|
Fluorescent lamp switch
I have a fluourescent lamp that has a button that I have to hold down
for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. |
"User Example" wrote in message . .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? |
SQLit wrote:
"User Example" wrote in message . .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? No, it's not that easy. I think Joseph was correct about the switch type. The OP didn't say it, but likely that lamp has a second (usually black) button you push to turn it off. The first (usually red) button closed a toggling switch to apply power to the lamp, but when held down a second momentary contact closed the filament circuit just like a "starter" did. After a couple of seconds the filaments were hot and when you released the button an inductive spike from the ballast started the flourescent's arc. Pushing the second button toggled the switch off. Sometimes there was no second button 'cause the first button had an "alternate on-off" switch action in addition to the momentary contact. If the OP really loves that old lamp he could replace the "broke" switch with a slide or toggle on-off switch plus a NO momentary closed pushbutton switch. It'd take two separate actions to light the lamp, but only one to shut it off. That's providing the OP knows what to look for and can trace out the wiring so he can figure out how to connect the two switches properly. That's probably what I'd do if that old lamp held memories for me and I was going to be the only person using it. :-) Jeff -- Jeffry Wisnia (W1BSV + Brass Rat '57 EE) "Truth exists; only falsehood has to be invented." |
"User Example" wrote in message
. .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? No, it's not that easy. I think Joseph was correct about the switch type. The OP didn't say it, but likely that lamp has a second (usually black) button you push to turn it off. The first (usually red) button closed a toggling switch to apply power to the lamp, but when held down a second momentary contact closed the filament circuit just like a "starter" did. After a couple of seconds the filaments were hot and when you released the button an inductive spike from the ballast started the flourescent's arc. Pushing the second button toggled the switch off. Sometimes there was no second button 'cause the first button had an "alternate on-off" switch action in addition to the momentary contact. If the OP really loves that old lamp he could replace the "broke" switch with a slide or toggle on-off switch plus a NO momentary closed pushbutton switch. It'd take two separate actions to light the lamp, but only one to shut it off. That's providing the OP knows what to look for and can trace out the wiring so he can figure out how to connect the two switches properly. That's probably what I'd do if that old lamp held memories for me and I was going to be the only person using it. :-) It is actually one of those magnifying glass lamps like on workbench tables. It's a nice one so I want to fix the lamp if I can. I took the broken switch apart to see what is wrong and how it works. The button had a piece broken off and it is missing so I can't fix it. The switch similar to described above. There are two parts actually. One part turns on or off each time the button is pressed via a ratcheting spinner. The 2nd part turns on only momentarily when the switch is pressed. I have seen 3 position toggle switches with the 3rd position spring loaded. If I could find one of those I could make it work. I tried looking in digi-key but didnt see one, though. |
"User Example" wrote in message It is actually one of those magnifying glass lamps like on workbench tables. It's a nice one so I want to fix the lamp if I can. I took the broken switch apart to see what is wrong and how it works. The button had a piece broken off and it is missing so I can't fix it. It may be worth buying a cheap fixture for undercounter lighting and taking the switch out. They sell for less than $10. |
User Example wrote:
"User Example" wrote in message . .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? No, it's not that easy. I think Joseph was correct about the switch type. The OP didn't say it, but likely that lamp has a second (usually black) button you push to turn it off. The first (usually red) button closed a toggling switch to apply power to the lamp, but when held down a second momentary contact closed the filament circuit just like a "starter" did. After a couple of seconds the filaments were hot and when you released the button an inductive spike from the ballast started the flourescent's arc. Pushing the second button toggled the switch off. Sometimes there was no second button 'cause the first button had an "alternate on-off" switch action in addition to the momentary contact. If the OP really loves that old lamp he could replace the "broke" switch with a slide or toggle on-off switch plus a NO momentary closed pushbutton switch. It'd take two separate actions to light the lamp, but only one to shut it off. That's providing the OP knows what to look for and can trace out the wiring so he can figure out how to connect