How to connect copper to PVC?
 

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--
www.rationality.net

How to connect copper to PVC?
 

On Oct 31, 12:26*pm, "walther" wrote:
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

Check out SharkBite connectors, available at all plumbing stores and
most Home Centers.

Cut...Puch...Done

http://www.sharkbite.com/usa/en/applications

How to connect copper to PVC?
 

On Mon, 31 Oct 2011 09:26:29 -0700, "walther"
wrote:

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?
+***

SharkBite® Push-Fit Fittings

A Connection System For Copper, CTS CPVC and PEX Pipe

The SharkBite® fittings line presents a revolutionary solution to
connecting water distribution pipe. Our SharkBite® Push-Fit Fittings
are the fastest, easiest way to join copper, CTS CPVC and PEX pipe in
any combination. With no soldering, clamps, unions or glue. The line
includes more than 130 different fittings in a variety of sizes.
Certified to 200 psi and 200°F (93°C).

http://sharkbite.rapidfire.com.au/usa/en/products/push-fit-products/push-fit-fittings


If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--
www.rationality.net

How to connect copper to PVC?
 

On Oct 31, 12:26*pm, "walther" wrote:
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

as others have said, sharkbite ought to make a fitting that will turn
a plain copper pipe into a male 3/4" NPT then use a PVC FPT to glue
socket fitting, continue from there.

Personally I'd be tempted to just solder the one fitting onto the
copper rather than spending the $$$ for sharkbite, but then again I
have all the tools and supplies. If you need to buy all that stuff
and this is a one-off job the sharkbite starts to look like the most
economical solution.

nate

How to connect copper to PVC?
 

Best way would be to glue a female adapter on the pvc then you could screw
in a copper adder and carry on or vice versa solder a female adapter on the
copper then screw in a pvc adaper and carry on with the pvc pipe
"walther" wrote in message
...
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--
www.rationality.net

How to connect copper to PVC?
 

"walther" wrote in message
...
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?


Genova makes one:
http://www.lowes.com/pd_22647-322-53...pvc&facetInfo=

How to connect copper to PVC?
 

"walther" wrote in message
...
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Disregard my last post. You said PVC to copper (not CPVC). Here are some
transition fitings:

http://flexpvc.com/cart/agora.cgi?pr...-Pipe-Adapters

How to connect copper to PVC?
 

What is the best way - without soldering - to connect a 3/4" rigid
copper pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder
joint? Thank you

Walter--
www.rationality.net

don &/or Lucille wrote:
Best way would be to glue a female adapter on the pvc then you could
screw in a copper adder and carry on or vice versa solder a female
adapter on the copper then screw in a pvc adaper and carry on with
the pvc pipe "walther" wrote in message
...

Don't use metal Male threaded fittings into Female PVC. The PVC will expand or
split, resulting in leaks. The reverse is better.

How to connect copper to PVC?
 

On Oct 31, 4:26*pm, "walther" wrote:
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

See if you can find a compression fitting that will fit/can be adapted
to fit both.
If it is a pressure joint you will need an insert in the PVC pipe to
stop it collapsing as you tighten the compression nut.

How to connect copper to PVC?
 

"don &/or Lucille" wrote in
:

Best way would be to glue a female adapter on the pvc then you could
screw in a copper adder and carry on or vice versa solder a female
adapter on the copper then screw in a pvc adaper and carry on with the
pvc pipe "walther" wrote in message
...
What is the best way - without soldering - to connect a 3/4" rigid
copper pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder
joint?

Thank you

Walter--
www.rationality.net




the only proper way is to solder a threaded fitting on the copper pipe,then
screw on the proper PVC adapter,and glue up your PVC pipe network to that
adapter.

you need a propane or MAPP torch,flux-core plumbing solder(no lead!!),emery
paper to clean the solder joint areas,and maybe a heat shield if there's
wood or a wall close by.

The folks at Home Depot or Lowes ought to be able to show you how to do
this properly. they might even teach a class on it.

--
Jim Yanik
jyanik
at
localnet
dot com

How to connect copper to PVC?
 

On Oct 31, 4:00*pm, Jim Yanik wrote:
"don &/or Lucille" wrote :





Best way would be to glue a female adapter on the pvc then you could
screw in a copper adder and carry on or vice versa solder a female
adapter on the copper then screw in a pvc adaper and carry on with the
pvc pipe "walther" wrote in message
...
What is the best way - without soldering - to connect a 3/4" rigid
copper pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder
joint?

Thank you

Walter--
www.rationality.net

the only proper way is to solder a threaded fitting on the copper pipe,then
screw on the proper PVC adapter,and glue up your PVC pipe network to that
adapter.

you need a propane or MAPP torch,flux-core plumbing solder(no lead!!),emery
paper to clean the solder joint areas,and maybe a heat shield if there's
wood or a wall *close by.

The folks at Home Depot or Lowes ought to be able to show you how to do
this properly. they might even teach a class on it.

--
Jim Yanik
jyanik
at
localnet
dot com- Hide quoted text -

- Show quoted text -

Why is that the only "proper" way?

Are you not a fan of SharkBites?

How to connect copper to PVC?
 

On Oct 31, 1:19*pm, N8N wrote:
On Oct 31, 12:26*pm, "walther" wrote:

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

as others have said, sharkbite ought to make a fitting that will turn
a plain copper pipe into a male 3/4" NPT then use a PVC FPT to glue
socket fitting, continue from there.

Personally I'd be tempted to just solder the one fitting onto the
copper rather than spending the $$$ for sharkbite, but then again I
have all the tools and supplies. *If you need to buy all that stuff
and this is a one-off job the sharkbite starts to look like the most
economical solution.

nate

It might also matter *where* the fitting will be located.

I too will sweat copper or glue PVC in the majority of cases, but
there have been times, such as putting a T in copper to tap in for a
PEX run way up in a joist bay, that the expense of SharkBites don't
seem so bad compared to trying to sweat copper in a cramped location
while contorted on top of step ladder in a dank, dusty basement.

How to connect copper to PVC?
 

On Mon, 31 Oct 2011 09:26:29 -0700, "walther"
wrote:

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--
www.rationality.net

Half a roll of duct tape should do the job for a couple weeks or so...
Just make sure the pipes are dry when you tape them together.
Be sure to secure the pipes to the floor joists or wall studs with
bungie cords.

Duct tape and bungie cords are all you will ever need to repair
everything.

How to connect copper to PVC?
 

That's what my dentist says. Do you know him? I went to an
advanced dentist, he also uses WD-40 the lubricant.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


wrote in message
...

Half a roll of duct tape should do the job for a couple
weeks or so...
Just make sure the pipes are dry when you tape them
together.
Be sure to secure the pipes to the floor joists or wall
studs with
bungie cords.

Duct tape and bungie cords are all you will ever need to
repair
everything.

How to connect copper to PVC?
 

I hope they last for many generations. I'm not sure I trust
them, enough to put in an out of the way place that's not
likely to be noticed.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"DerbyDad03"
wrote in message
...

It might also matter *where* the fitting will be located.

I too will sweat copper or glue PVC in the majority of
cases, but
there have been times, such as putting a T in copper to tap
in for a
PEX run way up in a joist bay, that the expense of
SharkBites don't
seem so bad compared to trying to sweat copper in a cramped
location
while contorted on top of step ladder in a dank, dusty
basement.

How to connect copper to PVC?
 

Go to H.D. or a Plumbing Supply and have them give you a quick demo on
"Shark Bite" . Will solve your problem !

Bill
"walther" wrote in message
...
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--
www.rationality.net

How to connect copper to PVC?
 

On Oct 31, 10:52*am, "don &/or Lucille"
wrote:
Best way would be to glue a female adapter on the pvc then you could screw
in a copper adder and carry on or vice versa solder a female adapter on the
copper then screw in a pvc adaper and carry on with the pvc pipe"walther" wrote in message

...







