Paint For Inside Microwave Oven
 

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff
--
Jeffry Wisnia
(W1BSV + Brass Rat '57 EE)
The speed of light is 1.8*10^12 furlongs per fortnight.

Paint For Inside Microwave Oven
 

In article J-ydnfEve7ooLJXVnZ2dnUVZ_j-dnZ2d@choiceonecommunications,
Jeff Wisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff

I'd say if the OEMs coating (powder coating? baked on enamel?) there's
not much chance you'll be successful fixing it for any length of time.
If it weren't for those wheels, maybe. A mag-lev rotary table conversion
kit might help.

Paint For Inside Microwave Oven
 

Jeff Wisnia wrote:
Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers
on the round three wheeled carriage under the rotating glass dish have
been rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area
to improve appearances? Perhaps one of those little brush top bottles
of white appliance touch up paint would do the trick.


White touch-up appliance paint should work. You might try lubricating the
wheels with just a touch of powdered Teflon to minimize future wear.

Paint For Inside Microwave Oven
 

Jeff Wisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff
--
Jeffry Wisnia
(W1BSV + Brass Rat '57 EE)
The speed of light is 1.8*10^12 furlongs per fortnight.

Skip the paint and get some thin UHMW poly sheet to cut a ring of and
glue down as a track for the rollers.

Paint For Inside Microwave Oven
 

Pete C. wrote:

Jeff Wisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff
--
Jeffry Wisnia
(W1BSV + Brass Rat '57 EE)
The speed of light is 1.8*10^12 furlongs per fortnight.


Skip the paint and get some thin UHMW poly sheet to cut a ring of and
glue down as a track for the rollers.


Thanks. That was the first thing I'd thought of, but the "track" is
depressed into the oven bottom and has sloping sides, which are also
missing some paint now, but maybe a ring of poly sheet as you siggest
will take care of the flat surface the wheels roll on and some white
paint will replace what's flaked off the sloping sides.

I think I'll try that..

Jeff

--
Jeffry Wisnia
(W1BSV + Brass Rat '57 EE)
The speed of light is 1.8*10^12 furlongs per fortnight.

Paint For Inside Microwave Oven
 

On Fri, 18 Apr 2008 10:36:56 -0400, Jeff Wisnia
wrote:


Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff


I'd wipe the rusted area with a little cooking oil or shortening and
forget about repair work. Most of my appliances working over 15
years look a little worn too (cooktops, dishwasher racks, dented sink,
etc), but glad they still work fine. Glad Martha S. doesn't live
here.

Paint For Inside Microwave Oven
 

Phisherman wrote:

On Fri, 18 Apr 2008 10:36:56 -0400, Jeff Wisnia
wrote:


Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff



I'd wipe the rusted area with a little cooking oil or shortening and
forget about repair work. Most of my appliances working over 15
years look a little worn too (cooktops, dishwasher racks, dented sink,
etc), but glad they still work fine. Glad Martha S. doesn't live
here.


Your prolly right, I should heed the adage, "Pretty is as pretty does."

Jeff

--
Jeffry Wisnia
(W1BSV + Brass Rat '57 EE)
The speed of light is 1.8*10^12 furlongs per fortnight.

Paint For Inside Microwave Oven
 

Phisherman wrote:

On Fri, 18 Apr 2008 10:36:56 -0400, Jeff Wisnia
wrote:



Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff




I'd wipe the rusted area with a little cooking oil or shortening and
forget about repair work. Most of my appliances working over 15
years look a little worn too (cooktops, dishwasher racks, dented sink,
etc), but glad they still work fine. Glad Martha S. doesn't live
here.


The oil would cook, and possibly burn? Time for a new micro? Don't
know if deep rust will
let microwaves leak, or what hazard that would pose, but they are darn
cheap nowadays.

Paint For Inside Microwave Oven
 

Norminn wrote:

Phisherman wrote:

On Fri, 18 Apr 2008 10:36:56 -0400, Jeff Wisnia
wrote:



Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff




I'd wipe the rusted area with a little cooking oil or shortening and
forget about repair work. Most of my appliances working over 15
years look a little worn too (cooktops, dishwasher racks, dented sink,
etc), but glad they still work fine. Glad Martha S. doesn't live
here.


The oil would cook, and possibly burn? Time for a new micro? Don't
know if deep rust will
let microwaves leak, or what hazard that would pose, but they are darn
cheap nowadays.

Don't know how the oil film would hold up. Only a rust through would let
microwaves out. Cheap for a basic unit, not so cheap if used as an
excuse to upgrade to an Advantium or similar. Of course the old unit
could migrate to the workshop for reheating coffee while working on a
project.

Paint For Inside Microwave Oven
 

clipped

Don't know how the oil film would hold up. Only a rust through would let
microwaves out. Cheap for a basic unit, not so cheap if used as an
excuse to upgrade to an Advantium or similar. Of course the old unit
could migrate to the workshop for reheating coffee while working on a
project.


