basin wrench won't fit, can't remove plastic nuts
I'm trying to change my faucet in the kitchen and I just noticed that
the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? |
basin wrench won't fit, can't remove plastic nuts
yes there is a tool made to fit over the nut I know ridgid makes one. Cone
shapes with notches that fit over those tabs "Joe" wrote in message ... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? |
basin wrench won't fit, can't remove plastic nuts
On Sep 30, 5:03*pm, "Don & Lucille" wrote:
yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message ... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. If you can reach it with your dremel, give it a shot. JK |
basin wrench won't fit, can't remove plastic nuts
On Sep 30, 5:11*pm, Big_Jake wrote:
On Sep 30, 5:03*pm, "Don & Lucille" wrote: yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message ... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. *I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. *If you can reach it with your dremel, give it a shot. JK Just tap the lips with your screwdriver or dremel it off as you can always replace also try needle nose pliers handle ends . |
basin wrench won't fit, can't remove plastic nuts
On Sep 30, 9:05*pm, jim wrote:
On Sep 30, 5:11*pm, Big_Jake wrote: On Sep 30, 5:03*pm, "Don & Lucille" wrote: yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message .... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. *I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. *If you can reach it with your dremel, give it a shot. JK Just tap the lips with your screwdriver or dremel it off as you can always replace also try needle nose pliers handle ends .- Hide quoted text - - Show quoted text - Don't use a torch as it could discoler the stainless steel |
basin wrench won't fit, can't remove plastic nuts
On Sep 30, 10:07 pm, jim wrote:
On Sep 30, 9:05 pm, jim wrote: On Sep 30, 5:11 pm, Big_Jake wrote: On Sep 30, 5:03 pm, "Don & Lucille" wrote: yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message ... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. If you can reach it with your dremel, give it a shot. JK Just tap the lips with your screwdriver or dremel it off as you can always replace also try needle nose pliers handle ends .- Hide quoted text - - Show quoted text - Don't use a torch as it could discoler the stainless steel actually it unscrewed the opposite direction. I was going lefty loosey when it unscrewed right. Never really encountered that before. Is that some kind of plumber trick to get diy'ers to give up? |
basin wrench won't fit, can't remove plastic nuts
On Sep 30, 10:55*pm, Joe wrote:
On Sep 30, 10:07 pm, jim wrote: On Sep 30, 9:05 pm, jim wrote: On Sep 30, 5:11 pm, Big_Jake wrote: On Sep 30, 5:03 pm, "Don & Lucille" wrote: yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message ... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. *I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. *If you can reach it with your dremel, give it a shot. JK Just tap the lips with your screwdriver or dremel it off as you can always replace also try needle nose pliers handle ends .- Hide quoted text - - Show quoted text - Don't use a torch as it could discoler the stainless steel actually it unscrewed the opposite direction. I was going lefty loosey when it unscrewed right. Never really encountered that before. Is that some kind of plumber trick to get diy'ers to give up? No. That is really unusual. Are you sure it wasn't your perspective? What brand is the faucet? JK |
basin wrench won't fit, can't remove plastic nuts
On Oct 2, 1:31*pm, Blattus Slafaly
wrote: Joe wrote: On Sep 30, 10:07 pm, jim wrote: On Sep 30, 9:05 pm, jim wrote: On Sep 30, 5:11 pm, Big_Jake wrote: On Sep 30, 5:03 pm, "Don & Lucille" wrote: yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message .... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. *I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. *If you can reach it with your dremel, give it a shot. JK Just tap the lips with your screwdriver or dremel it off as you can always replace also try needle nose pliers handle ends .- Hide quoted text - - Show quoted text - Don't use a torch as it could discoler the stainless steel actually it unscrewed the opposite direction. I was going lefty loosey when it unscrewed right. Never really encountered that before. Is that some kind of plumber trick to get diy'ers to give up? That is completely unheard of. -- Blattus Slafaly *? 3 * * :) *7/8- Hide quoted text - - Show quoted text - That is completely unheard of. No it's not...I heard it right here, a couple of posts up. ;-) |
basin wrench won't fit, can't remove plastic nuts
On Oct 2, 9:53 am, Big_Jake wrote:
On Sep 30, 10:55 pm, Joe wrote: On Sep 30, 10:07 pm, jim wrote: On Sep 30, 9:05 pm, jim wrote: On Sep 30, 5:11 pm, Big_Jake wrote: On Sep 30, 5:03 pm, "Don & Lucille" wrote: yes there is a tool made to fit over the nut I know ridgid makes one. Cone shapes with notches that fit over those tabs"Joe" wrote in message ... I'm trying to change my faucet in the kitchen and I just noticed that the two nuts holding my faucet to the basin are plastic twist nuts and I cannot budge them with my hand and cannot fit the basin wrench around the nut without hitting the basin. It's a plastic nut with 2 wings. Is there any way to get this thing off outside of taking my dremel tool to it? I have the Ridgid tool, but I have had that not work too. I have used my torch in a pinch, on a stainless sink with a fire extinguisher handy. If you can reach it with your dremel, give it a shot. JK Just tap the lips with your screwdriver or dremel it off as you can always replace also try needle nose pliers handle ends .- Hide quoted text - - Show quoted text - Don't use a torch as it could discoler the stainless steel actually it unscrewed the opposite direction. I was going lefty loosey when it unscrewed right. Never really encountered that before. Is that some kind of plumber trick to get diy'ers to give up? No. That is really unusual. Are you sure it wasn't your perspective? What brand is the faucet? JK Price Pfister. I don't believe it was my perspective, I was looking up at it and going lefty loosey forever until I just started trying to tighten it for some reason and it started loosening. When in installed the new faucet I turned it right to tighten it. |
All times are GMT +1. The time now is 12:17 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter