load center and branch wiring detail
 

I'm getting ready to hang a 200A load center and also connect up a
100A disconnect.

At thge load center location the two branch circuits are coming out of
the side of the structure which has vinyl siding over wood. one of the
branch circuits is currently connected to the old 100A meter.
on the bottom back of the new load center there are two knockout s for
wires one on each corner.
my two branch circuits are SER4/4/4/2 cable one above the other about
two inches apart, and I'd like to feed them into the load center
through the back so there is no exposed wire.
So the question is what are some approved ways of doing this?

can i knock out the knock out then drill another hole adjacent to it
so i have a figure 8 opening? or make one big round hole? the wires
are about .75" diameter. the spacing is about 2.625 center to center,
and the overall hole diameter would need to be a clear 3.5" Don't they
need to be clamped? (they're already weather sealed.
I want the panel to sit tight up to the mounting surface. the other
question is the SER into the disconnect. for the sake of neatness and
safety I want to lay the incoming and outgoing wires flat against the
side of the box, but the onlt connectors my supply house has are
straight ones. FOr lighter gauge romex there are 90 degree connectors,
but my guy says he is unaware of such a connector for this size wire.

load center and branch wiring detail
 

I've read it three times, and I'm still not sure what you're trying to do.
What's feeding the new 200 amp panel? Do you have two 100 amp loads that you
want fed from this new panel? I've never seen SER 4442, and if it were made,
as a feeder, it would only be good for about 70 amps, assuming it's aluminum



"timO'" wrote in message
oups.com...
I'm getting ready to hang a 200A load center and also connect up a
100A disconnect.

At thge load center location the two branch circuits are coming out of
the side of the structure which has vinyl siding over wood. one of the
branch circuits is currently connected to the old 100A meter.
on the bottom back of the new load center there are two knockout s for
wires one on each corner.
my two branch circuits are SER4/4/4/2 cable one above the other about
two inches apart, and I'd like to feed them into the load center
through the back so there is no exposed wire.
So the question is what are some approved ways of doing this?

can i knock out the knock out then drill another hole adjacent to it
so i have a figure 8 opening? or make one big round hole? the wires
are about .75" diameter. the spacing is about 2.625 center to center,
and the overall hole diameter would need to be a clear 3.5" Don't they
need to be clamped? (they're already weather sealed.
I want the panel to sit tight up to the mounting surface. the other
question is the SER into the disconnect. for the sake of neatness and
safety I want to lay the incoming and outgoing wires flat against the
side of the box, but the onlt connectors my supply house has are
straight ones. FOr lighter gauge romex there are 90 degree connectors,
but my guy says he is unaware of such a connector for this size wire.

load center and branch wiring detail
 

"timO'" wrote in message
oups.com...
I'm getting ready to hang a 200A load center and also connect up a
100A disconnect.

At thge load center location the two branch circuits are coming out of
the side of the structure which has vinyl siding over wood. one of the
branch circuits is currently connected to the old 100A meter.
on the bottom back of the new load center there are two knockout s for
wires one on each corner.
my two branch circuits are SER4/4/4/2 cable one above the other about
two inches apart, and I'd like to feed them into the load center
through the back so there is no exposed wire.
So the question is what are some approved ways of doing this?


You need two knockouts in the back that will each take an appropriately
sized SER connector (1" 0r 1 1/4"?). Put bushings on the connectors. You
will probably need to enlarge the holes in the house where your feeder
cables are coming out of to move them to the knockout locations. Use a hole
saw or knockout punch to make your holes in the load center if there are no
pre-punched KO's where you want them. Don't make them too close together.
You cannot just bring the cables into the back of the loadcenter without
connectors. Shouldn't your cable be 2/2/4/6 if you are using copper for 100
amps?



can i knock out the knock out then drill another hole adjacent to it
so i have a figure 8 opening? or make one big round hole? the wires
are about .75" diameter. the spacing is about 2.625 center to center,
and the overall hole diameter would need to be a clear 3.5" Don't they
need to be clamped? (they're already weather sealed.
I want the panel to sit tight up to the mounting surface.


See above


the other question is the SER into the disconnect. for the sake of neatness
and
safety I want to lay the incoming and outgoing wires flat against the
side of the box, but the onlt connectors my supply house has are
straight ones. FOr lighter gauge romex there are 90 degree connectors,
but my guy says he is unaware of such a connector for this size wire.


I'm not sure what you are trying to do here. Is this an outdoor disconnect?

load center and branch wiring detail
 

On Sat, 14 Jul 2007 17:07:09 -0000, timO'
wrote:

I'm getting ready to hang a 200A load center

and also connect up a
100A disconnect.

Are you sure you can connect a disconnect? That seems like reviving
the dead or squaring a circle.

load center and branch wiring detail
 

timO' wrote:
I'm getting ready to hang a 200A load center and also connect up a
100A disconnect.

At thge load center location the two branch circuits are coming out of
the side of the structure which has vinyl siding over wood. one of the
branch circuits is currently connected to the old 100A meter.
on the bottom back of the new load center there are two knockout s for
wires one on each corner.
my two branch circuits are SER4/4/4/2 cable one above the other about
two inches apart, and I'd like to feed them into the load center
through the back so there is no exposed wire.
So the question is what are some approved ways of doing this?

can i knock out the knock out then drill another hole adjacent to it
so i have a figure 8 opening? or make one big round hole? the wires
are about .75" diameter. the spacing is about 2.625 center to center,
and the overall hole diameter would need to be a clear 3.5" Don't they
need to be clamped? (they're already weather sealed.
I want the panel to sit tight up to the mounting surface. the other
question is the SER into the disconnect. for the sake of neatness and
safety I want to lay the incoming and outgoing wires flat against the
side of the box, but the onlt connectors my supply house has are
straight ones. FOr lighter gauge romex there are 90 degree connectors,
but my guy says he is unaware of such a connector for this size wire.


The terms you are using are causing me some confusion. Is the item you
are calling a load center the meter enclosure? If yes then you cannot
cut additional holes in it. Some utilities will not allow the service
conductors to be run through the back of a meter enclosure. If what you
are referring to is a Combination meter enclosure and service
disconnecting means then that may not apply to it. Provide the make and
the model number of the device you are talking about and I can be of
more help.
--
Tom Horne

"This alternating current stuff is just a fad. It is much too dangerous
for general use." Thomas Alva Edison