Screwdriver bits
 

I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?

--

Screwdriver bits
 

Where did you get the poor things?

The cheap box of bits I got from Horrible Freight, I'd be rather more
concerned that they're going to snap into pieces if I force them hard.

I've bent and twisted dozens of screwdrivers, though.

Tim

--
Seven Transistor Labs, LLC
Electrical Engineering Consultation and Contract Design
Website: https://www.seventransistorlabs.com/

"Tom Del Rosso" wrote in
message ...
I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a flat
screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a single-piece
screwdriver. Does anybody make harder bits?

--

Screwdriver bits
 

On Fri, 23 Feb 2018 22:42:47 -0500, "Tom Del Rosso"
wrote:

I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?

Put some Viagra tablets in the container where you keep your bits. They
will get hard! :)

Screwdriver bits
 

Tom Del Rosso wrote:
I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?

Snap-On and Proto both make good torx bits. $12 per bit.
They don't bend, they just suddenly break.

Screwdriver bits
 

Tom Del Rosso wrote:
I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?

Proto and Mac do, I think PB Baumann does also. They aren't cheap, but
they work. We use the Proto ones.

In addition you may want to invest in some Kroil or PB Blaster, and
maybe a small torch....
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

Screwdriver bits
 

Don't forget they have a lifetime warranty on hand tools so get a better
replacement.


Tim Williams wrote:
Where did you get the poor things?

The cheap box of bits I got from Horrible Freight, I'd be rather more
concerned that they're going to snap into pieces if I force them hard.

I've bent and twisted dozens of screwdrivers, though.

Tim

Screwdriver bits
 

On Fri, 23 Feb 2018 22:42:47 -0500, "Tom Del Rosso"
wrote:

I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?

Try Milwaukee bits. There are a number of others that are designed
for impact drivers but Milwaukee are the best, IMO.

Screwdriver bits
 

On 2018/02/23 7:42 PM, Tom Del Rosso wrote:
I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?


Get good quality bits and your problem goes away. If you buy off Amazon
or eBay then you get 3rd world quality, not 1st world.

Try some Hazet tools some time as an example of 1st world quality. Be
sure you get them from a factory authorized distributor or you are
likely to just buy counterfeit.

https://www.hazet.de/produktkatalog/...hp?language=en

There is a reason why some brands of tools cost more than others...

John :-#)#

--
(Please post followups or tech inquiries to the USENET newsgroup)
John's Jukes Ltd.
MOVED to #7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3
(604)872-5757 (Pinballs, Jukes, Video Games)
www.flippers.com
"Old pinballers never die, they just flip out."

Screwdriver bits
 

On 24/02/2018 15:12, John Robertson wrote:
On 2018/02/23 7:42 PM, Tom Del Rosso wrote:
I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver.Â* The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver.Â* Does anybody make harder bits?


Get good quality bits and your problem goes away. If you buy off Amazon
or eBay then you get 3rd world quality, not 1st world.

Try some Hazet tools some time as an example of 1st world quality. Be
sure you get them from a factory authorized distributor or you are
likely to just buy counterfeit.

https://www.hazet.de/produktkatalog/...hp?language=en

There is a reason why some brands of tools cost more than others...

Extra cost of marketing??

Lots of profits for brand owners?


--
Mike Perkins
Video Solutions Ltd
www.videosolutions.ltd.uk

Screwdriver bits
 

On Sat, 24 Feb 2018 15:24:25 +0000, Mike Perkins
wrote:

On 24/02/2018 15:12, John Robertson wrote:
On 2018/02/23 7:42 PM, Tom Del Rosso wrote:
I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver.* The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver.* Does anybody make harder bits?


Get good quality bits and your problem goes away. If you buy off Amazon
or eBay then you get 3rd world quality, not 1st world.

Try some Hazet tools some time as an example of 1st world quality. Be
sure you get them from a factory authorized distributor or you are
likely to just buy counterfeit.

https://www.hazet.de/produktkatalog/...hp?language=en

There is a reason why some brands of tools cost more than others...

