Malfunctioning Garage Door Opener on Warm Afternoons
I'm having trouble with my garage door opener. On warm afternoons when
the sun is shining on the garage door, it won't close properly. It goes down part way, then the light flashes and the door goes back up as if there's a blockage in front of the infrared beams. I've checked for something in the way, as well as the alignment of the beams. Early in the morning and at night, it works perfectly. What is the heat of the sun doing and how can I remedy it? By the way, it's a 1/2 h.p. Craftsman and a metal rollaway door. Thanks. -Fleemo |
In article .com,
wrote: I'm having trouble with my garage door opener. On warm afternoons when the sun is shining on the garage door, it won't close properly. It goes down part way, then the light flashes and the door goes back up as if there's a blockage in front of the infrared beams. I've checked for something in the way, as well as the alignment of the beams. Early in the morning and at night, it works perfectly. What is the heat of the sun doing and how can I remedy it? The heat of the sun is warping or otherwise expanding the door so the wheels are binding on the side tracks. See if you can spot where and bend the track a bit so it won't bind. -- Rich Greenberg Marietta, GA, USA richgr atsign panix.com + 1 770 321 6507 Eastern time. N6LRT I speak for myself & my dogs only. VM'er since CP-67 Canines:Val, Red & Shasta (RIP),Red, husky Owner:Chinook-L Atlanta Siberian Husky Rescue. www.panix.com/~richgr/ Asst Owner:Sibernet-L |
Thanks for the input, Rich.
Well, I went out and ran the garage door opener several times, trying to see if there was a place where the wheels were binding. After several tries, I heard a loud "snap" and a puff of smoke came out of the opener. Looks like I ran it one too many times. :( It still functions, but I smell smoke when I run it. Never a good sign. Drat and double drat. -Fleemo |
Don't give up so fast Flee. There's a lot of dust up there that could
have shaken loose and looked like smoke as the mechanism shuttered trying to open. The fit of the door is surely binding with the expansion caused by the heat of the sun. Look closely at the side rails and see if there's a way to loosen them slightly or reposition them . There are ways to fix it, but only after you find where it binds. Even if the width of the opening is too small and is pinching the door, that can be handled. |
wrote: Thanks for the input, Rich. Well, I went out and ran the garage door opener several times, trying to see if there was a place where the wheels were binding. After several tries, I heard a loud "snap" and a puff of smoke came out of the opener. Looks like I ran it one too many times. :( It still functions, but I smell smoke when I run it. Never a good sign. Drat and double drat. -Fleemo Sounds like the sun light is washing out the infrared beams. Try swapping the two photo-cells. One is a transmitter & one is a receiver, so this usually solves the problem. The smoke was probably from the capacitor. Once it cools down the opener may no longer work, motor will just buzz. Even if it keeps working the cap should be changed. Doordoc www.DoorsAndOpeners.com |
Thanks for the advice, here folks. I genuinely appreciate it.
Sounds like the sun light is washing out the infrared beams. Try swapping the two photo-cells. One is a transmitter & one is a receiver, so this usually solves the problem. Ya know, Doc, that might make sense. The door didn't appear to be binding to my untrained eye. And at this time of year, the sun does shine in on one of the sensors at certain times of the day. It just might be that. The smoke was probably from the capacitor. Once it cools down the opener may no longer work, motor will just buzz. Even if it keeps working the cap should be changed. You're right again, Doc. It was indeed smoke, and the unit did stop working at all once it cooled down. So is the capacitor a user-replaceable part? If so, where can they be purchased? At Sears? - Fleemo |
Sunlight wash-out is a very common problem here in sunny SW Florida.
Sears would have the capacitor if the people there know what they are doing. Around here if you don't have a Sears part number they usually can't help you. Any Liftmaster dealer should also have the part. You could probably also get the capacitor at any motor shop or Grainger, however while the rating may be the same the actual size (diameter) may be different & therefore may not fit in the original holder. The rating on yours should be printed on the side w/ something like 220 VAC, 53-64 MFD. It's ok to go up on the VAC rating, but the MFD should be as close as possible. Doordoc |
Thanks for the info, Doc.
The strangest thing... today my wife came home and absent-mindedly pushed the garage door remote control -- and it opened! I got home shortly thereafter and tried it myself, and sure enough. There was a faint smell of electrical smoke in the air. I'm sure the unit is on its last legs, but does the fact that it's operating again still sound like a capacitor problem? -Fleemo |
Yes. Pull the plug, take off the cover, & inspect the capacitor (gray
or black cylinder near motor w/ four wires) & usually it will be obvious that it is blown or there may also be an oily substance in the cover. Doordoc |
Thanks Doc. I'll do that when I get home from work tonight. I
appreciate your help. -F |
Doc, I do believe you just saved me somewhere between $150 and $300. I
spent $6 on a new capacitor and it seems to be working just fine now, so a sincere thank you for your advice. The weather has cooled dramatically and the clouds have hidden the sun, so I'll have to wait a few days to try your sensor switcharoo. -F |
Well, unfortunately I'm still having problems with my garage door not
going down on warm days. I've scrutinized the tracks, but there's no obvious point where the rollers bind. It goes up fine, it's only when I try and lower the door that the garage door opener unit flashes and the door reverses. I experimented with blocking the sunlight from the infrared beams without success, though I still haven't actually switched them out. But my tests made me think the problem lies elsewhere. Perhaps a good lubricating would do the trick? Should a special type of grease or oil be used on the tracks, or would WD-40 work just fine? -Fleemo |
How far does the door close? For some reason I was thinking it wouldn't
close at all. There is a special oil made for garage doors, but it really only needs to be put on the hinges & the rollers (if the rollers have ball bearings) but light weight motor oil or 3-in-1 oil also works. WD-40 is silicone based which gets sticky & the oil part evaporates very quickly so it's not the best thing to use. Definitely do not use grease on the rollers or door track. Grease will collect dust & dirt and may make the matter worse. If the door is closing part way & then reversing i would suspect the door sections are rubbing hard against the jambs or molding. Simple solution for that is to rub a candle along the entire inside edge of the jamb/molding that the door touches as it closes. If you move the molding the door won't seal when it's closed & if you try to plane it down it will look like crap from outside once the door is closed. Simply wax it once or twice a year & it should work fine. Doordoc |
Hey Doc,
The door tends to close about three feet or so before it reverses back and the lights flash, and as I've mentioned, only when it's warm outside. I am able to push and hold the doorbell-like button down the duration of the closure to make it go down, but for some reason this doesn't work using the remote controls. (FYI, it's a metal door.) I'll go out and pick up some 3-in-1 oil and do the hinges and rollers. I'll also investigate the jambs and try a little candle wax as you suggested. Thanks much for the suggestions. -Fleemo |
|
|
Well, I think it might be time to call in the pros. I went out and got
some 3-in-1 oil and oiled every moving part in sight. I then applied candle wax to the door jamb. The door did appear to get pretty close to the jamb in some places, but I wouldn't know how to adjust that. During my testing, I blew out the capitor again. Ugh. In any case, I do appreciate all the input offered here, I truly do. -Fleemo |
All times are GMT +1. The time now is 02:46 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter