Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#2
|
|||
|
|||
Why solder will not melt?
ississauga wrote: I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? Chances are the solder *is* melting, but the pipe/fitting is siezed together because of a *very* close fit when they were made up. This can be very annoying, as I'm sure you've found out by yourself. On occasion I've had to cut the pipe a couple of inches from the fitting so that I could crush an twist the stub with a pair of vise-grips to work it out of the fitting with the joint hot. I've alway been able to get them apart this way; Sometimes there's a screetching noise while the two pieces are turning against each other. You can always use a solder "slip coupling" to put a few inches of pipe back when you're making up the joint again. Hope this helps, Jeff -- Jeff Wisnia (W1BSV + Brass Rat '57 EE) "I before E except after C"....(The height of insufficient weird ancient science...) |
#3
|
|||
|
|||
Why solder will not melt?
The only reason it would not melt is if there is still water (even a small
amount) in the pipe. If this is not the case, then the solder is melted and you just need a tap with a hammer or twist (while hot) to open the joint. You may not have properly deburred the pipe when you made the joint and the burr is jammed in? If all else fails, cut the pipe again and add a short piece with a coupling... John "ississauga" wrote in message om... I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? |
#4
|
|||
|
|||
Why solder will not melt?
ississauga wrote:
I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? the solder was melting, but when you applied the heat you probably had the heat directed to the male section of pipe(the part that goes into the female fitting??), when it got hot it expaned and you cold not budge it.. the solder was not holding it on, it was the expansion that was holding it on.... try cutting it off and then putting new fittings in there.. not too many people reuse old fittings, they are pretty cheap... |
#5
|
|||
|
|||
Why solder will not melt?
(ississauga) wrote:
I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? "David Meiland" wrote in message ... (ississauga) wrote: Doesn't sound right to me. If the pipe was red hot, the solder was definitely liquid, or possibly you still had water in there. Now, getting a joint apart can be difficult. You need a thick pair of gloves, a wet rag, and maybe a pair of pliers. ....snip... If using a rag use a dry one. If you grab a really hot pipe with a wet rag the water turns to steam and there is a great chance the steam will blast through and around the cloth and burn your hand. Use a dry rag and it maintains its insulating properties, it may scorch of course, so don't use your best shirt. Also a wet rag tends to cool the work which you don't want. If you still had water in a red-hot pipe you would hear of hissing and popping and steam would come out the end. The deal here is to fasten one end of the assemply in a vise or clamp if it isn't already fixed and as you heat up the joint twist the free end with a gripping tool (wrench, spanner, multi-grips, pliers whatever you have). You will feel it start to give when the solder softens, which is long before red heat, then pull the joint apart. If the joint is very tight you may have to keep twisting back and forth as you work the free end off. David |
#6
|
|||
|
|||
Why solder will not melt?
I had the same problem with a copper soldered joint a year ago.....baffled
me for a while....I heated that dang joint until it was red as could be....but it wouldn't budge. Then I realized that the joint was NOT soldered with conventional solder, it was silver soldered....which meant that I would have needed to get out the acetylene torch to loosen the joint. I ended up cutting the joint and then going from there. Apparently, some builders silver solder because it's quicker...but makes it a pain in the behind for homeowners. Good luck -- Mark "ississauga" wrote in message om... I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? |
#7
|
|||
|
|||
Why solder will not melt?
