Installing HardiPanels - Need Suggestions
 

Our home is partially covered with a masonite, stucco-like finish siding
that is starting to degrade. I want to replace these 4 x 8 panels with
Hardipanel cedar mill sidings. Having never done this before, I'm
soliciting suggestions that anyone might have to help me do this. I'll have
to replace about 1/2 of the house---almost 32 panels. (Rest of house has
different siding and most under a porch). The rear will be the toughest.
It's two stories tall--about 8 panels up and 12 panels down. I'm going to
borrow scaffolding from a neighbor for the upstairs work.

I know I will need eye protection and mask when I cut the material. Is a 7"
rotary saw okay? I'll need to buy some kind of masonry blade I suppose.
What about nails: size, special type? Hardipanels are heavy. Does this
cause any problem when I try to hang it on existing framing?

Thanks for any suggestions you might have.

Installing HardiPanels - Need Suggestions
 

"J.V." wrote in
ink.net:

I know I will need eye protection and mask when I cut the material.
Is a 7" rotary saw okay? I'll need to buy some kind of masonry blade
I suppose. What about nails: size, special type? Hardipanels are
heavy. Does this cause any problem when I try to hang it on existing
framing?

Thanks for any suggestions you might have.




Many of your questions are addressed here (you may have to paste this
link back together):

http://www.jameshardie.com/builder/i...installation.p
hp

There are fiber cement blades for circular saws and I'd recommend one. I
had a piece to cut and tried a masonry blade with poor results. The saw
bogged down and I couldn't keep the cut straight. It may have been
technique but I had no such problems with a $15 carbide fiber cement
blade from Home Depot. Cutting with the good side down made for a
smoother cut. The dust won't be good for the saw so I wouldn't use a saw
with a lot of sentimental value because it may not survive.

I think they only problem you'll have with weight is getting the panels
into position. They are heavy and it's fairly easy to damage the edges
by banging them into stuff or break the panel by flexing it too much.
Your house would have to be in really poor structural condition for it
have any problems holding them up.

Doug

Installing HardiPanels - Need Suggestions
 

"J.V." wrote in message link.net...
Our home is partially covered with a masonite, stucco-like finish siding
that is starting to degrade. I want to replace these 4 x 8 panels with
Hardipanel cedar mill sidings. Having never done this before, I'm
soliciting suggestions that anyone might have to help me do this. I'll have
to replace about 1/2 of the house---almost 32 panels. (Rest of house has
different siding and most under a porch). The rear will be the toughest.
It's two stories tall--about 8 panels up and 12 panels down. I'm going to
borrow scaffolding from a neighbor for the upstairs work.

I know I will need eye protection and mask when I cut the material. Is a 7"
rotary saw okay? I'll need to buy some kind of masonry blade I suppose.
What about nails: size, special type? Hardipanels are heavy. Does this
cause any problem when I try to hang it on existing framing?

Thanks for any suggestions you might have.


Other resources:
Tamlyn produces accessories including starter strips.
Cemplank also produces panels.

Tom Baker

Installing HardiPanels - Need Suggestions
 

I have had problems getting nails to hold. They pop easily especially along
the edges. Good stuff otherwise. I used a short 2x2 to hold it while
nailing. I tried the masonry blade and ended up with a regular cheap carbide
blade.

M Hamlin
"Doug" wrote in message
. ..
"J.V." wrote in
ink.net:

I know I will need eye protection and mask when I cut the material.
Is a 7" rotary saw okay? I'll need to buy some kind of masonry blade
I suppose. What about nails: size, special type? Hardipanels are
heavy. Does this cause any problem when I try to hang it on existing
framing?

Thanks for any suggestions you might have.




Many of your questions are addressed here (you may have to paste this
link back together):

http://www.jameshardie.com/builder/i...installation.p
hp

There are fiber cement blades for circular saws and I'd recommend one. I
had a piece to cut and tried a masonry blade with poor results. The saw
bogged down and I couldn't keep the cut straight. It may have been
technique but I had no such problems with a $15 carbide fiber cement
blade from Home Depot. Cutting with the good side down made for a
smoother cut. The dust won't be good for the saw so I wouldn't use a saw
with a lot of sentimental value because it may not survive.

I think they only problem you'll have with weight is getting the panels
into position. They are heavy and it's fairly easy to damage the edges
by banging them into stuff or break the panel by flexing it too much.
Your house would have to be in really poor structural condition for it
have any problems holding them up.

Doug