Repairing a tin roof
 

I have a large carport about 20 feet wide. It has 2X8's spaced 2' apart with
2X4's crossing them at 4' intervals. The tin is regular corrugated roofing
and is on top of the 2X4's. Problem is the nails are all coming up. They are
aluminum nails with a rubber washer. I need to get on top of the tin to
repair it. Was thinking of putting some 1/2" plywood on top of the tin and
trying to walk on it. Then I decided to ask and avoid a neck breaking
experience:)

For what it's worth, on the bottom of the 2X8 rafters are some 2X4's nailed
to keep the 2X8's from twisting?? I guess that's why there are there. They
are on 8' centers, the highest one is just over 10' off the ground. Was
thinking of trying to prop up a few of the 2X8's using the 2X4's as stops to
hold the top of the prop and just wedging the other end into the ground. The
2X8's are supported at one end by the building and at the other by some 4X4
posts with two 2X8's bolted together running between them. Seems stout. The
2X4's under the tin are worrying me.

So, what do I do? And, what do I replace the nails with?

Al

Repairing a tin roof
 

Big Al wrote:

How big are you Al? I walk my 250+ lbs around on a similar roof, the
biggest problem I have is causing dents. I walk around with a broom
stick & bang them out after I get down. As to fasteners, I use hex
head, rubber washer screws intended for screwing into wood (Lowe's or
Home Depot) & run them with a cordless drill with a hex tip. The
hardest part is getting the nails completely out.

Repairing a tin roof
 

"Eric in North TX" wrote in message
oups.com...

Big Al wrote:

How big are you Al? I walk my 250+ lbs around on a similar roof, the
biggest problem I have is causing dents. I walk around with a broom
stick & bang them out after I get down. As to fasteners, I use hex
head, rubber washer screws intended for screwing into wood (Lowe's or
Home Depot) & run them with a cordless drill with a hex tip. The
hardest part is getting the nails completely out.


200 pounds. I find it hard to believe the roof can hold you up if it's built
like mine. How long are the screws and what are they called? Bought some
#10, 1.5 inch long Phillips head sheet metal screws toady and some fender
washers. This roof will never hold water but I'd like to stop water from
rotting out the wood.

Al

Repairing a tin roof
 

Look he http://www.trufast.com/
click products then scroll to panel to wood.

I'm careful only to step where the fasteners are, and therefore a
support underneath.
disclaimer: your results my vary, void where prohibited, following my
advice could lead to serious injury, if this is a concern, do not.

Repairing a tin roof
 

On Wed, 13 Sep 2006 23:44:36 -0700, "Big Al" wrote:


"Eric in North TX" wrote in message
roups.com...

Big Al wrote:

How big are you Al? I walk my 250+ lbs around on a similar roof, the
biggest problem I have is causing dents. I walk around with a broom
stick & bang them out after I get down. As to fasteners, I use hex
head, rubber washer screws intended for screwing into wood (Lowe's or
Home Depot) & run them with a cordless drill with a hex tip. The
hardest part is getting the nails completely out.


200 pounds. I find it hard to believe the roof can hold you up if it's built
like mine. How long are the screws and what are they called? Bought some
#10, 1.5 inch long Phillips head sheet metal screws toady and some fender
washers. This roof will never hold water but I'd like to stop water from
rotting out the wood.


If it bothers you you can always lay a ladder across the roof, and
move around on that. It will slow you down quite a bit, though.

Repairing a tin roof
 

On Wed, 13 Sep 2006 23:44:36 -0700, "Big Al" wrote:


"Eric in North TX" wrote in message
roups.com...

Big Al wrote:

How big are you Al? I walk my 250+ lbs around on a similar roof, the
biggest problem I have is causing dents. I walk around with a broom
stick & bang them out after I get down. As to fasteners, I use hex
head, rubber washer screws intended for screwing into wood (Lowe's or
Home Depot) & run them with a cordless drill with a hex tip. The
hardest part is getting the nails completely out.


200 pounds. I find it hard to believe the roof can hold you up if it's built
like mine. How long are the screws and what are they called? Bought some
#10, 1.5 inch long Phillips head sheet metal screws toady and some fender
washers. This roof will never hold water but I'd like to stop water from
rotting out the wood.

Al


Al

You will NEVER hold water with sheet metal screws and fender washers.
You CAN make it leakproof. I'm a farmer and work with tin roofs all
the time. On an old barn I take a caulking gun with silicone caulk,
apply a blob of silicone around every loose nail (under the head), and
slam it tight. Then cover EVERY nail head with this came caulk. You
wont leak unless you got rust holes in the tin. Of course be sure to
remove all junk and dirt before you start. Use push broom and hose,
let it dry, then do the job.

However, you can do even better. Get NEO-NAILS (neoprene washer
nails), get some longer than what you have now. Better yet,
NEO-SCREWS (hex head neoprene washer screws). Add some new ones if
needed and replace all loose ones. Still caulk with silicone all the
original heads, right over the head and extend onto surrounding tin
for 1/4" or so.

To walk on roof, jsut stay on the lumber underneath, or use 2x8 walk
boards.

DO NOT USE THE SHEET METAL SCREWS

Mark

Repairing a tin roof
 

wrote in message
...
On Wed, 13 Sep 2006 23:44:36 -0700, "Big Al" wrote:


"Eric in North TX" wrote in message
roups.com...

Big Al wrote:

How big are you Al? I walk my 250+ lbs around on a similar roof, the
biggest problem I have is causing dents. I walk around with a broom
stick & bang them out after I get down. As to fasteners, I use hex
head, rubber washer screws intended for screwing into wood (Lowe's or
Home Depot) & run them with a cordless drill with a hex tip. The
hardest part is getting the nails completely out.


200 pounds. I find it hard to believe the roof can hold you up if it's
built
like mine. How long are the screws and what are they called? Bought some
#10, 1.5 inch long Phillips head sheet metal screws toady and some fender
washers. This roof will never hold water but I'd like to stop water from
rotting out the wood.

Al


Al

You will NEVER hold water with sheet metal screws and fender washers.
You CAN make it leakproof. I'm a farmer and work with tin roofs all
the time. On an old barn I take a caulking gun with silicone caulk,
apply a blob of silicone around every loose nail (under the head), and
slam it tight. Then cover EVERY nail head with this came caulk. You
wont leak unless you got rust holes in the tin. Of course be sure to
remove all junk and dirt before you start. Use push broom and hose,
let it dry, then do the job.

However, you can do even better. Get NEO-NAILS (neoprene washer
nails), get some longer than what you have now. Better yet,
NEO-SCREWS (hex head neoprene washer screws). Add some new ones if
needed and replace all loose ones. Still caulk with silicone all the
original heads, right over the head and extend onto surrounding tin
for 1/4" or so.

To walk on roof, jsut stay on the lumber underneath, or use 2x8 walk
boards.

DO NOT USE THE SHEET METAL SCREWS

Mark

Thanks Mark. I'll let you know what hospital I end up in:)

Al