What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--
www.rationality.net

One way is good, the other problematic....
Metal male thread & PVC female thread invites a splitting failure.

The reverse is more robust,

oops!

already posted....

plus don't used those wimpy slip to male thread PVC fittings
Use a 6" long SCH 80 3/4" threaded PVC nipple, cut it in half and
attach it to the PVC pipe with a coupling.

MUCH stronger

As others have said....SharkBites.

btw (OP) that would be copper tube not pipe.

cheers
Bob

How to connect copper to PVC?
 

On Oct 31, 10:19*am, N8N wrote:
On Oct 31, 12:26*pm, "walther" wrote:

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

as others have said, sharkbite ought to make a fitting that will turn
a plain copper pipe into a male 3/4" NPT then use a PVC FPT to glue
socket fitting, continue from there.

Personally I'd be tempted to just solder the one fitting onto the
copper rather than spending the $$$ for sharkbite, but then again I
have all the tools and supplies. *If you need to buy all that stuff
and this is a one-off job the sharkbite starts to look like the most
economical solution.

nate

NO!!! Never use a female pipe thread PVC fitting to transition. When
you tighten it it tends to crack the fitting. I learned that the
hard way when my new well system sprang a leak in the middle of
January under 2 ft of snow cover. Always use a male PVC adapter..

Harry K

How to connect copper to PVC?
 

On 10/31/2011 9:26 AM, walther wrote:
What is the best way - without soldering - to connect a 3/4" rigid
copper pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter-- www.rationality.net

compression FEMALE adaptor on the copper side. PVC male adaptor on the
plastic side. Screw together.


--
Steve Barker
remove the "not" from my address to email

How to connect copper to PVC?
 

On Mon, 31 Oct 2011 14:33:50 -0600, jw wrote:
Duct tape and bungie cords are all you will ever need to repair
everything.

Duct tape didn't work when my clothes dryer belt snapped the other day
and nowhere in town had a replacement. I never thought of trying a bungie
cord, though ;-)

How to connect copper to PVC?
 

"Oren" wrote in message
...
On Mon, 31 Oct 2011 09:26:29 -0700, "walther"
wrote:

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?
+***

SharkBite® Push-Fit Fittings

A Connection System For Copper, CTS CPVC and PEX Pipe

The SharkBite® fittings line presents a revolutionary solution to
connecting water distribution pipe. Our SharkBite® Push-Fit Fittings
are the fastest, easiest way to join copper, CTS CPVC and PEX pipe in
any combination. With no soldering, clamps, unions or glue. The line
includes more than 130 different fittings in a variety of sizes.
Certified to 200 psi and 200°F (93°C).

http://sharkbite.rapidfire.com.au/usa/en/products/push-fit-products/push-fit-fittings


The first time I saw Shark Bite fittings, it was like "This is a dream,
right?" High priced crap! "Oh, not to worry, full money back guarantee."

Tried it on the little test pieces they had there, and I was suspicious.
THIS WAS TOO EASY!

I had to fix 5 burst pipes under a mountain cabin, four of them in very
tight spaces. Crawl spaces. Get under there and work at arm length spaces.

When I was introduced to them by the guy at Big Orange, I was highly
skeptical. I got some, and used them, and fixed all my problems in 1/10 of
the time it would have taken. And no fire sweating fittings under a wood
cabin with leaves a foot thick all over, and in positions that would have
been difficult for a contortionist.

Plain and simple, if you haven't tried them, look at them.

Coming from a person who is highly skeptical about everything in life, they
work and are worth the money, and will make the job sooooooooooo much
simpler. Lots of places where sweating is dangerous, can't get in there,
stud's too tight, can't do this or that ..................... SHARK BITE!
Copper to pex to pvc to copper to pex, it all just fits together if the OD
is the same. It's so simple, it makes stupid people feel guilty. (Or at
least in my case.)

