Switch + Receptacle thru to Receptacle
 

Need an idea how to wire a switch (controlling a light) off of a
receptacle passing through to another receptacle. I have the
following wires coming into a double gang box holding a receptacle and
a single pole switch:

A. Black - from panel
B. White - from panel
C. Ground - from panel

D. Black - to another receptacle
E. White - to another receptacle
F. Ground - to another receptacle

G. Black - to Light
H. White - to Light
I. Ground - to Light

RecHot1
RecHot2
RecNeu1
RecNeu2
RecGnd

Sw1
Sw2

BoxGnd1
BoxGnd2
BoxGnd3 - i assume it has 3...

I was thinking the following...

A--RecHot1--Sw1 (wire nut w/ 2 jumpers)
B--RecNeu1--H (wire nut w/ 1 jumper)
C--RecGnd--BoxGnd1 (wire nut w/ 2 jumpers)

D -- RecHot2
E -- RecNeu2
F -- BoxGnd2

G -- Sw2
I -- BoxGnd3

Does that sound right?

Switch + Receptacle thru to Receptacle
 

Wherever you get the feed from, you need a constant hot, neutral, and
ground. The neutral and ground go directly to the light being controlled,
and the hot leg is broken by the switch



"RymCo" wrote in message
ps.com...
Need an idea how to wire a switch (controlling a light) off of a
receptacle passing through to another receptacle. I have the
following wires coming into a double gang box holding a receptacle and
a single pole switch:

A. Black - from panel
B. White - from panel
C. Ground - from panel

D. Black - to another receptacle
E. White - to another receptacle
F. Ground - to another receptacle

G. Black - to Light
H. White - to Light
I. Ground - to Light

RecHot1
RecHot2
RecNeu1
RecNeu2
RecGnd

Sw1
Sw2

BoxGnd1
BoxGnd2
BoxGnd3 - i assume it has 3...

I was thinking the following...

A--RecHot1--Sw1 (wire nut w/ 2 jumpers)
B--RecNeu1--H (wire nut w/ 1 jumper)
C--RecGnd--BoxGnd1 (wire nut w/ 2 jumpers)

D -- RecHot2
E -- RecNeu2
F -- BoxGnd2

G -- Sw2
I -- BoxGnd3

Does that sound right?

Switch + Receptacle thru to Receptacle
 

RymCo wrote:
Need an idea how to wire a switch (controlling a light) off of a
receptacle passing through to another receptacle. I have the
following wires coming into a double gang box holding a receptacle and
a single pole switch:

A. Black - from panel
B. White - from panel
C. Ground - from panel

D. Black - to another receptacle
E. White - to another receptacle
F. Ground - to another receptacle

G. Black - to Light
H. White - to Light
I. Ground - to Light

RecHot1
RecHot2
RecNeu1
RecNeu2
RecGnd

Sw1
Sw2

BoxGnd1
BoxGnd2
BoxGnd3 - i assume it has 3...

I was thinking the following...

A--RecHot1--Sw1 (wire nut w/ 2 jumpers)
B--RecNeu1--H (wire nut w/ 1 jumper)
C--RecGnd--BoxGnd1 (wire nut w/ 2 jumpers)

D -- RecHot2
E -- RecNeu2
F -- BoxGnd2

G -- Sw2
I -- BoxGnd3

Does that sound right?

Based on the simplicity of the answer here, you should not be doing this
yourself; get assistance in.

Pop`

Switch + Receptacle thru to Receptacle
 

I did not try to follow your explanation.

The big issue is how to switch the light. There are two methods
of getting a light to work. You need to figure out which one you
do have. If you do not understand this completely, get an
electrician!!

Method one. A colored hot and white neutral to the light. A
chunk of Romex with a white/black/bare that is used as a switch
leg to the switch you flip. The chunk of Romex interrupts the
colored hot between panel and light fixture. The chunk of Romex
makes both the black and the white hot leads, the black on one
screw of the switch/white on the other interrupting the hot of the
light.

Method two. A colored hot and a white neutral to the switch. A
hot going through the switch to the light. A neutral going
through the box to the light.

All greens and bares wire together.
Each recep needs a hot and a neutral.
Each light needs a hot and a neutral.
These hots and neutrals do not have to be different circuits,
though it is nice to have lights on one and receps on another.
Load requirements may demand separate receptacle circuits.
You need to interrupt the hot going to a light with a switch.

--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)




"RymCo" wrote in message
ps.com...
Need an idea how to wire a switch (controlling a light) off of a
receptacle passing through to another receptacle. I have the
following wires coming into a double gang box holding a
receptacle and
a single pole switch:

A. Black - from panel
B. White - from panel
C. Ground - from panel

D. Black - to another receptacle
E. White - to another receptacle
F. Ground - to another receptacle

G. Black - to Light
H. White - to Light
I. Ground - to Light

RecHot1
RecHot2
RecNeu1
RecNeu2
RecGnd

Sw1
Sw2

BoxGnd1
BoxGnd2
BoxGnd3 - i assume it has 3...

I was thinking the following...

A--RecHot1--Sw1 (wire nut w/ 2 jumpers)
B--RecNeu1--H (wire nut w/ 1 jumper)
C--RecGnd--BoxGnd1 (wire nut w/ 2 jumpers)

D -- RecHot2
E -- RecNeu2
F -- BoxGnd2

G -- Sw2
I -- BoxGnd3

Does that sound right?