I started a fire in my microwave once, thawing a loaf of bread and had
forgotten to take off the
metal twist tie. My son asked, "What's burning?" I said, "What do you
mean?" He pointed at
the microwave and the flaming bread wrapper. Very small amount of
flame, and no damage done.
So, that leads me to ask about exposed metal inside the mw.....dangerous?

Paint For Inside Microwave Oven
 

Norminn wrote:

clipped

Don't know how the oil film would hold up. Only a rust through would let
microwaves out. Cheap for a basic unit, not so cheap if used as an
excuse to upgrade to an Advantium or similar. Of course the old unit
could migrate to the workshop for reheating coffee while working on a
project.


I started a fire in my microwave once, thawing a loaf of bread and had
forgotten to take off the
metal twist tie. My son asked, "What's burning?" I said, "What do you
mean?" He pointed at
the microwave and the flaming bread wrapper. Very small amount of
flame, and no damage done.
So, that leads me to ask about exposed metal inside the mw.....dangerous?

Not if used properly. In the early days of microwave ovens they simply
said not to use metal in the microwave, assuming (possibly correctly for
the time) that consumers were not sophisticated enough to understand the
actual restrictions on using metal in a microwave. More recent microwave
oven user manuals and microwave cookbooks give the real instructions,
which mostly amount to: No sharp points and not too close to the oven
walls. I readily use stainless bowls in the microwave and leave spoons
in containers in the microwave without issues. Microwave instructions
and cookbooks also tell you to use aluminum foil to shield thin areas on
foods from overcooking. Your metal twist tie violated the "no sharp
points" rule, concentrated the energy and caused arcing which started
your fire.

Paint For Inside Microwave Oven
 

On Apr 18, 12:37*pm, Phisherman wrote:
On Fri, 18 Apr 2008 10:36:56 -0400, Jeff Wisnia



wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.

The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.

Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.

I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated anyway.

Thanks guys,

Jeff

I'd wipe the rusted area with a little cooking oil or shortening and
forget about repair work. * Most of my appliances working over 15
years look a little worn too (cooktops, dishwasher racks, dented sink,
etc), but glad they still work fine. *Glad Martha S. doesn't live
here.

Jeff-

Phisherman's suggestion of wiping with cooking oil is a good one.
Been using that technique to keep my 1984 Panasonic countertop
microwave from rusting at the rotary tray wheel path.

I clean under the rotating tray every so often. The paint is only
gone on the wheel path so I can only see it when the tray is out.

I was thinking about painting but figured the paint wouldn't hold up,
plus the light oil rub has prevented any rust damage.

cheers
Bob

Paint For Inside Microwave Oven
 

replying to Jeff Wisnia, Michael wrote:
jwisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.
The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.
Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.
I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated
anyway.
Thanks guys,
Jeff



I think you're right to be concerned about exposed metal on the inside of
your microwave, primarily because of possible electrical arcing and
secondarily because of aesthetics There are several glossy, enamel paint
products available that are designed to cover exposed metal and make
things look better, too. Some of the paints come in a small tube with an
applicator, like car touch-up paint. Check around online or call a local
appliance parts/repair place since markups vary widely. Oil will work its
way underneath the margins of your current wearline and cook, which may
likely exacerbate your current problem. Powdered teflon might be okay for
ongoing friction, but I would never use it unless people with chemistry
and medical expertise could assure me that it's not carcinogenic,
especially in a microwave where we prepare food at high heat to be
ingested. Sheesh, we're not even supposed to cook in plastic, so there's
no way I'm using teflon in there. Be sure to follow directions with the
paint, including thorough shaking of the paint and cleaning the surface
thoroughly of anything greasy or wet so that the paint will adhere.

--
posted from
http://www.homeownershub.com/mainten...en-301244-.htm
using HomeOwnersHub's Web, RSS and Social Media Interface
to home and garden related groups

Paint For Inside Microwave Oven
 

Michael wrote:
replying to Jeff Wisnia, Michael wrote:
jwisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers
on the round three wheeled carriage under the rotating glass dish have
been rolling over it for a few years now.
The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.
Anone know what paint(s) are suitable for brushing over the worn area
to improve appearances? Perhaps one of those little brush top bottles
of white appliance touch up paint would do the trick.
I'm thinking that because the paint is right up against a metal
surface it probably can't absorb much of the microwave energy and get
heated
anyway.
Thanks guys,
Jeff



I think you're right to be concerned about exposed metal on the inside of
your microwave, primarily because of possible electrical arcing and
secondarily because of aesthetics There are several glossy, enamel paint
products available that are designed to cover exposed metal and make
things look better, too. Some of the paints come in a small tube with an
applicator, like car touch-up paint. Check around online or call a local
appliance parts/repair place since markups vary widely. Oil will work its
way underneath the margins of your current wearline and cook, which may
likely exacerbate your current problem. Powdered teflon might be okay for
ongoing friction, but I would never use it unless people with chemistry
and medical expertise could assure me that it's not carcinogenic,
especially in a microwave where we prepare food at high heat to be
ingested. Sheesh, we're not even supposed to cook in plastic, so there's
no way I'm using teflon in there. Be sure to follow directions with the
paint, including thorough shaking of the paint and cleaning the surface
thoroughly of anything greasy or wet so that the paint will adhere.


