How to hang pine wall planking
 

I finished framing my basement with 2x4's. Electrical, insulation, and
vapor barrier is installed. I plan on finishing the walls with 8"
wide tongue & groove wall planking, The planks will be horizontal
across the studs. I plan on using an air nailer to nail the 8inch
wide 8foot long planks to the studs through the tongue of the planks

Any advice relative to my installation? How far off the floor should I
start? How to you handle the joints at the ends of the planks? I
assume you don't just butt them together. Should the end joints of
the boards be staggered? If so, what's the best way to do that?

Thanks,
Kevin

How to hang pine wall planking
 

" wrote in message
Any advice relative to my installation? How far off the floor should I
start?


Is the basement dry? Allow at least an inch on the bottom, more if you've
ever had water.

How to you handle the joints at the ends of the planks? I
assume you don't just butt them together.

YOu can, but look up "shiplap joints" for better appearance.

Should the end joints of
the boards be staggered? If so, what's the best way to do that?

Start at one end of the wall and work to the other. The last board will
have to be cut to fit. Use that board to start the next row. To keep it
random, cut a board for the third row. If the first piece was say 16", cut
off the next as 48" to give a better stagger. Or use them on an adjacent
wall to stagger that. IMO, random look better than a symmetrical joint.

How to hang pine wall planking
 

Thanks for your feedback. The basement is dry.


Don't you mean scarf joint rather than shiplap joint?

http://en.wikipedia.org/wiki/Shiplap

http://en.wikipedia.org/wiki/Scarf_joint

Any suggestions as to the wall plank thickness? A lot of the stuff
I'm seeing is pretty thick...seems like over-kill but some of this
think stuff I've seen looks cheap & crappy...


Thanks,
Kevin


Edwin Pawlowski wrote:
" wrote in message
Any advice relative to my installation? How far off the floor should I
start?


Is the basement dry? Allow at least an inch on the bottom, more if you've
ever had water.

How to you handle the joints at the ends of the planks? I
assume you don't just butt them together.

YOu can, but look up "shiplap joints" for better appearance.

Should the end joints of
the boards be staggered? If so, what's the best way to do that?

Start at one end of the wall and work to the other. The last board will
have to be cut to fit. Use that board to start the next row. To keep it
random, cut a board for the third row. If the first piece was say 16", cut
off the next as 48" to give a better stagger. Or use them on an adjacent
wall to stagger that. IMO, random look better than a symmetrical joint.

How to hang pine wall planking
 

On 1 Nov 2006 16:50:30 -0800, "
wrote:

I finished framing my basement with 2x4's. Electrical, insulation, and
vapor barrier is installed. I plan on finishing the walls with 8"
wide tongue & groove wall planking, The planks will be horizontal
across the studs. I plan on using an air nailer to nail the 8inch
wide 8foot long planks to the studs through the tongue of the planks

Any advice relative to my installation? How far off the floor should I
start? How to you handle the joints at the ends of the planks? I
assume you don't just butt them together. Should the end joints of
the boards be staggered? If so, what's the best way to do that?

If you can, pick boards that are long enough to span the room
without joints. Why are you choosing 8' planks?

How to hang pine wall planking
 

Hey, anything besides sheet paneling is overkill for a basement in my
book, but it's all in the eye of the beholder.

Scarf joints are used in baseboards, to make a neat joint that allows
for expansion and contraction without showing a gap. Don't forget to
finish the mitered end of the board before installing, so that if/when
in contracts and a little band of the cut area shows, it will match the
surface wood and thus be inconspicuous.

Come to think of it, getting an accurate miter on 8-inch-wide stock
might be a little tricky, will it fit in your miter saw? -- H


wrote:
Thanks for your feedback. The basement is dry.


Don't you mean scarf joint rather than shiplap joint?

http://en.wikipedia.org/wiki/Shiplap

http://en.wikipedia.org/wiki/Scarf_joint

Any suggestions as to the wall plank thickness? A lot of the stuff
I'm seeing is pretty thick...seems like over-kill but some of this
think stuff I've seen looks cheap & crappy...


Thanks,
Kevin


Edwin Pawlowski wrote:
" wrote in message
Any advice relative to my installation? How far off the floor should I
start?


Is the basement dry? Allow at least an inch on the bottom, more if you've
ever had water.

How to you handle the joints at the ends of the planks? I
assume you don't just butt them together.

YOu can, but look up "shiplap joints" for better appearance.

Should the end joints of
the boards be staggered? If so, what's the best way to do that?

Start at one end of the wall and work to the other. The last board will
have to be cut to fit. Use that board to start the next row. To keep it
random, cut a board for the third row. If the first piece was say 16", cut
off the next as 48" to give a better stagger. Or use them on an adjacent
wall to stagger that. IMO, random look better than a symmetrical joint.

How to hang pine wall planking
 

" wrote in message
oups.com...
Thanks for your feedback. The basement is dry.


Don't you mean scarf joint rather than shiplap joint?

http://en.wikipedia.org/wiki/Shiplap

http://en.wikipedia.org/wiki/Scarf_joint

Yes, brain thought scarf, fingers typed shiplap.

How to hang pine wall planking
 

Thanks guys. I'm using the 8' planking because it's easy to get in my
basement and do a little at a time. Plus I like the look of the
planks.

Thanks,
Kevin