Sam Goldwasser wrote:
I need to fab 50-100 small (1"x1"), double sided, plated through hole
PCBs. No special requirements. Soldermask desireable but not essential.
Cost is of course the issue. What I've found so far is around $300 for
a full feature service including separating the boards. I've done this
before without soldermask and uncut for something like $100-150 and might
do that again but would rather not have to use the bandsaw and files. :)

Thanks.

--- sam | Sci.Electronics.Repair FAQ Mirror: http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is ignored.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.

Try http://barebonespcb.com

Darrell Harmon

PCB fab recommendations for moderate run of small boards
 

I need to fab 50-100 small (1"x1"), double sided, plated through hole
PCBs. No special requirements. Soldermask desireable but not essential.
Cost is of course the issue. What I've found so far is around $300 for
a full feature service including separating the boards. I've done this
before without soldermask and uncut for something like $100-150 and might
do that again but would rather not have to use the bandsaw and files. :)

Thanks.

--- sam | Sci.Electronics.Repair FAQ Mirror: http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is ignored.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.

On 10 Nov 2004 08:47:57 -0500, Sam Goldwasser wrote:

I need to fab 50-100 small (1"x1"), double sided, plated through hole
PCBs. No special requirements. Soldermask desireable but not essential.
Cost is of course the issue. What I've found so far is around $300 for
a full feature service including separating the boards. I've done this
before without soldermask and uncut for something like $100-150 and might
do that again but would rather not have to use the bandsaw and files. :)

I've used http://www.custompcb.com for jobs like this.

"Sam Goldwasser" wrote in message
...
I need to fab 50-100 small (1"x1"), double sided, plated through hole
PCBs. No special requirements. Soldermask desireable but not essential.
Cost is of course the issue. What I've found so far is around $300 for
a full feature service including separating the boards. I've done this
before without soldermask and uncut for something like $100-150 and might
do that again but would rather not have to use the bandsaw and files. :)

Thanks.

--- sam | Sci.Electronics.Repair FAQ Mirror:
http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the
excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is
ignored.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.

Hi Sam,

We have a supplier in Taiwan that will do small runs, including populating
components. Contact me on the e-mail address spamtrap at hayclan-oz dot com.

Regards
Wes.

budgie writes:

On 10 Nov 2004 08:47:57 -0500, Sam Goldwasser wrote:

I need to fab 50-100 small (1"x1"), double sided, plated through hole
PCBs. No special requirements. Soldermask desireable but not essential.
Cost is of course the issue. What I've found so far is around $300 for
a full feature service including separating the boards. I've done this
before without soldermask and uncut for something like $100-150 and might
do that again but would rather not have to use the bandsaw and files. :)

I've used http://www.custompcb.com for jobs like this.

Thanks. I just did it with them and was fine. They were very responsive
to questions and the quality seems decent. I wouldn't say it's super but
certainly adequate if you're not doing super fine pitch PCBs.

--- sam | Sci.Electronics.Repair FAQ Mirror: http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is ignored.
To contact me, please use the Feedback Form in the FAQs.