The repairs are going on three seasons old now, a concern I had of them,
whether or not they'd last. But even if they just last five years, I'd
happily replace with them again just for the convenience and safety aspect
of the job.

YMMV, and all that stuff ..................

Steve

How to connect copper to PVC?
 

"N8N" wrote in message
...
On Oct 31, 12:26 pm, "walther" wrote:
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

as others have said, sharkbite ought to make a fitting that will turn
a plain copper pipe into a male 3/4" NPT then use a PVC FPT to glue
socket fitting, continue from there.

Personally I'd be tempted to just solder the one fitting onto the
copper rather than spending the $$$ for sharkbite, but then again I
have all the tools and supplies. If you need to buy all that stuff
and this is a one-off job the sharkbite starts to look like the most
economical solution.

nate

If you don't have the soldering rig, a $7 Sharkbite is less than a burner, a
tank of fuel, solder, flux, and all the other stuff. A lot less.

Steve

How to connect copper to PVC?
 

"Jim Yanik" wrote


the only proper way is to solder a threaded fitting on the copper
pipe,then
screw on the proper PVC adapter,and glue up your PVC pipe network to that
adapter.

you need a propane or MAPP torch,flux-core plumbing solder(no
lead!!),emery
paper to clean the solder joint areas,and maybe a heat shield if there's
wood or a wall close by.

The folks at Home Depot or Lowes ought to be able to show you how to do
this properly. they might even teach a class on it.

--
Jim Yanik


Huh? "Proper way"? There may be a way that is "proper", and then there is
a way that is simple, safe, effective, long lasting, cost efficient, and
labor saving. Sometimes the lesser is just as good as the "proper" way.

Give me safe, easy and long lasting.

There's a hundred ways to cook a poodle.

But it all tastes like chicken in the end, don't it?

Steve

How to connect copper to PVC?
 

On 11/1/2011 2:32 PM, Steve B wrote:
wrote in message
...
On Oct 31, 12:26 pm, wrote:
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

as others have said, sharkbite ought to make a fitting that will turn
a plain copper pipe into a male 3/4" NPT then use a PVC FPT to glue
socket fitting, continue from there.

Personally I'd be tempted to just solder the one fitting onto the
copper rather than spending the $$$ for sharkbite, but then again I
have all the tools and supplies. If you need to buy all that stuff
and this is a one-off job the sharkbite starts to look like the most
economical solution.

nate

If you don't have the soldering rig, a $7 Sharkbite is less than a burner, a
tank of fuel, solder, flux, and all the other stuff. A lot less.

Steve



sharkbites don't fit pvc. they fit CPVC.


--
Steve Barker
remove the "not" from my address to email

How to connect copper to PVC?
 

On Nov 2, 12:34*am, Steve Barker wrote:
On 11/1/2011 2:32 PM, Steve B wrote:





*wrote in message
....
On Oct 31, 12:26 pm, *wrote:
What is the best way - without soldering - to connect a 3/4" rigid copper
pipe to 3/4" PVC 40?

If there is no good way, what do I need to buy to make a solder joint?

Thank you

Walter--www.rationality.net

as others have said, sharkbite ought to make a fitting that will turn
a plain copper pipe into a male 3/4" NPT then use a PVC FPT to glue
socket fitting, continue from there.

Personally I'd be tempted to just solder the one fitting onto the
copper rather than spending the $$$ for sharkbite, but then again I
have all the tools and supplies. *If you need to buy all that stuff
and this is a one-off job the sharkbite starts to look like the most
economical solution.

nate

If you don't have the soldering rig, a $7 Sharkbite is less than a burner, a
tank of fuel, solder, flux, and all the other stuff. *A lot less.

Steve

sharkbites don't fit pvc. *they fit CPVC.

I was thinking the Sharkbite would be for the copper, to avoid the
soldering.

I didn't think about Steve B's point but it makes sense. I will have
to file that one away, although I know that I've seen FPT PVC fittings
before.

How to connect copper to PVC?
 

