would a 1 inch hole weaken rim joist?
 

An electrician drilled a one-inch diameter hole in my house's rim joist
while adding a new circuit. A half inch hole is sufficient to pull the
romex through but a larger hole is more convenient for him to insert a
conduit fitting into the sheet rock at the end of the hole.

Would this one inch hole significantly weaken the rim joist? Should I
fill it with epoxy or something?

would a 1 inch hole weaken rim joist?
 

On 5/27/2015 2:26 PM, Bob wrote:
An electrician drilled a one-inch diameter hole in my house's rim joist
while adding a new circuit. A half inch hole is sufficient to pull the
romex through but a larger hole is more convenient for him to insert a
conduit fitting into the sheet rock at the end of the hole.

Would this one inch hole significantly weaken the rim joist? Should I
fill it with epoxy or something?

There is a simple rule to apply when drilling in joists. Generally,
drill holes with a diameter of no more than one-third the depth of the
joist, staying 2 in. away from the top and bottom if it's a dimensional
lumber joist. Therefore, if you have a 2 x 12 joist, your max is 3 3/4"
hole. The 1" hole is fine as long as it's not within the 2" from top or
bottom.

If you have manufactured I-joists, you can drill holes up to 1-1/2 in.
diameter almost anywhere in the web area (the area between the flanges).
Just stay 6 in. away from any end or load-bearing wall.

---
This email has been checked for viruses by Avast antivirus software.
http://www.avast.com

would a 1 inch hole weaken rim joist?
 

On Wed, 27 May 2015 11:26:57 -0700, Bob wrote:

An electrician drilled a one-inch diameter hole in my house's rim joist
while adding a new circuit. A half inch hole is sufficient to pull the
romex through but a larger hole is more convenient for him to insert a
conduit fitting into the sheet rock at the end of the hole.

Would this one inch hole significantly weaken the rim joist? Should I
fill it with epoxy or something?

No to the first question. To the second, caulk would be a good idea to
keep out weather or little critters

What would you say if he drilled a 4-1/4" hole for a dryer vent?

would a 1 inch hole weaken rim joist?
 

"Gordon Shumway" wrote in message
...
On Wed, 27 May 2015 11:26:57 -0700, Bob wrote:

An electrician drilled a one-inch diameter hole in my house's rim joist
while adding a new circuit. A half inch hole is sufficient to pull the
romex through but a larger hole is more convenient for him to insert a
conduit fitting into the sheet rock at the end of the hole.

Would this one inch hole significantly weaken the rim joist? Should I
fill it with epoxy or something?

No to the first question. To the second, caulk would be a good idea to
keep out weather or little critters

What would you say if he drilled a 4-1/4" hole for a dryer vent?



I'd say, "Well **** me Jean, I'll never smile again!"

would a 1 inch hole weaken rim joist?
 

Hi Bob,

An electrician drilled a one-inch diameter hole in my house's rim joist
while adding a new circuit. A half inch hole is sufficient to pull the
romex through but a larger hole is more convenient for him to insert a
conduit fitting into the sheet rock at the end of the hole.
Would this one inch hole significantly weaken the rim joist?

A one inch hole will not be a problem.

There are rules how big holes and notches can be in normal floor joists,
based on the size of the joist and where the hole is placed. This is to
ensure the joist is not weakened for carrying a load across a span.

However, a rim joist is generally supported along it's entire length,
either by the foundation/sill or the first floor walls below. Unless you
have a large point load, like a bearing post directly above, you can make
just about any size hole in the rim joist.

Of course, structure is good, so minimize holes and notches when possible.

Should I fill it with epoxy or something?

If there is more than 1/4" space in the hole, I would probably shoot in
some expanding foam, or push in a bit of foam backer rod (available at any
home center in many sizes). Then seal the exterior opening with a good
quality polyurethane caulk (exterior rated).

Of course, for a single small hole like this, caulk alone would probably be
all you need.

Anthony Watson
www.mountainsoftware.com
www.watsondiy.com

would a 1 inch hole weaken rim joist?
 

On 5/27/2015 2:26 PM, Bob wrote:
An electrician drilled a one-inch diameter hole in my house's rim joist while adding a new circuit. A half inch hole is sufficient to pull the romex through but a larger hole is more convenient for him to insert a conduit fitting into the sheet rock at
the end of the hole.

Would this one inch hole significantly weaken the rim joist?

You're probably ok as long as the electrician got a permit and had the structural modification inspected.

Should I fill it with epoxy or something?

If you do, make sure you get a permit and have the work inspected.

would a 1 inch hole weaken rim joist?
 

On 5/27/2015 4:14 PM, Bill wrote:
On 5/27/2015 2:26 PM, Bob wrote:
An electrician drilled a one-inch diameter hole in my house's rim
joist while adding a new circuit. A half inch hole is sufficient to
pull the romex through but a larger hole is more convenient for him to
insert a conduit fitting into the sheet rock at
the end of the hole.

Would this one inch hole significantly weaken the rim joist?

You're probably ok as long as the electrician got a permit and had the
structural modification inspected.

Should I fill it with epoxy or something?

If you do, make sure you get a permit and have the work inspected.

You have to be kidding about a permit and structural modification
inspection!

would a 1 inch hole weaken rim joist?
 

On 5/27/2015 9:01 PM, IGot2P wrote:
On 5/27/2015 4:14 PM, Bill wrote:
On 5/27/2015 2:26 PM, Bob wrote:
An electrician drilled a one-inch diameter hole in my house's rim
joist while adding a new circuit. A half inch hole is sufficient to
pull the romex through but a larger hole is more convenient for him to
insert a conduit fitting into the sheet rock at
the end of the hole.

Would this one inch hole significantly weaken the rim joist?

You're probably ok as long as the electrician got a permit and had the
structural modification inspected.

Should I fill it with epoxy or something?

If you do, make sure you get a permit and have the work inspected.

You have to be kidding about a permit and structural modification
inspection!


If you're humor impaired, may I suggest reading the entire thread to
relieve any confusion?

If you can't run with the big dogs, stay up on the porch! g