the two switches properly. That's probably what I'd do if that old lamp held memories for me and I was going to be the only person using it. :-) It is actually one of those magnifying glass lamps like on workbench tables. It's a nice one so I want to fix the lamp if I can. I took the broken switch apart to see what is wrong and how it works. The button had a piece broken off and it is missing so I can't fix it. The switch similar to described above. There are two parts actually. One part turns on or off each time the button is pressed via a ratcheting spinner. The 2nd part turns on only momentarily when the switch is pressed. I have seen 3 position toggle switches with the 3rd position spring loaded. If I could find one of those I could make it work. I tried looking in digi-key but didnt see one, though. Yes, but the ones like that I've seen are all "center off" types which make a momentary contact in one direction away from center and will toggle and stay in the opposite direction. That won't do it for you, you need to connect power to the lamp and then "play starter" by making and breaking the filament circuit. How about replacing the present switch with one of the commonly available "twist" lamp switches and drill another hole to mount a NO momenttary contact push button switch to start the lamp with? STOP THE PRESSES! Can you fit this one in? http://www.egaynor.com/edwin_gaynor_lampholders/666.htm It has the switching characteristics you need, and is the "two button" style I was bloviating about in my previous post. You'd need the "one lamp" model. HTH, Jeff -- Jeffry Wisnia (W1BSV + Brass Rat '57 EE) "Truth exists; only falsehood has to be invented." |
Edwin Pawlowski wrote:
"User Example" wrote in message It is actually one of those magnifying glass lamps like on workbench tables. It's a nice one so I want to fix the lamp if I can. I took the broken switch apart to see what is wrong and how it works. The button had a piece broken off and it is missing so I can't fix it. It may be worth buying a cheap fixture for undercounter lighting and taking the switch out. They sell for less than $10. Ah, but I betcha those will use a regular on-off switch and a cheapo glass bulb bimetal neon starter and paralleled capacitor (without a can) wired right in. I fixed GE undercounter light two weeks ago and it used one of those wired in starters. (Problem was just a thermal fuse glued to the ballast which had died of old age. wouldja believe I had a perfect match replacement thermal fuse in my "hell box"? Come to think of it, if he could fit in one of those wire-in starters he could solve his problem with a simple on-off switch. Yeah, he could take the starter out of the $10 light, along with the switch, couldn't he. Have we overkilled this one yet? Jeff -- Jeffry Wisnia (W1BSV + Brass Rat '57 EE) "Truth exists; only falsehood has to be invented." |
In article , Jeff Wisnia wrote:
SQLit wrote: "User Example" wrote in message . .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? No, it's not that easy. I think Joseph was correct about the switch type. The OP didn't say it, but likely that lamp has a second (usually black) button you push to turn it off. The first (usually red) button closed a toggling switch to apply power to the lamp, but when held down a second momentary contact closed the filament circuit just like a "starter" did. After a couple of seconds the filaments were hot and when you released the button an inductive spike from the ballast started the flourescent's arc. Pushing the second button toggled the switch off. Sometimes there was no second button 'cause the first button had an "alternate on-off" switch action in addition to the momentary contact. If the OP really loves that old lamp he could replace the "broke" switch with a slide or toggle on-off switch plus a NO momentary closed pushbutton switch. It'd take two separate actions to light the lamp, but only one to shut it off. That's providing the OP knows what to look for and can trace out the wiring so he can figure out how to connect the two switches properly. That's probably what I'd do if that old lamp held memories for me and I was going to be the only person using it. :-) Jeffry Wisnia I am familiar with this setup. The red pushbutton is a NO type that you push to get current to flow through the filaments of the fluorescent bulb, and in the next more modern step of fixture design is replaced by a starter. The black pushbutton is a NC type, and is replaced by a more usual on/off switch once the red pushbutton is replaced by a starter. If you want to replace pushbuttons with pushbuttons, it's not easy. You need pushbuttons rated for 125V and at least .35 amp, and also with some extra ability to handle inductive loads - maybe having a horsepower rating for motors that draw similar voltage and current - GOOD LUCK!!! I think you are better off, should you have any sentimental or emotional attachment to this fixture, to hack it into one with a starter and an on-off switch. This typically requires trashpicking or buying another fixture that has a starter, which is the easiest way in the USA to get a starter socket. Then, remove or disconnect the original pushbuttons and hack in an on-off switch and the starter socket. Now for wiring diagrams of basic / historic fluorescent fixtures: This is in Sam Goldwasser's "Repairfaq" documents, and I have an adequately current one for this purpose on fluorescent lamps at: http://www.misty.com/~don/f-lamp.html - Don Klipstein ) |
