Dead plasma globe - need new power supply
 

My plasma globe (actually it's a tall red spiral, but same idea) died. It runs for about 2 minutes, then suddenly goes off. The AC wall wart is tested as ok, the DC convertor is tested as ok. But the part that makes the high voltage from the 15V DC is sealed in that wax stuff (for heat dissipation?) so I can't possibly repair it. Where can I get a replacement supply? Or is it easy enough to make one using parts that would cost less than just buying a new globe?

--
Confucius say: "Foolish man give wife grand piano. Wise man give wife upright organ."

Dead plasma globe - need new power supply
 

On 20/04/14 04:33, Uncle Peter wrote:
My plasma globe (actually it's a tall red spiral, but same idea) died.
It runs for about 2 minutes, then suddenly goes off. The AC wall wart
is tested as ok, the DC convertor is tested as ok. But the part that
makes the high voltage from the 15V DC is sealed in that wax stuff (for
heat dissipation?) so I can't possibly repair it. Where can I get a
replacement supply? Or is it easy enough to make one using parts that
would cost less than just buying a new globe?

Have you checked the return path ??

Dead plasma globe - need new power supply
 

On Sun, 20 Apr 2014 01:03:37 +0100, Rheilly Phoull wrote:

On 20/04/14 04:33, Uncle Peter wrote:
My plasma globe (actually it's a tall red spiral, but same idea) died.
It runs for about 2 minutes, then suddenly goes off. The AC wall wart
is tested as ok, the DC convertor is tested as ok. But the part that
makes the high voltage from the 15V DC is sealed in that wax stuff (for
heat dissipation?) so I can't possibly repair it. Where can I get a
replacement supply? Or is it easy enough to make one using parts that
would cost less than just buying a new globe?

Have you checked the return path ??

I would if I knew where it was.

--
What's a birth control pill?
The OTHER thing a woman can put in her mouth to keep from becoming pregnant.

Dead plasma globe - need new power supply
 

On 21/04/14 03:05, Uncle Peter wrote:
On Sun, 20 Apr 2014 01:03:37 +0100, Rheilly Phoull
wrote:

On 20/04/14 04:33, Uncle Peter wrote:
My plasma globe (actually it's a tall red spiral, but same idea) died.
It runs for about 2 minutes, then suddenly goes off. The AC wall wart
is tested as ok, the DC convertor is tested as ok. But the part that
makes the high voltage from the 15V DC is sealed in that wax stuff (for
heat dissipation?) so I can't possibly repair it. Where can I get a
replacement supply? Or is it easy enough to make one using parts that
would cost less than just buying a new globe?

Have you checked the return path ??

I would if I knew where it was.

So can you melt out the "wax" and take a decko at the "works" ??

Dead plasma globe - need new power supply
 

On Wed, 23 Apr 2014 10:33:38 +0100, Rheilly Phoull wrote:

On 21/04/14 03:05, Uncle Peter wrote:
On Sun, 20 Apr 2014 01:03:37 +0100, Rheilly Phoull
wrote:

On 20/04/14 04:33, Uncle Peter wrote:
My plasma globe (actually it's a tall red spiral, but same idea) died.
It runs for about 2 minutes, then suddenly goes off. The AC wall wart
is tested as ok, the DC convertor is tested as ok. But the part that
makes the high voltage from the 15V DC is sealed in that wax stuff (for
heat dissipation?) so I can't possibly repair it. Where can I get a
replacement supply? Or is it easy enough to make one using parts that
would cost less than just buying a new globe?

Have you checked the return path ??

I would if I knew where it was.

So can you melt out the "wax" and take a decko at the "works" ??

I'm sorry, I only speak English.

--
"Have you read The Three Musketeers?"
"No, only one of them."

Dead plasma globe - need new power supply
 

"Uncle Peter" wrote in message
...
On Wed, 23 Apr 2014 10:33:38 +0100, Rheilly Phoull
wrote:

On 21/04/14 03:05, Uncle Peter wrote:
On Sun, 20 Apr 2014 01:03:37 +0100, Rheilly Phoull
wrote:

On 20/04/14 04:33, Uncle Peter wrote:
My plasma globe (actually it's a tall red spiral, but same idea) died.
It runs for about 2 minutes, then suddenly goes off. The AC wall wart
is tested as ok, the DC convertor is tested as ok. But the part that
makes the high voltage from the 15V DC is sealed in that wax stuff
(for
heat dissipation?) so I can't possibly repair it. Where can I get a
replacement supply? Or is it easy enough to make one using parts that
would cost less than just buying a new globe?

Have you checked the return path ??

I would if I knew where it was.

So can you melt out the "wax" and take a decko at the "works" ??

I'm sorry, I only speak English.

Being cunnilingual has its advantages.

Dead plasma globe - need new power supply
 

On Sat, 10 May 2014 22:11:57 +0100, Ian Field wrote:



"Uncle Peter" wrote in message
...
On Wed, 23 Apr 2014 10:33:38 +0100, Rheilly Phoull
wrote:

On 21/04/14 03:05, Uncle Peter wrote:
On Sun, 20 Apr 2014 01:03:37 +0100, Rheilly Phoull
wrote:

On 20/04/14 04:33, Uncle Peter wrote:

Have you checked the return path ??

I would if I knew where it was.

So can you melt out the "wax" and take a decko at the "works" ??

I'm sorry, I only speak English.

Being cunnilingual has its advantages.

Confucius say man who speak with forked tongue satisfy two women at once.

--
What do you call kinky sex with chocolate?
S&M&M