with
cut-outs to accommodate the pipes). Looks like I need to discuss a water
treatment system with some local company. I agree - I don't want to shock
the well.

Thanks again, Gary - you have given me great advice.

Hot water problem
 

"limey" wrote

"Gary Slusser" wrote

limey wrote:
Yes, we have quite a bit of sulfur in the water. I have to drain
the
HW
tank every once in a while because of the odor. Also, when I run
the
hot
water in the bathroom in question, I don't get the sediment until
the
water
actually gets hot. I drained the HW tank this morning, then also
got
the
sediment in the jacuzzi in the room next to the tank. Is there a
solution,
other than a whole water treatment system? Thanks for your reply.

Actually it sounds as if you have a hot water only odor, that can be
caused by a trace of H2S in the cold but.... if there is none, then
you
have a sulfate or other reducing bacteria problem and must kill them
before they get to the heater tank. Or, remove the anode rod or
replace
it with other than a magnesium type but if you drop any of the old
one
into the tank as you remove it - it's like ya didn't remove any of
it
and you can't get pieces out of the bottom of the tank. Or, raise
the
temp of the heater to 140f. Anode rods can be like real difficult to
loosen - the key is holding the tank from rotating. lol.

You can ad about a half gallon of bleach to the heater, draw
chlorinated
water to all hot water fixtures and let it sit 10 minutes and turn
them
on for a count of ten and wait 10 minutes and repeat for an hour.
Then
let sit for as long as possible or at least a few hours and then
drain
(with the power/fuel off) and flush the tank with cold water until
the
last water out of the drain is as clear as you can get it. This can
take
many times of flushing with about 30 seconds of cold water each
time.
That's enough chlorine to burn eyes and bleach spots on clothes so
no
hot water use until you're done and refilled with clean water.

No, no other way than treatment equipment if you do have cold water
H2S.
It is easily treated and it isn't very expensive. Most will talk to
you
about some bleach down the well. That usually doesn't work if your
H2S
is naturally occurring, it can if the problem is reducing type
bacteria
in the well but problem is, they're in the 'aquifer too and you
can't
reach there with bleach alone. Chlorine raises the pH of the water
and
chlorine is only a good disinfectant at a pH of 7.2. and lower to
about
5.2. Plus shocking a well can cause serious water quality and
pump/plumbing. Also, shocking usually makes a bacteria caused
problem
worse.

Gary
Quality Water Associates

Thank you for the great explanation. Our water is high in sulfur and
in
iron. We had the odor problem for years with the previous water
heater and
I would put bleach in there to kill the odor; that would take care of
it
for quite a while.
Removing the anode would be quite a job, since the builder put a row
of
cabinets on that wall and one sits squarely on top of the heater (with
cut-outs to accommodate the pipes). Looks like I need to discuss a
water
treatment system with some local company. I agree - I don't want to
shock
the well.

Thanks again, Gary - you have given me great advice.

You sound handy enough to install something yourself. If you want a
quote and to maybe save hundreds, my email works.

Gary
Quality Water Associates

Hot water problem
 

When dealing with a delay in getting hot water, check out
www.RedyTemp.com they have a downloadable market analysis which shows
all the different hot water recirculators available. They also
explain the problems with most. Only the RedyTemp hot water
recirculator has answered the many problems apparent with most others.
Installation, hard water calcium buildup were the biggest problems
until the RedyTemp came out. These things really do work otherwise
the water companies wouldn't be given rebates for people who install
them in their home. The RedyTemps is so easy to install and
uninstall, you can take it with you if you move. We love ours.

On Mon, 10 Nov 2003 04:42:52 GMT, "Gary Slusser"
wrote:


"limey" wrote

"Gary Slusser" wrote in message
limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the
bathroom
furthest from the hot water heater, and then only in the tub and
not
the
handbasin. Anytime hot water is turned on in the tub, the
water
runs black
then finally clears. Since it is the guest bathroom, it is
something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net


It can also be caused by a trace amount or more of sulfur (H2S gas)
in
the water. The tub being used less frequently than other fixtures
and
usually with the best flow rate will allow precipitation of the H2S
to
cling to the inside of the tubing and then break loose from time to
time
as the water is used.

Gary
Quality Water Associates

Yes, we have quite a bit of sulfur in the water. I have to drain the
HW
tank every once in a while because of the odor. Also, when I run the
hot
water in the bathroom in question, I don't get the sediment until the
water
actually gets hot. I drained the HW tank this morning, then also got
the
sediment in the jacuzzi in the room next to the tank. Is there a
solution,
other than a whole water treatment system? Thanks for your reply.

