Gorilla Glue / Polyurethane Glue Question
 

Hello,

I may be wrong, but I think that Gorilla Glue product is a Polyurthane glue.
Correct ?

In any event, when would one use this Gorilla glue rather than, e.g.,
the typical 2 part epoxy ?

Would be for a wood project.

Thanks,
Bob

---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com

Gorilla Glue / Polyurethane Glue Question
 

On 09/27/2014 4:39 PM, Bob wrote:
Hello,

I may be wrong, but I think that Gorilla Glue product is a Polyurthane
glue.
Correct ?

In any event, when would one use this Gorilla glue rather than, e.g.,
the typical 2 part epoxy ?

Would be for a wood project.
....

The original is polyurethane, yes. There is now a wood glue that is PVA.

The only reason to ever use the original for a wood glue is if must have
fully waterproof glue, not just the ANSI tests. It isn't as strong as a
PVA and has the other disadvantage that it foams on curing as well as
does not clean up w/ water.

It has the advantage over PVA glues for bonding other materials where
the PVA glues don't work but it's simply not of much real use for normal
woodworking. It is somewhat cheaper and is of a little less bother than
the two-part resorcinols, but I'll take one of them over it despite that
because of the foaming nature that is such a pita.

--

Gorilla Glue / Polyurethane Glue Question
 

On 9/27/2014 6:08 PM, dpb wrote:
On 09/27/2014 4:39 PM, Bob wrote:
Hello,

I may be wrong, but I think that Gorilla Glue product is a Polyurthane
glue.
Correct ?

In any event, when would one use this Gorilla glue rather than, e.g.,
the typical 2 part epoxy ?

Would be for a wood project.
...

The original is polyurethane, yes. There is now a wood glue that is PVA.

The only reason to ever use the original for a wood glue is if must have
fully waterproof glue, not just the ANSI tests. It isn't as strong as a
PVA and has the other disadvantage that it foams on curing as well as
does not clean up w/ water.

It has the advantage over PVA glues for bonding other materials where
the PVA glues don't work but it's simply not of much real use for normal
woodworking. It is somewhat cheaper and is of a little less bother than
the two-part resorcinols, but I'll take one of them over it despite that
because of the foaming nature that is such a pita.

--


Correct and I don't think the polyurethanes have the stability of the
other glues.

Gorilla glue sometimes comes in handy but my biggest complaint is that
moisture absorption hardens it and makes it useless in the package.
I think the bottle is polyethylene which is one of the worst barrier
polymers for moisture, oxygen and CO2.

Gorilla Glue / Polyurethane Glue Question
 

On 9/27/2014 5:39 PM, Bob wrote:
Hello,

I may be wrong, but I think that Gorilla Glue product is a Polyurthane
glue.
Correct ?

Yes.


In any event, when would one use this Gorilla glue rather than, e.g.,
the typical 2 part epoxy ?

When you have small gap that you don't have the ability to fix properly.


Would be for a wood project.

Special circumstances? A good PVA wood glue makes a joint stronger than
wood itself to using a stronger glue is of little benefit. That said,
if it is going to be submerged or in really west conditions, the epoxy
or urethane may be better.

I've done hobby woodworking for a number of years and never used Gorilla
glue, but I have used epoxy for some outdoor benches. I've also used
Titebond 3 with good outdoor results.

Bob:

Gorilla glue is just like so many other products; they don't stand out in any particular catagory.

For wood, white wood glue has the advantages that it dries clear for a nearly invisible repair. It's not very water resistant, and so you don't want to use it outside.

For wood, LePage's PL Premium construction adhesive has the advantage that it's about the strongest glue you can get for gluing wood together (except perhaps for a two part epoxy), and it's completely waterproof like epoxy, so it can be used outside.

LePage's has modified their PL Premium formulation to produce construction adhesives with higher initial tack, but so far as I know, the ultimate bond strength after curing is still the same as with the original PL Premium.

So, if you want a near invisible repair, use white wood glue. If it's bond strength you're after, PL Premium is the way to go. Gorilla Glue is one of those other hundreds of adhesive products that doesn't stand out in any particular catagory.

Gorilla Glue / Polyurethane Glue Question
 

On 09/27/2014 5:38 PM, Ed Pawlowski wrote:
On 9/27/2014 5:39 PM, Bob wrote:
....

In any event, when would one use this Gorilla glue rather than, e.g.,
the typical 2 part epoxy ?

When you have small gap that you don't have the ability to fix properly.

....

But the polyurethanes are _not_ gap filling in any useful sense for such
a purpose -- you'll end up w/ a porous mess blob with a bunch of tiny
air bubbles, not a solid mass in the gap.

--

Gorilla Glue / Polyurethane Glue Question
 

On 9/27/2014 6:30 PM, Frank wrote:
Gorilla glue sometimes comes in handy but my biggest complaint is that
moisture absorption hardens it and makes it useless in the package.
I think the bottle is polyethylene which is one of the worst barrier
polymers for moisture, oxygen and CO2.


I've learned to buy the smallest bottle.
For just that reason.

