Do they make holesaw blades for steel doors?
 

Do they make holesaw blades for steel doors?

In order to install a door lock, one needs to make about a 2 inch hole
in a door. On a wooden door, a common hole saw works fine. But on a
steel door, (which is two layers of a fairly thin steel with wood
sandwiched in the middle, around the perimeter).

I did this once with a standard holesaw, ruined the saw and made a very
messy hole in the door which the lock did not cover real well, forcing
me to just put silicone caulk around the base of the lock to seal the
bad spots. I also had to file the hole several times to get the lock
to fit properly because it was not round and offset on an angle.

Now I have to do it again, and want the right tool. I'm not going thru
that hassle again, as well as messing up the door.

There must be some sort of tool made that will cut both the metal and
the wood.

Do they make holesaw blades for steel doors?
 

On 12/5/2012 3:25 AM, wrote:
There must be some sort of tool made that will cut both the metal and
the wood.


http://www.youtube.com/watch?v=QedkDcd4TJA

Do they make holesaw blades for steel doors?
 

wrote in message
...
Do they make holesaw blades for steel doors?

Yes. Pretty standard tool. Check your local big box or hardware store.

Do they make holesaw blades for steel doors?
 

I'd suggest to call a locksmith. I've installed several dozen deadbolts on
metal clad doors, and that's neveer been an issue for me.

Christopher A. Young
Learn more about Jesus
www.lds.org
..

wrote in message
...
Do they make holesaw blades for steel doors?

In order to install a door lock, one needs to make about a 2 inch hole
in a door. On a wooden door, a common hole saw works fine. But on a
steel door, (which is two layers of a fairly thin steel with wood
sandwiched in the middle, around the perimeter).

I did this once with a standard holesaw, ruined the saw and made a very
messy hole in the door which the lock did not cover real well, forcing
me to just put silicone caulk around the base of the lock to seal the
bad spots. I also had to file the hole several times to get the lock
to fit properly because it was not round and offset on an angle.

Now I have to do it again, and want the right tool. I'm not going thru
that hassle again, as well as messing up the door.

There must be some sort of tool made that will cut both the metal and
the wood.

Do they make holesaw blades for steel doors?
 

On Dec 5, 7:35*am, "The Streets"
wrote:
wrote in message

... Do they make holesaw blades for steel doors?

Yes. *Pretty standard tool. *Check your local big box or hardware store.

What you want is a bi-metal hole saw with
fine teeth. Readily available at HD, hardware stores,
online, etc.

Do they make holesaw blades for steel doors?
 

wrote:

Do they make holesaw blades for steel doors?

In order to install a door lock, one needs to make about a 2 inch hole
in a door. On a wooden door, a common hole saw works fine. But on a
steel door, (which is two layers of a fairly thin steel with wood
sandwiched in the middle, around the perimeter).

I did this once with a standard holesaw, ruined the saw and made a very
messy hole in the door which the lock did not cover real well, forcing
me to just put silicone caulk around the base of the lock to seal the
bad spots. I also had to file the hole several times to get the lock
to fit properly because it was not round and offset on an angle.

Now I have to do it again, and want the right tool. I'm not going thru
that hassle again, as well as messing up the door.

There must be some sort of tool made that will cut both the metal and
the wood.

I have these Bosch Progressor holesaws:

http://www.screwfix.com/p/bosch-prog...kit-8-pc/45172

They are the best ones I have used to date - I've used them on wood,
plasterboard (sheetrock), fiberglass and plastics. I have not tried on metal
- but they claim to. I think you'd be fine with "thin steel", say less than
1/16".

--
Tim Watts Personal Blog: http://www.dionic.net/tim/

"A fanatic is one who can't change his mind and won't change the subject."

Do they make holesaw blades for steel doors?
 

Do they make holesaw blades for steel doors?

In order to install a door lock, one needs to make about a 2 inch hole
in a door. On a wooden door, a common hole saw works fine. But on a
steel door, (which is two layers of a fairly thin steel with wood
sandwiched in the middle, around the perimeter).

I did this once with a standard holesaw, ruined the saw and made a very
messy hole in the door which the lock did not cover real well, forcing
me to just put silicone caulk around the base of the lock to seal the
bad spots. I also had to file the hole several times to get the lock
to fit properly because it was not round and offset on an angle.

Now I have to do it again, and want the right tool. I'm not going thru
that hassle again, as well as messing up the door.

There must be some sort of tool made that will cut both the metal and
the wood.


*There are plenty of metal cutting holesaws available including the Ridgid
and Milwaukee brands sold at Home Depot. One mistake that I see too often
is that some people use them in high speed drills. Holesaws are to be used
at low RPM's around 300-400. The 1000 RPM pistol drills cook the teeth and
cause more wobble which leads to a sloppy hole. Some lubrication helps
things along. I seem to recall an idea from a fellow electrician which
involved putting an oiled felt pad inside of the holesaw and the heat from
the saw would cause some of the oil to drip down.

Do they make holesaw blades for steel doors?
 

On 12/05/2012 05:14 AM, wrote:
On Dec 5, 7:35 am, "The Streets"
wrote:
wrote in message

... Do they make holesaw blades for steel doors?

Yes. Pretty standard tool. Check your local big box or hardware store.

What you want is a bi-metal hole saw with
fine teeth. Readily available at HD, hardware stores,
online, etc.

What he said; you want a bi-metal hole saw.

Jon

I agree with the previous post that suggested you buy a "bi-metal" hole saw. Bi-metal hack saw and jig saw blades are toothed blades that have a hardened toothed strip precision welded (laser or otherwise) to a softer and tougher steel which comprises most of the blade. Because the toothed section is made of a hardened tool steel (which is a much harder metal than the rest of the blade) it's suitable for cutting metal, especially relatively soft steels like the mild steel they use for cladding steel doors.

But, if the same thing happens, keep in mind that Weiser (at least) and I expect most lock manufacturers make escutcheon rings for their lock sets that can be used to cover up the mess better than silicone. The escutcheon ring shown here is the Weiser #1639 escutcheon trim:



It fits both Weiser deadbolts and lock sets. It is available in both square and round versions, in both brushed aluminum and polished brass. Earlier Weiser deadbolts could be "popped off" a door with a sufficiently strong prybar, and that would muck up the door around the deadbolt. The 1639 has a recessed section in the middle that the deadbolt fits into, thereby making it much harder to get a pry bar under the deadbolt. I'm thinking other lock manufacturers would make something similar which would fit your lockset or deadbolt better.

Do they make holesaw blades for steel doors?
 

In article ,
wrote:
Do they make holesaw blades for steel doors?

In order to install a door lock, one needs to make about a 2 inch hole
in a door. On a wooden door, a common hole saw works fine. But on a
steel door, (which is two layers of a fairly thin steel with wood
sandwiched in the middle, around the perimeter).

I did this once with a standard holesaw, ruined the saw and made a very
messy hole in the door which the lock did not cover real well, forcing
me to just put silicone caulk around the base of the lock to seal the
bad spots. I also had to file the hole several times to get the lock
the wood.
...etc...

A good quality hole saw like a Morse or Starret will go through several
standard steel-clad before it needs to be resharpened. For a one-off
use, you can get away with a throw-away priced blade from Harbor Freight.





--
The best argument against democracy is a five-minute conversation
with the average voter. (Winston Churchill)

Larry Wasserman - Baltimore Maryland - lwasserm(a)sdf. lonestar. org