From homeowners hub.
posted on
April 18, 2008, 10:36 am

--
Bill
In Hamptonburgh, NY
In the original Orange County. Est. 1683
To email, remove the double zeros after @

Paint For Inside Microwave Oven
 

"Michael" wrote in
message oups.com...
replying to Jeff Wisnia, Michael wrote:
jwisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.
The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I see
it.
Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.
I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated
anyway.
Thanks guys,
Jeff


SNIP --

posted from
http://www.homeownershub.com/mainten...en-301244-.htm
using HomeOwnersHub's Web, RSS and Social Media Interface
to home and garden related groups

Seems like this is a question to pose to GE. Try the GE Answer Center
1-800-626-2005. Check for the hours that they're open.

Tomsic

Paint For Inside Microwave Oven
 

On Sat, 19 Oct 2013 16:44:02 +0000, Michael
wrote:

replying to Jeff Wisnia, Michael wrote:
jwisnia wrote:

Our kitchen's GE microwave oven is still working fine, but the white
paint on the oven floor is cracked and peeling off where the rollers on
the round three wheeled carriage under the rotating glass dish have been
rolling over it for a few years now.
The bare steel is exposed and getting slightly rusted and the peeling
paint trail is widening. Its appearance mildly annoys me every time I
see it.
Anone know what paint(s) are suitable for brushing over the worn area to
improve appearances? Perhaps one of those little brush top bottles of
white appliance touch up paint would do the trick.
I'm thinking that because the paint is right up against a metal surface
it probably can't absorb much of the microwave energy and get heated
anyway.
Thanks guys,
Jeff



I think you're right to be concerned about exposed metal on the inside of
your microwave, primarily because of possible electrical arcing and

I had a microwave with nothing but metal walls, ceiling, and floor.
No paint at all. I don't think arcing is a problem here. He can
check further by removing the dish and the trivet and warming a cup of
water. I'll bet there will still be no arcing. Uncovering more of
the metal won't make it worse.

The walls are not hot, even when cooking, which is why one can clean a
microwave just by boiling water in it. Food dries on but does not get
"cooked on". Just cook something and then touch the wall or the the
place on the floor with no paint, and you'll see it's not hot.

Only polar molecules are heated, and I gather it's only the polar
molecules with a resonant frequency the same as the oven's. That is,
water.

secondarily because of aesthetics There are several glossy, enamel paint
products available that are designed to cover exposed metal and make
things look better, too. Some of the paints come in a small tube with an
applicator, like car touch-up paint. Check around online or call a local
appliance parts/repair place since markups vary widely. Oil will work its
way underneath the margins of your current wearline and cook, which may
likely exacerbate your current problem. Powdered teflon might be okay for
ongoing friction, but I would never use it unless people with chemistry
and medical expertise could assure me that it's not carcinogenic,
especially in a microwave where we prepare food at high heat to be
ingested. Sheesh, we're not even supposed to cook in plastic, so there's
no way I'm using teflon in there. Be sure to follow directions with the
paint, including thorough shaking of the paint and cleaning the surface
thoroughly of anything greasy or wet so that the paint will adhere.

Paint For Inside Microwave Oven
 

On Sun, 20 Oct 2013 13:09:06 -0400, micky
wrote:


I had a microwave with nothing but metal walls, ceiling, and floor.
No paint at all. I don't think arcing is a problem here. He can
check further by removing the dish and the trivet and warming a cup of
water. I'll bet there will still be no arcing. Uncovering more of
the metal won't make it worse.

The walls are not hot, even when cooking, which is why one can clean a
microwave just by boiling water in it. Food dries on but does not get
"cooked on". Just cook something and then touch the wall or the the
place on the floor with no paint, and you'll see it's not hot.

Only polar molecules are heated, and I gather it's only the polar
molecules with a resonant frequency the same as the oven's. That is,
water.

But even with water and the food that contains it, the food splattered
on the walls and floor doesn't get heated.

Paint For Inside Microwave Oven
 

On Friday, April 18, 2008 9:36:56 AM UTC-5, Jeff Wisnia wrote:
Our kitchen's GE microwave oven is still working fine, but the white paint on the oven floor is cracked and peeling off where the rollers on the round three wheeled carriage under the rotating glass dish have been rolling over it for a few years now.The bare steel is exposed and getting slightly rusted and the peeling paint trail is widening. Its appearance mildly annoys me every time I see it.Anone know what paint(s) are suitable for brushing over the worn area to improve appearances? Perhaps one of those little brush top bottles of white appliance touch up paint would do the trick.I'm thinking that because the paint is right up against a metal surface it probably can't absorb much of the microwave energy and get heated anyway. Thanks guys,Jeff-- Jeffry Wisnia (W1BSV + Brass Rat '57 EE) The speed of light is 1.8*10^12 furlongs per fortnight.

I would just go with a good epoxy paint, or maybe even just a good Rustoleum spray paint. HEAT is not an issue, only wearability.

Paint For Inside Microwave Oven
 

Spray paint is the way to go. Rustoleum. Clean it well and dry before spraying.