"Mark S. Stiegel" wrote in message
... I had the same problem with a copper soldered joint a year ago.....baffled me for a while....I heated that dang joint until it was red as could be....but it wouldn't budge. Then I realized that the joint was NOT soldered with conventional solder, it was silver soldered....which meant that I would have needed to get out the acetylene torch to loosen the joint. I ended up cutting the joint and then going from there. Apparently, some builders silver solder because it's quicker...but makes it a pain in the behind for homeowners. Good luck -- Mark "ississauga" wrote in message om... I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? A MAPP gas burner (also a HD item) should melt the silver solder. Also, it will melt a regular solder faster and may melt it even of there is a tiny water leak from the shutoff valve. BTW, a MAPP-oxygen torch (from, where else, HD) will burn the copper pipe off . EJ |
#8
|
|||
|
|||
Why solder will not melt? (silver solder / lead free solder)
I believe that the current building codes require either silver solder,
or other "lead free" solder in any water supply lines. Definately DO NOT USE OLD LEAD BASED SOLDER!!! It just makes sense to limit the lead in our drinking water. Actually, I like using my oxy-acetylene torch for soldering. You just don't have to mess with not getting the joint hot enough. Of course, there is always the problem with getting it too hot. ----- CK ----- In article , says... I had the same problem with a copper soldered joint a year ago.....baffled me for a while....I heated that dang joint until it was red as could be....but it wouldn't budge. Then I realized that the joint was NOT soldered with conventional solder, it was silver soldered....which meant that I would have needed to get out the acetylene torch to loosen the joint. I ended up cutting the joint and then going from there. Apparently, some builders silver solder because it's quicker...but makes it a pain in the behind for homeowners. Good luck -- Mark "ississauga" wrote in message om... I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? |
#9
|
|||
|
|||
Why solder will not melt?
"ississauga" wrote in message
om... I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? It sounds to me that the joint was brazed, not soldered. By definition, brazing is done at higher temperatures than a common propane torch can achieve. |
#10
|
|||
|
|||
Why solder will not melt?
In article Michael H.
Pittsley says... I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? I assume you cleaned the joints real well and used flux to clean the joints of oxidation. This is not rocket science. If you are using the proper cleaning techniques and the proper solder, this should be easy with a standard propane torch -- I've done it dozens of times. -- Bob Morrison R.L. Morrison Engineering Co. Structural and Civil Engineering Poulsbo WA |
#11
|
|||
|
|||
Why solder will not melt?
Yes, lead free (95/5) on ALL joints in the potable water system. This
means everything, toilets, washing machines, etc.. Like I said, you can still use 50/50 on forced hot water systems and such that are protected from the potable water system by a backflow preventer. To this day I still personally use 50/50 on heating systems as I feel it is a little less brittle (very very fussy issue here) and feel that it will handle the higher heats of a hydronic heating system (200 degrees on some older systemes) better. That said, I know plumbers who prefer to buy one solder and use 95/5 exclusively and have been doing so for many years now with no issues whatsoever. The less brittle issue comes from working in industrial applications where we used to solder 4 and 6 inch copper lines with 50/50 and then cap them (the last bit of the joint was filled) with 95/5 for some rigidity to hold the 50/50 in as there was so much surface area on the joint... its just an old hold over and I am not at all worried that I will accidentally solder a potable joint with 50/50 having both in the tool box. Mark Terry wrote: Mark & Shauna wrote: As one post said, Lead free solder is now required. This does NOT mean silver solder. A house would cost a FORTUNE to plumb with silver solder. There was almost a rebelion in making the switch to 95/5 from 50/50 because it was a couple bucks higher per pound much less paying for silver solder. 95/5 (tin and antimony) does however melt a little hotter than 50/50 and can make a wet joint even harder. 50/50 however is still fine on any non-potable water lines (heating systems/etc). So any copper line which may be used for potable water requires the newer solder? I guess 'potable' would include kitchen cold and hot taps, therefore all joints in the hot water system, bathroom cold taps, for tooth brushing etc. Icemaker connections, dishwashers etc.? In other words anything with water you put in your mouth? Thanks for any comments. Terry. |
#12
|
|||
|
|||
Why solder will not melt?
Either there is still some water in the pipe - or more likely it's Silver Solder or Lead Free Solder, both of which are nearly impossible to melt with Propane. Buy or rent an acetylene torch, which are far hotter, and the pipe will come apart very quickly. Interesting. I've never had a problem sweating copper using a propane torch and lead free solder, the soft stuff anyway. Another alternative to propane may be MAPP gas? The plumbers who worked in our house used that, must be some reason, probably heats faster, thus saving time?. Looks like it's a bit more expensive than propane, but less costly thatn acetylene. Dave |
#13
|
|||
|
|||
Why solder will not melt?
Mark & Shauna wrote:
Yes, lead free (95/5) on ALL joints in the potable water system. This means everything, toilets, washing machines, etc.. Like I said, you can still use 50/50 on forced hot water systems and such that are protected from the potable water system by a backflow preventer. We don't drink out of the toilets in my house. :-) Matt |
#14
|
|||
|
|||
Why solder will not melt?
