Hi guys. Got a question for you all. CTC195A projection set. Came in, shuts
down instantly. Checked various things in horizontal, decided bad flyback.
Got an original RCA flyback, didn't come with any cap, resistor like I've
seen mentioned in another post. Just a HV wire if needed. Anyway, I put in.
Set runs like a champ, perfect picture and so forth, for 2 days. Put back
in. Lady calls back a day or so later. Flyback has burned a hole in the
side, and is arcing to metal heat sink nearby, about half an inch away.

Anyone seen this before? I'd rather try to figure out why it did that before
ruining another one. I have a HV splitter standing by in case that may have
an effect.

Thanks very much,

Danny

Did the first fly have hole in it too. If not probably just a bad
fly...Haven't been there myself...knock on wood...but I've read other
guys complaining about similar situations ever since china took over
RCA. Might wanna check B+ is normal.

wrote in message ...
Hi guys. Got a question for you all. CTC195A projection set. Came in, shuts
down instantly. Checked various things in horizontal, decided bad flyback.
Got an original RCA flyback, didn't come with any cap, resistor like I've
seen mentioned in another post. Just a HV wire if needed. Anyway, I put in.
Set runs like a champ, perfect picture and so forth, for 2 days. Put back
in. Lady calls back a day or so later. Flyback has burned a hole in the
side, and is arcing to metal heat sink nearby, about half an inch away.

Anyone seen this before? I'd rather try to figure out why it did that before
ruining another one. I have a HV splitter standing by in case that may have
an effect.

Thanks very much,

Danny

Did the original bad fly have a hole in it too? If not probably just
a bad fly. Hasn't happened to me (knock on wood)...read other guys
complaining of similar new fly failures since china took over RCA.
Might want to check for Normal B+ not to high

On Sun, 24 Oct 2004 01:12:06 -0500, wrote:

Hi guys. Got a question for you all. CTC195A projection set. Came in, shuts
down instantly. Checked various things in horizontal, decided bad flyback.
Got an original RCA flyback, didn't come with any cap, resistor like I've
seen mentioned in another post. Just a HV wire if needed. Anyway, I put in.
Set runs like a champ, perfect picture and so forth, for 2 days. Put back
in. Lady calls back a day or so later. Flyback has burned a hole in the
side, and is arcing to metal heat sink nearby, about half an inch away.

Anyone seen this before? I'd rather try to figure out why it did that before
ruining another one. I have a HV splitter standing by in case that may have
an effect.

Thanks very much,

Danny


The replacement flyback was possibly faulty.

Tom

wrote in message
...
Hi guys. Got a question for you all. CTC195A projection set. Came in,
shuts
down instantly. Checked various things in horizontal, decided bad flyback.
Got an original RCA flyback, didn't come with any cap, resistor like I've
seen mentioned in another post. Just a HV wire if needed. Anyway, I put
in.
Set runs like a champ, perfect picture and so forth, for 2 days. Put back
in. Lady calls back a day or so later. Flyback has burned a hole in the
side, and is arcing to metal heat sink nearby, about half an inch away.

Anyone seen this before? I'd rather try to figure out why it did that
before
ruining another one. I have a HV splitter standing by in case that may
have
an effect.

Thanks very much,

Danny



Did you measure the HV? If it wasn't excessive I would suspect the
replacement was defective.

Did you use the RCA 239111 or Generic.
I have replaced dozens of these and never had a bad one Yet !

kip

It was an original RCA 239111 from local RCA auth parts house. It and the
one that came in DOA (worked as well as the original) both had build dates
of mid August 2004. Perhaps a flaky batch. I have put my name in for one
from next litter. Just kinda makes me scratch my head.

Danny

I can't think of anything that would burn a hole in a flyback other than poor
construction; excessive H.V. would cause shutdown; or at least an arc somewhere
else, particularly around the anode caps or splitter...