LCD projector
 

"Chuck Chandler" wrote in message
...
Powering up w/out bulb:
Yes. Look for the circuit board that has two heavily insulated wires (has
25KV on them) going to bulb. There is proabably 2-3 signal wires nearby.
Something can usually be done to provide a signal, the signal basically is
on/off low voltage, and the signal just tells the rest of the projector
that
the bulb powered up ok.
I've used an alternate projector bulb on my TV for the last 100 hours or
so,
works fine. Original cost about $300, I got the cheapest UHP off of eBay
for
$23 delivered and adapted it. Original was 100 watts, 3" diameter,
replacement was 120/132 watts, 1.5" diameter. CPU fan provides additional
cooling.
The light from both bulbs gets focused very effeciently down to 1/8"
diameter spot from the reflector shape. Your replacement bulb will have to
do likewise.
There is a really good chance of electrocuting yourself or blowing up your
circuitry trying to do the same thing I did. The halide bulbs can explode
quite well; safety glasses/shield and high collar jacket are minimal
safety
standards. I alpha tested mine on New Year's eve on my front porch.


What are you using to ballast the new bulb? I'd be very hesitant to go up in
wattage, in that unlikely scenario that it catches fire, you're pretty well
screwed.

What are you using to ballast the new bulb? I'd be very hesitant to go up
in
wattage, in that unlikely scenario that it catches fire, you're pretty
well
screwed.

I'm not sure what you mean, but both are video projector bulbs- they use
25KV to start an arc, then about 20-50 volts to maintain the arc. So of
course I am using the original ballast (100 watt) with the slightly higher
(120 watt) bulb. The ballast is specifically designed to limit current, or
you could say regulate current, so I am pretty sure it is only putting out
100 watts, although it might be generating a slightly different voltage to
do so, which is really a function of the electrode gap. Thus it might be
getting a little hotter, hence the extra fans. This LCD projection tv had
30,000 hours on it when I got it for $1.25, but it really does look great. I
have no worry about it catching fire, but there could be a component failure
in it's future.

On the other hand, putting a lower watt bulb than the ballast is designed to
use will result in a very hot bulb explosion rather quickly, as the ballast
IS going to put out the same wattage regardless of which bulb is in place.

Normally, the problem of switching bulbs is that the ballast will not start
the arc at all. But I got lucky and it starts on the first attempt every
time.

"Chuck Chandler" wrote in message
...


What are you using to ballast the new bulb? I'd be very hesitant to go
up
in
wattage, in that unlikely scenario that it catches fire, you're pretty
well
screwed.

I'm not sure what you mean, but both are video projector bulbs- they use
25KV to start an arc, then about 20-50 volts to maintain the arc. So of
course I am using the original ballast (100 watt) with the slightly higher
(120 watt) bulb. The ballast is specifically designed to limit current, or
you could say regulate current, so I am pretty sure it is only putting out
100 watts, although it might be generating a slightly different voltage to
do so, which is really a function of the electrode gap. Thus it might be
getting a little hotter, hence the extra fans. This LCD projection tv had
30,000 hours on it when I got it for $1.25, but it really does look great.
I
have no worry about it catching fire, but there could be a component
failure
in it's future.

Ah, I thought you were using something else as the post was originally about
tricking the projector into thinking the lamp had started.

Using a lower wattage lamp is safe, though often you'll get a nasty color
shift if you operate a metal halide out of spec but that depends on the
design of the lamp. Also, surprising as it may be, operating them under
wattage will usually drastically decrease lamp life because the electrodes
run too cool and sputter heavily as the arc restrikes between the
half-cycles. YMMV though, for what you have invested in it it's a worthwhile
experiment.