"Matthew S. Whiting" wrote in
: We don't drink out of the toilets in my house. :-) Matt Are your toilets on a separate water line than your faucets? I doubt it. -- Jim Yanik,NRA member remove null to contact me |
#15
|
|||
|
|||
Why solder will not melt?
Matthew S. Whiting wrote: Mark & Shauna wrote: Yes, lead free (95/5) on ALL joints in the potable water system. This means everything, toilets, washing machines, etc.. Like I said, you can still use 50/50 on forced hot water systems and such that are protected from the potable water system by a backflow preventer. We don't drink out of the toilets in my house. :-) Matt Yep, I am with ya on that one. But the bureaucrats say what they say. I suppose if you wanted to put a Watts9D on your toilet, DW, WM, etc. you could fight them to allow you to solder another few joints with 50/50. Come to think of it, I wonder how long it will be before they will make us implement some sort of extra safety measures on these appliances even though they already have one. After all, you have to install vac. breakers on your silcocks in the event that you fill your child's kiddie pool, he/she pee's in the pool, you leave the hose in the pool, there is a 50 alarm fire on your street at the _exact time_ you happen to be adding water to the pee tainted pool, the fire department drains all the water out of the mains (and more) siphoning contents of said pool back into your house, and you subsequently make a pot of pee flavored iced tea next time you run the tap. The same thing could happen with a DW/WM. Oh well,... Mark |
#16
|
|||
|
|||
Why solder will not melt?
|
#17
|
|||
|
|||
Why solder will not melt?
"Gary Slusser" wrote in message ...
"Dave" wrote (ississauga) wrote I am using a propane torch to melt a recently made solder joint holding together half inch copper plumbing pipes, but the solder won't melt no matter how long I heat it for. I leaked out the water and heated once till copper pipe turned red. Is there another way to melt the solder ? Pipe may be deformed. I had a real struggle with a small plumbing job recently. My main trouble was water hiding in the pipes. Probably worth having a MAPP gas torch for that. Also had a number of tiny leaks even though I had cleaned and fluxed each joint. Is there anything extra that can be done for better joints? Water converts to steam when enough heat is applied to boil water. Steam expands to a tremendous volume and seeks all exits from the plumbing, including molten solder in a joint. Air expands as it is heated too. It also builds pressure and wants to escape the plumbing. In a closed area of the plumbing system, both are guaranteed to cause soldered joints to leak. The more heat the more expansion. I suppose we could say the bigger the leak but that doesn't always prove to be true. Well once I had a known leak then water was a problem but I don't know if water was my initial problem. Maybe next time I will try cleaning the joint area with alcohol first. |
#18
|
|||
|
|||
Why solder will not melt?
...
|
#19
|
|||
|
|||
Why solder will not melt?
Why? for What? Now who in the hell are you talking at, you stupid
****? Will you ever use any usenet accepted protocol, or will you always be just a webtv **** stain? |
#20
Posted to alt.home.repair
|
|||
|
|||
Why solder will not melt?
On Thursday, June 26, 2003 at 9:31:24 AM UTC-5, mark Rainsley wrote:
Why? for What? Now who in the hell are you talking at, you stupid ****? Will you ever use any usenet accepted protocol, or will you always be just a webtv **** stain? Somebody is really having a bad day - hope it gets better |
#21
Posted to alt.home.repair
|
|||
|
|||
Why solder will not melt?
|
#22
Posted to alt.home.repair
|
|||
|
|||
Why solder will not melt?
On Mon, 22 Apr 2019 15:39:16 -0400, Tekkie®
wrote: posted for all of us... On Thursday, June 26, 2003 at 9:31:24 AM UTC-5, mark Rainsley wrote: Why? for What? Now who in the hell are you talking at, you stupid ****? Will you ever use any usenet accepted protocol, or will you always be just a webtv **** stain? Somebody is really having a bad day - hope it gets better Notice the date there scotty I doubt it. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
How do tell a liquid from a solid? | Metalworking | |||
Purity of copper when you melt it | Metalworking | |||
Solder | Electronics |