Don Klipstein wrote:
In article , Jeff Wisnia wrote: SQLit wrote: "User Example" wrote in message om... I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? No, it's not that easy. I think Joseph was correct about the switch type. The OP didn't say it, but likely that lamp has a second (usually black) button you push to turn it off. The first (usually red) button closed a toggling switch to apply power to the lamp, but when held down a second momentary contact closed the filament circuit just like a "starter" did. After a couple of seconds the filaments were hot and when you released the button an inductive spike from the ballast started the flourescent's arc. Pushing the second button toggled the switch off. Sometimes there was no second button 'cause the first button had an "alternate on-off" switch action in addition to the momentary contact. If the OP really loves that old lamp he could replace the "broke" switch with a slide or toggle on-off switch plus a NO momentary closed pushbutton switch. It'd take two separate actions to light the lamp, but only one to shut it off. That's providing the OP knows what to look for and can trace out the wiring so he can figure out how to connect the two switches properly. That's probably what I'd do if that old lamp held memories for me and I was going to be the only person using it. :-) Jeffry Wisnia I am familiar with this setup. The red pushbutton is a NO type that you push to get current to flow through the filaments of the fluorescent bulb, and in the next more modern step of fixture design is replaced by a starter. The black pushbutton is a NC type, and is replaced by a more usual on/off switch once the red pushbutton is replaced by a starter. If you want to replace pushbuttons with pushbuttons, it's not easy. You need pushbuttons rated for 125V and at least .35 amp, and also with some extra ability to handle inductive loads - maybe having a horsepower rating for motors that draw similar voltage and current - GOOD LUCK!!! I think you are better off, should you have any sentimental or emotional attachment to this fixture, to hack it into one with a starter and an on-off switch. This typically requires trashpicking or buying another fixture that has a starter, which is the easiest way in the USA to get a starter socket. Then, remove or disconnect the original pushbuttons and hack in an on-off switch and the starter socket. Now for wiring diagrams of basic / historic fluorescent fixtures: This is in Sam Goldwasser's "Repairfaq" documents, and I have an adequately current one for this purpose on fluorescent lamps at: http://www.misty.com/~don/f-lamp.html - Don Klipstein ) Thanks everyone for the ideas. They are all good. I am not sure what I will do, though. There isn't any spare room in the lamp to add a starter and it would be hard to even add an extra switch in there. I'll have to do some ciphering and figure out what I want to do. The link you provided will be helpful. |
Check out Ace Hardware. They usually
have, behind the service counter, a box of frequently used switches. I was surprised at the unusual stuff available. User Example wrote: Don Klipstein wrote: In article , Jeff Wisnia wrote: SQLit wrote: "User Example" wrote in message . .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. It is probably a NO momentary closed switch. Any Radio Shack or electronics store would have one. Searched where? No, it's not that easy. I think Joseph was correct about the switch type. The OP didn't say it, but likely that lamp has a second (usually black) button you push to turn it off. The first (usually red) button closed a toggling switch to apply power to the lamp, but when held down a second momentary contact closed the filament circuit just like a "starter" did. After a couple of seconds the filaments were hot and when you released the button an inductive spike from the ballast started the flourescent's arc. Pushing the second button toggled the switch off. Sometimes there was no second button 'cause the first button had an "alternate on-off" switch action in addition to the momentary contact. If the OP really loves that old lamp he could replace the "broke" switch with a slide or toggle on-off switch plus a NO momentary closed pushbutton switch. It'd take two separate actions to light the lamp, but only one to shut it off. That's providing the OP knows what to look for and can trace out the wiring so he can figure out how to connect the two switches properly. That's probably what I'd do if that old lamp held memories for me and I was going to be the only person using it. :-) Jeffry Wisnia I am familiar with this setup. The red pushbutton is a NO type that you push to get current to flow through the filaments of the fluorescent bulb, and in the next more modern step of fixture design is replaced by