On Nov 1, 5:31*pm, "Steve B" wrote:
"Oren" wrote in message

...





On Mon, 31 Oct 2011 09:26:29 -0700, "walther"
wrote:

What is the best way - without soldering - to connect a 3/4" rigid copper
pipe *to 3/4" PVC 40?
+***

SharkBite® Push-Fit Fittings

A Connection System For Copper, CTS CPVC and PEX Pipe

The SharkBite® fittings line presents a revolutionary solution to
connecting water distribution pipe. Our SharkBite® Push-Fit Fittings
are the fastest, easiest way to join copper, CTS CPVC and PEX pipe in
any combination. With no soldering, clamps, unions or glue. The line
includes more than 130 different fittings in a variety of sizes.
Certified to 200 psi and 200°F (93°C).

http://sharkbite.rapidfire.com.au/usa/en/products/push-fit-products/p....

The first time I saw Shark Bite fittings, it was like "This is a dream,
right?" *High priced crap! *"Oh, not to worry, full money back guarantee."

Tried it on the little test pieces they had there, and I was suspicious.
THIS WAS TOO EASY!

I had to fix 5 burst pipes under a mountain cabin, four of them in very
tight spaces. *Crawl spaces. *Get under there and work at arm length spaces.

When I was introduced to them by the guy at Big Orange, I was highly
skeptical. *I got some, and used them, and fixed all my problems in 1/10 of
the time it would have taken. *And no fire sweating fittings under a wood
cabin with leaves a foot thick all over, and in positions that would have
been difficult for a contortionist.

Plain and simple, if you haven't tried them, look at them.

Coming from a person who is highly skeptical about everything in life, they
work and are worth the money, and will make the job sooooooooooo much
simpler. *Lots of places where sweating is dangerous, can't get in there,
stud's too tight, can't do this or that ..................... SHARK BITE!
Copper to pex to pvc to copper to pex, it all just fits together if the OD
is the same. *It's so simple, it makes stupid people feel guilty. *(Or at
least in my case.)

The repairs are going on three seasons old now, a concern I had of them,
whether or not they'd last. *But even if they just last five years, I'd
happily replace with them again just for the convenience and safety aspect
of the job.

YMMV, and all that stuff ..................

Steve- Hide quoted text -

- Show quoted text -

"Copper to pex to pvc to copper to pex, it all just fits together
if the OD is the same."

SharkBite makes "reducing fittings" so the OD does not have to be the
same.

http://www.sharkbite.com/usa/en/prod...h-fit-fittings

My favorite use of a SharkBite was when I turned off the water to the
house, cut out a section of pipe, slapped a SharkBite cap on the end
of the live section and turned the water back on - all before the
commercial was over and without anyone in the house knowing I had shut
off the water, including my wife who was cooking dinner in the
kitchen.

How to connect copper to PVC?
 

"Steve Barker" wrote


sharkbites don't fit pvc. they fit CPVC.

Whatever. They sure are handy, though. As for the op, I'd get a glue on
NPT PVC, and a compression fit with a mating copper piece.

Steve

How to connect copper to PVC?
 

On Nov 2, 11:57*am, DerbyDad03 wrote:

My favorite use of a SharkBite was when I turned off the water to the
house, cut out a section of pipe, slapped a SharkBite cap on the end
of the live section and turned the water back on - all before the
commercial was over and without anyone in the house knowing I had shut
off the water, including my wife who was cooking dinner in the
kitchen.

Yep. That's one of my favorites. Cut and cap almost as quickly as
talking about it. They're also really useful for shunting water
temporarily while a bathroom or whatever is worked on.

R

How to connect copper to PVC?
 

On Nov 2, 12:37*pm, RicodJour wrote:
On Nov 2, 11:57*am, DerbyDad03 wrote:



My favorite use of a SharkBite was when I turned off the water to the
house, cut out a section of pipe, slapped a SharkBite cap on the end
of the live section and turned the water back on - all before the
commercial was over and without anyone in the house knowing I had shut
off the water, including my wife who was cooking dinner in the
kitchen.