..
Christopher A. Young
Learn about Jesus
www.lds.org
..

Give that a little thought. Polyethylene is what's used for vapour barrier in the walls of most buildings. They wouldn't use it for vapour barrier if it was as poor a barrier to moisture as you suggest. I expect what the problem is is that every time you open the bottle, you fill the container with more warm humid air and the glue gradually hardens up in small steps until it becomes unuseable.

I don't know whether Gorilla Glue is a moisture cure polyurethane or not, but if it is, then the trick to storing it for long periods is to put it in a place with negligible moisture content, and that means your fridge's freezer (best) or upside down in a container of motor oil. I've stored PL Premium both ways, and both ways work, but the freezer works best.

LePage's PL Premium is a moisture cure construction adhesive, and I keep it in my freezer between projects where I need it. I just "candy cane" it by squeezing a little bit of it out and immediately put it in the freezer. I only squeeze out enough that I can grip reasonably well.

The low temperature in the freezer both ensures minimal humidity levels in the air and minimal chemical activity so that whatever humidity there is in the freezer air doesn't react with the construction adhesive. The result is that the stuff will keep for a very long time under these conditions. The part that got squeezed out when I candy caned it will become hard because of the moisture it absorbed when squeezed out. But, I just put the cold tube in my caulking gun, apply pressure to the glue and pull the candy cane out, and the new glue will start to slowly come oozing out. Let it warm up, and it's ready to use again. I've stored PL Premium for well over a year in my freezer, using it periodically as needed, and it's still good to use now.

I expect the Gorilla Glue, if it's a moisture cure polyurethane glue could be stored equally well in a freezer.

I've also cut the top off an old milk jug and filled it about an inch full of motor oil. Candy cane a bit of PL Premium out of the tube and immediately put it upside down in the oil. The glue at the tip of the tube can't cure because there's negligible H2O content in the motor oil, and that prevents the glue from curing even at room temperature.

It's just a matter of understanding that the glue requires moisture to cure, and recognizing those places where moisture is all but completely absent.

Gorilla Glue / Polyurethane Glue Question
 

I've never tried Gorilla Glue, but have good luck with plain
Titebond. I like the non-waterproof because if I make a
mistake I can take it apart with a little misting of water.
Yet it's very strong. But that's for smooth joints with
good contact: Cabinet parts, moldings, etc. For contacts
with gaps, like a chair dowel, or for use with resinous
exotics, I like to use 5-minute epoxy.

Gorilla Glue / Polyurethane Glue Question
 

On Sat, 27 Sep 2014 17:39:21 -0400, Bob wrote:

Hello,

I may be wrong, but I think that Gorilla Glue product is a Polyurthane glue.
Correct ?

In any event, when would one use this Gorilla glue rather than, e.g.,
the typical 2 part epoxy ?

When you're trying to glue together a gorilla.

Would be for a wood project.

Thanks,
Bob

Gorilla Glue / Polyurethane Glue Question
 

On 9/27/14, 7:48 PM, Stormin Mormon wrote:
On 9/27/2014 6:30 PM, Frank wrote:
Gorilla glue sometimes comes in handy but my biggest complaint is that
moisture absorption hardens it and makes it useless in the package.
I think the bottle is polyethylene which is one of the worst barrier
polymers for moisture, oxygen and CO2.


I've learned to buy the smallest bottle.
For just that reason.

.
Christopher A. Young
Learn about Jesus
www.lds.org
.

I was disgusted when the first one hardened. Then I bought another.
It's convenient. It seems flexible, which is good for some uses. The
foaming seems to help it grab uneven surfaces.

The second bottle had a tapered metal stopper, but it, too hardened. If
I ever buy it again, I'll grease the threads, to make them easier to
unscrew and stop moisture from creeping in that way. That seemed to
preserve some polyurethane shoe stuff I had.

Gorilla Glue / Polyurethane Glue Question
 

On 09/27/2014 6:30 PM, dpb wrote:
....

But the polyurethanes are _not_ gap filling in any useful sense for such
a purpose -- you'll end up w/ a porous mess blob with a bunch of tiny
air bubbles, not a solid mass in the gap.
....

Followup -- this is a "DAMHIKT" moment...way back when G-G was pretty
new and all the rage of the TV commercials in the big initial blitz I
thought it sounded as though it would be useful for the purpose and the
missus had a cutting board she liked very well that had developed some
problems.

Thinking the filling and the waterproof was a great combination w/ less
hassle than epoxy or resorcinol Weldwood two part, I commenced to begin.
It was a nightmare...had all glued up w/ mostly good joint w/ the
exception of the location with the known gap that I ensured had
sufficient to fill w/ some squeeze-out. As it began to dry/cure, it
started foaming like a miniature insulation foam can spray and soon was
a mess a-making. I've never used it since for anything but the odd
repair job of mismatch material or the like for which it does serve a
function.

I've been amazed at the exhibition of how a perception can be created
and a product niche built from scratch almost purely by the strength of
advertising that Gorilla did...they did pick a great trademark and ran a
powerful media blitz and won...

--