Actually it sounds as if you have a hot water only odor, that can be
caused by a trace of H2S in the cold but.... if there is none, then you
have a sulfate or other reducing bacteria problem and must kill them
before they get to the heater tank. Or, remove the anode rod or replace
it with other than a magnesium type but if you drop any of the old one
into the tank as you remove it - it's like ya didn't remove any of it
and you can't get pieces out of the bottom of the tank. Or, raise the
temp of the heater to 140f. Anode rods can be like real difficult to
loosen - the key is holding the tank from rotating. lol.

You can ad about a half gallon of bleach to the heater, draw chlorinated
water to all hot water fixtures and let it sit 10 minutes and turn them
on for a count of ten and wait 10 minutes and repeat for an hour. Then
let sit for as long as possible or at least a few hours and then drain
(with the power/fuel off) and flush the tank with cold water until the
last water out of the drain is as clear as you can get it. This can take
many times of flushing with about 30 seconds of cold water each time.
That's enough chlorine to burn eyes and bleach spots on clothes so no
hot water use until you're done and refilled with clean water.

No, no other way than treatment equipment if you do have cold water H2S.
It is easily treated and it isn't very expensive. Most will talk to you
about some bleach down the well. That usually doesn't work if your H2S
is naturally occurring, it can if the problem is reducing type bacteria
in the well but problem is, they're in the 'aquifer too and you can't
reach there with bleach alone. Chlorine raises the pH of the water and
chlorine is only a good disinfectant at a pH of 7.2. and lower to about
5.2. Plus shocking a well can cause serious water quality and
pump/plumbing. Also, shocking usually makes a bacteria caused problem
worse.

Gary
Quality Water Associates

Hot water problem
 

When dealing with a delay in getting hot water, check out
www.RedyTemp.com they have a downloadable market analysis which shows
all the different hot water recirculators available. They also
explain the problems with most. Only the RedyTemp hot water
recirculator has answered the many problems apparent with most others.
Installation, hard water calcium buildup were the biggest problems
until the RedyTemp came out. These things really do work otherwise
the water companies wouldn't be given rebates for people who install
them in their home. The RedyTemps is so easy to install and
uninstall, you can take it with you if you move. We love ours.

On Mon, 10 Nov 2003 04:42:52 GMT, "Gary Slusser"
wrote:


"limey" wrote

"Gary Slusser" wrote in message
limey wrote:

Puzzle - can anyone shed light on this?
We have no problem with the hot water in the house except in the
bathroom
furthest from the hot water heater, and then only in the tub and
not
the
handbasin. Anytime hot water is turned on in the tub, the
water
runs black
then finally clears. Since it is the guest bathroom, it is
something I'd
like to solve. Any thoughts, anyone?
--


limey at toad dot net


It can also be caused by a trace amount or more of sulfur (H2S gas)
in
the water. The tub being used less frequently than other fixtures
and
usually with the best flow rate will allow precipitation of the H2S
to
cling to the inside of the tubing and then break loose from time to
time
as the water is used.

Gary
Quality Water Associates

Yes, we have quite a bit of sulfur in the water. I have to drain the
HW
tank every once in a while because of the odor. Also, when I run the
hot
water in the bathroom in question, I don't get the sediment until the
water
actually gets hot. I drained the HW tank this morning, then also got
the
sediment in the jacuzzi in the room next to the tank. Is there a
solution,
other than a whole water treatment system? Thanks for your reply.

Actually it sounds as if you have a hot water only odor, that can be
caused by a trace of H2S in the cold but.... if there is none, then you
have a sulfate or other reducing bacteria problem and must kill them
before they get to the heater tank. Or, remove the anode rod or replace
it with other than a magnesium type but if you drop any of the old one
into the tank as you remove it - it's like ya didn't remove any of it
and you can't get pieces out of the bottom of the tank. Or, raise the
temp of the heater to 140f. Anode rods can be like real difficult to
loosen - the key is holding the tank from rotating. lol.

You can ad about a half gallon of bleach to the heater, draw chlorinated
water to all hot water fixtures and let it sit 10 minutes and turn them
on for a count of ten and wait 10 minutes and repeat for an hour. Then
let sit for as long as possible or at least a few hours and then drain
(with the power/fuel off) and flush the tank with cold water until the
last water out of the drain is as clear as you can get it. This can take
many times of flushing with about 30 seconds of cold water each time.
That's enough chlorine to burn eyes and bleach spots on clothes so no
hot water use until you're done and refilled with clean water.

No, no other way than treatment equipment if you do have cold water H2S.
It is easily treated and it isn't very expensive. Most will talk to you
about some bleach down the well. That usually doesn't work if your H2S
is naturally occurring, it can if the problem is reducing type bacteria
in the well but problem is, they're in the 'aquifer too and you can't
reach there with bleach alone. Chlorine raises the pH of the water and
chlorine is only a good disinfectant at a pH of 7.2. and lower to about
5.2. Plus shocking a well can cause serious water quality and
pump/plumbing. Also, shocking usually makes a bacteria caused problem
worse.

Gary
Quality Water Associates