Yep. *That's one of my favorites. *Cut and cap almost as quickly as
talking about it. *They're also really useful for shunting water
temporarily while a bathroom or whatever is worked on.

R

I recall the time before pre-SharkBites that I was trying to sweat a
cap onto a line.

Just as the solder started to flow the cap shot off the end of the
pipe with a POP and flew across the basement, spewing the liquid
solder in its path.

I'm glad no one else was nearby...could have caused injuries.

How to connect copper to PVC?
 

On Nov 2, 3:11*pm, Steve Barker wrote:
On 11/2/2011 10:07 AM, DerbyDad03 wrote:





On Nov 2, 12:37 pm, *wrote:
On Nov 2, 11:57 am, *wrote:

My favorite use of a SharkBite was when I turned off the water to the
house, cut out a section of pipe, slapped a SharkBite cap on the end
of the live section and turned the water back on - all before the
commercial was over and without anyone in the house knowing I had shut
off the water, including my wife who was cooking dinner in the
kitchen.

Yep. *That's one of my favorites. *Cut and cap almost as quickly as
talking about it. *They're also really useful for shunting water
temporarily while a bathroom or whatever is worked on.

R

I recall the time before pre-SharkBites that I was trying to sweat a
cap onto a line.

Just as the solder started to flow the cap shot off the end of the
pipe with a POP and flew across the basement, spewing the liquid
solder in its path.

I'm glad no one else was nearby...could have caused injuries.

you owe me a keyboard. *I just spewed coke all over it LMAO...

--
Steve Barker
remove the "not" from my address to email- Hide quoted text -

- Show quoted text -

I can certainly tell you that it wasn't funny at the time.

It's no fun being startled while standing on a step ladder hold a lit
torch in your hand!

How to connect copper to PVC?
 

On Tue, 01 Nov 2011 21:34:21 -0700, Steve Barker
wrote:

If you don't have the soldering rig, a $7 Sharkbite is less than a burner, a
tank of fuel, solder, flux, and all the other stuff. A lot less.

Steve



sharkbites don't fit pvc. they fit CPVC.


(teach me moment)

Are not PVC / CPVC in the same diameters, etc.? I know CPVC is for
hot water. 1/2 PVC is not the same size as 1/2 CPVC?

Thanks.

How to connect copper to PVC?
 

On 11/2/2011 10:07 AM, DerbyDad03 wrote:
On Nov 2, 12:37 pm, wrote:
On Nov 2, 11:57 am, wrote:



My favorite use of a SharkBite was when I turned off the water to the
house, cut out a section of pipe, slapped a SharkBite cap on the end
of the live section and turned the water back on - all before the
commercial was over and without anyone in the house knowing I had shut
off the water, including my wife who was cooking dinner in the
kitchen.

Yep. That's one of my favorites. Cut and cap almost as quickly as
talking about it. They're also really useful for shunting water
temporarily while a bathroom or whatever is worked on.

R

I recall the time before pre-SharkBites that I was trying to sweat a
cap onto a line.

Just as the solder started to flow the cap shot off the end of the
pipe with a POP and flew across the basement, spewing the liquid
solder in its path.

I'm glad no one else was nearby...could have caused injuries.

you owe me a keyboard. I just spewed coke all over it LMAO...

--
Steve Barker
remove the "not" from my address to email

How to connect copper to PVC?
 

On Tue, 1 Nov 2011 21:29:01 +0000 (UTC), Jules Richardson
wrote:

On Mon, 31 Oct 2011 14:33:50 -0600, jw wrote:
Duct tape and bungie cords are all you will ever need to repair
everything.