a starter. The black pushbutton is a NC type, and is replaced by a more usual on/off switch once the red pushbutton is replaced by a starter. If you want to replace pushbuttons with pushbuttons, it's not easy. You need pushbuttons rated for 125V and at least .35 amp, and also with some extra ability to handle inductive loads - maybe having a horsepower rating for motors that draw similar voltage and current - GOOD LUCK!!! I think you are better off, should you have any sentimental or emotional attachment to this fixture, to hack it into one with a starter and an on-off switch. This typically requires trashpicking or buying another fixture that has a starter, which is the easiest way in the USA to get a starter socket. Then, remove or disconnect the original pushbuttons and hack in an on-off switch and the starter socket. Now for wiring diagrams of basic / historic fluorescent fixtures: This is in Sam Goldwasser's "Repairfaq" documents, and I have an adequately current one for this purpose on fluorescent lamps at: http://www.misty.com/~don/f-lamp.html - Don Klipstein ) Thanks everyone for the ideas. They are all good. I am not sure what I will do, though. There isn't any spare room in the lamp to add a starter and it would be hard to even add an extra switch in there. I'll have to do some ciphering and figure out what I want to do. The link you provided will be helpful. |
"User Example" wrote in message . .. I have a fluourescent lamp that has a button that I have to hold down for a few seconds for the light to turn on. The switch is broke. Anyone know where I could find such a specialty switch? I searched around but no luck. You could try the manufacturer, as some of those switches can be proprietary to the light, and hard to come by as aftermarket items. But don't be surprised if the new switch with shipping costs more than replacing the whole light. AMUN |
Fluorescent lamp switch
replying to User Example, Larry wrote:
user wrote: It is actually one of those magnifying glass lamps like on workbench tables. It's a nice one so I want to fix the lamp if I can. I took the broken switch apart to see what is wrong and how it works. The button had a piece broken off and it is missing so I can't fix it. The switch similar to described above. There are two parts actually. One part turns on or off each time the button is pressed via a ratcheting spinner. The 2nd part turns on only momentarily when the switch is pressed. I have seen 3 position toggle switches with the 3rd position spring loaded. If I could find one of those I could make it work. I tried looking in digi-key but didnt see one, though. Hi, I have the same kind of lamp with the same problem. It has a 22w circline round fluorescent bulb. I finally found a switch after having the lamp tore apart for a long time and now I can't remember how to wire it back up. My switch has 4 contacts, socket has 2 blk and 2 white wires and of course 1 white and 1 black feed. Do you have any idea where I can find a wiring diagram for this setup. Thanks, Larry -- |
Fluorescent lamp switch
On 12/31/2014 12:44 AM, Larry wrote:
replying to User Example, Larry wrote: user wrote: It is actually one of those magnifying glass lamps like on workbench tables. It's a nice one so I want to fix the lamp if I can. I took the broken switch apart to see what is wrong and how it works. The button had a piece broken off and it is missing so I can't fix it. The switch similar to described above. There are two parts actually. One part turns on or off each time the button is pressed via a ratcheting spinner. The 2nd part turns on only momentarily when the switch is pressed. I have seen 3 position toggle switches with the 3rd position spring loaded. If I could find one of those I could make it work. I tried looking in digi-key but didnt see one, though. Hi, I have the same kind of lamp with the same problem. It has a 22w circline round fluorescent bulb. I finally found a switch after having the lamp tore apart for a long time and now I can't remember how to wire it back up. My switch has 4 contacts, socket has 2 blk and 2 white wires and of course 1 white and 1 black feed. Do you have any idea where I can find a wiring diagram for this setup. Thanks, Larry Yes, I too have one of those magnifiers and hate that kind of switch. But you just reminded me, I have 3 electronic ballasts which could be used for this lamp ... no starting needed and the ballast, actually a switching high voltage power supply, ionizes the gasses without starting. I'll have to see if I can retrofit one into the magnifier. --- This email has been checked for viruses by Avast antivirus software. http://www.avast.com |
Fluorescent lamp switch
replying to Amun, Randy wrote:
spamblocker wrote: "User Example" wrote in message . .. You could try the manufacturer, as some of those switches can be proprietary to the light, and hard to come by as aftermarket items. But don't be surprised if the new switch with shipping costs more than replacing the whole light. AMUN I have this type switch in my drafting lamp w/ 2 -18" FL bulbs. The base clamps to the table and the light floats over the table. New it cost 120 dollars. Good used ones are 50 to 75 dollars. Does anybody know where I can just buy a switch? I'd put a starter in it and a regular switch in but I'm not sure of the wiring schematic. Seems like the switch would be a common thing, but I just searched for 2 hours on line. tthhhhhht Zero~ Thanks for listening to my cry like a baby.... Randy -- |
