drywall corners opening up
 

Over the seven years we have been in the house, all of the exterior
vertical corners in my house have opened up about 1/16" or more in the
middle part of the corner (starting about 18" up from the floor and
extending to about 18" short of the ceiling). The framing is 2x6, of
course. Because of the layout of the house, there are three such
corners in the house; there are two corners in the attached garage,
which is 2x4 construction, and these corners have not cracked to any
significant degree. None of the interior partition corners, nor corners
where partitions meet the exterior walls, have opened up. Two
possibilities occur to me: the nature of an exterior corner post
assembly is different from other corners, and 2x6 lumber moves 60%
farther under moisture changes than does 2x4 lumber.

So, what is likely going on with these corners, and what might I have
done with the drywall to prevent this? By now, probably not much can be
done to fix it, since the corners open and close with the seasons to
some extent (it will be less noticeable when summer humidity and heat
return). I am going to clean out and fill the three corners with
flexible white caulk, but I expect there will still be some cracking, at
least of the paint layer.

drywall corners opening up
 

donald girod wrote:
Over the seven years we have been in the house, all of the exterior
vertical corners in my house have opened up about 1/16" or more in the
middle part of the corner (starting about 18" up from the floor and
extending to about 18" short of the ceiling). The framing is 2x6, of
course. Because of the layout of the house, there are three such
corners in the house; there are two corners in the attached garage,
which is 2x4 construction, and these corners have not cracked to any
significant degree. None of the interior partition corners, nor
corners where partitions meet the exterior walls, have opened up. Two
possibilities occur to me: the nature of an exterior corner post
assembly is different from other corners, and 2x6 lumber moves 60%
farther under moisture changes than does 2x4 lumber.

So, what is likely going on with these corners, and what might I have
done with the drywall to prevent this? By now, probably not much can
be done to fix it, since the corners open and close with the seasons
to some extent (it will be less noticeable when summer humidity and
heat return). I am going to clean out and fill the three corners with
flexible white caulk, but I expect there will still be some cracking,
at least of the paint layer.

I am not sure what you mean by exterior corners, but I am going to
suggest that the drywall was not properly installed using standard
procedures. Each outside corner should have had a metal or plastic corner
bead

http://www.acehardware.com/product/i...ductId=1290770

--
Joseph Meehan

Dia duit

drywall corners opening up
 

I suspect you are seeing the results of normal shrinkage of
framing lumber, it is just compounded by the 2x6 framing. Rather
than re tape and bed the corner, I would wipe the corner in with
painter's latex caulk at the next paint job. Lumber shrinks
across the grain exponentially as compared to with the grain.
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)




"donald girod" wrote in message
...
Over the seven years we have been in the house, all of the
exterior vertical corners in my house have opened up about 1/16"
or more in the middle part of the corner (starting about 18" up
from the floor and extending to about 18" short of the ceiling).
The framing is 2x6, of course. Because of the layout of the
house, there are three such corners in the house; there are two
corners in the attached garage, which is 2x4 construction, and
these corners have not cracked to any significant degree. None
of the interior partition corners, nor corners where partitions
meet the exterior walls, have opened up. Two possibilities
occur to me: the nature of an exterior corner post assembly is
different from other corners, and 2x6 lumber moves 60% farther
under moisture changes than does 2x4 lumber.

So, what is likely going on with these corners, and what might I
have done with the drywall to prevent this? By now, probably
not much can be done to fix it, since the corners open and close
with the seasons to some extent (it will be less noticeable when
summer humidity and heat return). I am going to clean out and
fill the three corners with flexible white caulk, but I expect
there will still be some cracking, at least of the paint layer.

drywall corners opening up
 

By "exterior corner" I mean the corners of the exterior walls of the
house--these are, of course, interior (cove) corners of the drywall.
Anyway, lumber shrinks from moisture loss just twice as much radially as
it does tangentially, but of course almost not at all lengthwise (it
does expand and contract lengthwise to a measurable degree with
temperature changes). A 2x6 should shrink .1", 5.5" to 5.4" going from
19% to 12% moisture content, and I suppose that is what is causing the
trouble. I intend to put acrylic caulk in the crack when I paint.

drywall corners opening up
 

This sounds more like a framing problems than a drywalling problem or a
problem with shrinkage. Properly built corners inside or outside - as in
whether they'd be taped (inside) or beaded (outside), or internal (walls
interal to the house) or external (an outside wall) should not crack as
you've defined, whether made of 2x4 or 2x6.


"donald girod" wrote in message
...
Over the seven years we have been in the house, all of the exterior
vertical corners in my house have opened up about 1/16" or more in the
middle part of the corner (starting about 18" up from the floor and
extending to about 18" short of the ceiling). The framing is 2x6, of
course. Because of the layout of the house, there are three such corners
in the house; there are two corners in the attached garage, which is 2x4
construction, and these corners have not cracked to any significant
degree. None of the interior partition corners, nor corners where
partitions meet the exterior walls, have opened up. Two possibilities
occur to me: the nature of an exterior corner post assembly is different
from other corners, and 2x6 lumber moves 60% farther under moisture
changes than does 2x4 lumber.

So, what is likely going on with these corners, and what might I have done
with the drywall to prevent this? By now, probably not much can be done
to fix it, since the corners open and close with the seasons to some
extent (it will be less noticeable when summer humidity and heat return).
I am going to clean out and fill the three corners with flexible white
caulk, but I expect there will still be some cracking, at least of the
paint layer.

drywall corners opening up
 

donald girod wrote:
By "exterior corner" I mean the corners of the exterior walls of the
house--these are, of course, interior (cove) corners of the drywall.
Anyway, lumber shrinks from moisture loss just twice as much radially
as it does tangentially, but of course almost not at all lengthwise
(it does expand and contract lengthwise to a measurable degree with
temperature changes). A 2x6 should shrink .1", 5.5" to 5.4" going
from 19% to 12% moisture content, and I suppose that is what is
causing the trouble. I intend to put acrylic caulk in the crack when
I paint.

In that case I would tend to believe they used green wet lumber.

--
Joseph Meehan

Dia duit