Duct tape didn't work when my clothes dryer belt snapped the other day
and nowhere in town had a replacement. I never thought of trying a bungie
cord, though ;-)

A bungie should work fine for your belt, just remove the metal hooks
on the end and duct tape the ends together. Of course you need the
proper length bungie. You can measure that by taking a tail hair off
one of you your cattle or horses. or using a piece of balin twine as a
measurin device. If you aint got none of them things, but are lucky
enough to still have a dollar bill in your wallet in this poor
economy, all dollar bills are 6 inches long. Then measure to the
closest letter or number on the bill if it's an uneven divider of six.
Then you get a bungie thats a little shorter.

How to connect copper to PVC?
 

On Nov 2, 11:52*am, Oren wrote:
On Tue, 01 Nov 2011 21:34:21 -0700, Steve Barker

wrote:
If you don't have the soldering rig, a $7 Sharkbite is less than a burner, a
tank of fuel, solder, flux, and all the other stuff. *A lot less.

Steve

sharkbites don't fit pvc. *they fit CPVC.

(teach me moment)

Are not PVC / CPVC in the same diameters, etc.? *I know CPVC is for
hot water. *1/2 PVC is not the same size as 1/2 CPVC?

Thanks.

No.CPVC is smaller outside diameter. Enough so that the fittings do
not interchange.

Harry K

How to connect copper to PVC?
 

On Wed, 2 Nov 2011 13:21:58 -0700 (PDT), Harry K
wrote:

sharkbites don't fit pvc. *they fit CPVC.

(teach me moment)

Are not PVC / CPVC in the same diameters, etc.? *I know CPVC is for
hot water. *1/2 PVC is not the same size as 1/2 CPVC?

Thanks.

No.CPVC is smaller outside diameter. Enough so that the fittings do
not interchange.

Thanks.

How to connect copper to PVC?
 

With speed like that, you'd have made an excellent civil war
era surgeon. A very fine skill, sir.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"DerbyDad03"
wrote in message
...

"Copper to pex to pvc to copper to pex, it all just fits
together
if the OD is the same."

SharkBite makes "reducing fittings" so the OD does not have
to be the
same.

http://www.sharkbite.com/usa/en/prod...h-fit-fittings

My favorite use of a SharkBite was when I turned off the
water to the
house, cut out a section of pipe, slapped a SharkBite cap on
the end
of the live section and turned the water back on - all
before the
commercial was over and without anyone in the house knowing
I had shut
off the water, including my wife who was cooking dinner in
the
kitchen.

How to connect copper to PVC?
 

On Tue, 01 Nov 2011 21:34:21 -0700, Steve Barker
wrote:

sharkbites don't fit pvc. they fit CPVC.

Skip both and use PEX on the SB to copper.

How to connect copper to PVC?
 

Ouch, that's not good. What could have been done better?
Vent the line some how?

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"DerbyDad03" wrote in message
...

I recall the time before pre-SharkBites that I was trying to
sweat a
cap onto a line.

Just as the solder started to flow the cap shot off the end
of the
pipe with a POP and flew across the basement, spewing the
liquid
solder in its path.

I'm glad no one else was nearby...could have caused
injuries.

How to connect copper to PVC?
 

Some people laugh at America's Funniest Videos, too.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"DerbyDad03" wrote in message
...
On Nov 2, 3:11 pm, Steve Barker
wrote:

I recall the time before pre-SharkBites that I was
trying to sweat a
cap onto a line.

Just as the solder started to flow the cap shot off the
end of the
pipe with a POP and flew across the basement, spewing
the liquid
solder in its path.

I'm glad no one else was nearby...could have caused
injuries.

you owe me a keyboard. I just spewed coke all over it
LMAO...

--
Steve Barker
remove the "not" from my address to email- Hide quoted
text -

- Show quoted text -

I can certainly tell you that it wasn't funny at the time.

It's no fun being startled while standing on a step ladder
hold a lit
torch in your hand!

How to connect copper to PVC?
 

Not same size.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"Oren" wrote in message
...


sharkbites don't fit pvc. they fit CPVC.


(teach me moment)

Are not PVC / CPVC in the same diameters, etc.? I know CPVC
is for
hot water. 1/2 PVC is not the same size as 1/2 CPVC?

Thanks.