Fluorescent lamp switch
replying to Larry, gertab wrote:
Larry wrote: Hi, I have the same kind of lamp with the same problem. It has a 22w circline round fluorescent bulb. I finally found a switch after having the lamp tore apart for a long time and now I can't remember how to wire it back up. My switch has 4 contacts, socket has 2 blk and 2 white wires and of course 1 white and 1 black feed. Do you have any idea where I can find a wiring diagram for this setup. Thanks, Larry What is the brand and model of the replacement switch you purchased? I was hoping that Grainger would sell a replacement switch since their Lumapro 6MNU0 matches what I have. They told me today (9/15/15) that they don't sell the replacement switch. -- -- |
Fluorescent lamp switch
replying to Randy, Randy wrote:
Randy wrote: I have this type switch in my drafting lamp w/ 2 -18" FL bulbs. The base clamps to the table and the light floats over the table. New it cost 120 dollars. Good used ones are 50 to 75 dollars. Does anybody know where I can just buy a switch? I'd put a starter in it and a regular switch in but I'm not sure of the wiring schematic. Seems like the switch would be a common thing, but I just searched for 2 hours on line. tthhhhhht Zero~ Thanks for listening to my cry like a baby.... Randy Ok I think I found what I need here at Taber Luxo-Lighting.com https://www.luxo-lighting.com/SPD/lu...1265655326.jsp My light happens to be a Ledu and doesn't have that adaper on it. But 14 dollars isn't a bad price. I might try that. Comments? -- |
Fluorescent lamp switch
replying to User Example, Jacksf wrote:
I actually found a lamp with a similar two-button switch and old floresent workings. I'm upgrading it to an LED strip and want to keep the look of the red and black push buttons so replacing them with similar switches that still have red and black caps. Technically only the red will need to be pressed once for on and again for off, but will maintain the look vs replacing with rocker switch. -- for full context, visit http://www.homeownershub.com/mainten...tch-30957-.htm |
Fluorescent lamp switch
replying to Jeff Wisnia, Shorty wrote:
http://www.egaynor.com/edwin_gaynor_lampholders/666.htm Thanks Jeff I looked for hours to find one of these. Thank you 100 thank yous. This is for my Ledu drafting table light that I purchased in 1976. -- for full context, visit http://www.homeownershub.com/mainten...tch-30957-.htm |
Fluorescent lamp switch
replying to Jacksf, Shorty wrote:
http://www.egaynor.com/edwin_gaynor_lampholders/666.htm Where did you get the LED strip? -- for full context, visit http://www.homeownershub.com/mainten...tch-30957-.htm |
Fluorescent lamp switch
replying to SQLit, Matt wrote:
Well, Radio Shack is out of business, and a huge electronics store in my city claims not to carry these parts -- for full context, visit https://www.homeownershub.com/mainte...tch-30957-.htm |
Fluorescent lamp switch
replying to Jeff Wisnia, Matt wrote:
Jeff, dumb question as Im a beginner: these small desk lamps with the red/black button starter dont have a ballast....the only other part is a smal in-line transformer, thats it! So, the switch acts as a starter? Why is no ballast needed in these lamps like ceiling mounted fluorescent lights? -- for full context, visit https://www.homeownershub.com/mainte...tch-30957-.htm |
Fluorescent lamp switch
On Thu, 01 Nov 2018 03:14:03 GMT, Matt
m wrote: replying to Jeff Wisnia, Matt wrote: Jeff, dumb question as Im a beginner: these small desk lamps with the red/black button starter dont have a ballast....the only other part is a smal in-line transformer, thats it! So, the switch acts as a starter? Why is no ballast needed in these lamps like ceiling mounted fluorescent lights? That "transformer" IS the ballast. It is a "manual start ballast" |
Fluorescent lamp switch
replying to Jeff Wisnia, csnyder wrote:
I had one of those back in my highschool days - a red button and a black one - a branze/brown colored lamp. I've seen numerous ones at antique shops locally here in the Waterloo Ontario aria - in working condition - in the $15 range. I'm sur the switch would be worth that much if you could find one. -- for full context, visit https://www.homeownershub.com/mainte...tch-30957-.htm |
Fluorescent lamp switch
|
Fluorescent lamp switch
replying to Jeff Wisnia, Edward puro. wrote:
Can I make a suggestion. Wire a starter in place of the start switch. I did it for my lamp and it works just fine. I put in the base of the lamp, had the room and used small auto vacuum hose to hold the wire onto the starters terminals.so I can replace it when needed. ED, OUT. -- for full context, visit https://www.homeownershub.com/mainte...tch-30957-.htm |
| All times are GMT +1. The time now is 02:44 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2004 - 2014 DIYbanter