Extra cost of marketing??

Lots of profits for brand owners?

Better quality.

Something that actually does what it promises?

Screwdriver bits
 

Mike Perkins wrote:
On 24/02/2018 15:12, John Robertson wrote:

Try some Hazet tools some time as an example of 1st world quality. Be
sure you get them from a factory authorized distributor or you are
likely to just buy counterfeit.

https://www.hazet.de/produktkatalog/...hp?language=en

There is a reason why some brands of tools cost more than others...

Extra cost of marketing??

Ever seen ads for Hazet, PB, or Proto? Those guys don't advertise
much, because they don't really need to.

The people who put money into marketing are the mid-grade outfits like
Snap-On and Mac, who make respectable but not marvelous tools and
make up for that in advertising.

Lots of profits for brand owners?

Maybe, but I suspect there's a lot more money selling millions of crappy
tools than hundreds of really nice ones. Harbor Freight is making money
hand over fist, and so are their suppliers. There's not a lot of money
in selling $100 Swiss pattern files, because there are only a limited number
of people who are going to buy them. Vaillorbe makes great tools, and they
might have high margins too, but they aren't making huge profits.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

Screwdriver bits
 

In article , says...
Maybe, but I suspect there's a lot more money selling millions of crappy
tools than hundreds of really nice ones. Harbor Freight is making money
hand over fist, and so are their suppliers. There's not a lot of money
in selling $100 Swiss pattern files, because there are only a limited number
of people who are going to buy them. Vaillorbe makes great tools, and they
might have high margins too, but they aren't making huge profits.




Like a man that started a food chain of stores in the town I live in.
He sold brand name food, same as any other store. Then one day we
marked everythign down. I was a stock boy then around 17 years old. His
idea was to make 10 fast pennies instead of one slow dime. He would by
a boxcar load of an item and put it in his warehouse.
A number of years later the three big names like A&P, Kroger and Winn
Dixie closed and moved out of town. Now there are several of his stores
around in the near by are, and the only other food places are one of
each, Walmart, Audies, and one other store.

Many of the Harbor Freight tools are good enough for a one or two time
use. I have some, but would not buy them if I was using them to make a
living.Most of my better tools are the Craftsman tools from years ago.
The latter ones have not been as good of quality.

Screwdriver bits
 

On 2/24/18 4:53 PM, Ralph Mowery wrote:
Most of my better tools are the Craftsman tools from years ago.
The latter ones have not been as good of quality.

Round 1999-2000 Sears decided to ditch their OEM provider of
Craftsman tools in favor of a cheaper supplier.
They also introduced a new line of "Sears tools" that had mo\lifetime
warranty.

Oh, and the original OEM? They now sell tools with a lifetime warranty
through Home Depot. Their name? Husky.

And for the first six months, they also offered to honor the warranty on
any Craftsman tools.


--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

Screwdriver bits
 

Once upon a time on usenet wrote:
On Fri, 23 Feb 2018 22:42:47 -0500, "Tom Del Rosso"
wrote:

I just twisted a torx bit into a spiral trying to remove a rusted
screw, then used a Dremel to cut a slot across the top and took it
out with a flat screwdriver. The screwdriver didn't bend at all.

None of the bits I ever saw are made of hardened steel like a
single-piece screwdriver. Does anybody make harder bits?

Put some Viagra tablets in the container where you keep your bits.
They will get hard! :)

The voice of experience....
--
Shaun.

"Humans will have advanced a long, long way when religious belief has a cozy
little classification in the DSM*."
David Melville (in r.a.s.f1)
(*Diagnostic and Statistical Manual of Mental Disorders)

Screwdriver bits
 

On Fri, 23 Feb 2018 22:42:47 -0500, Tom Del Rosso wrote:

I just twisted a torx bit into a spiral trying to remove a rusted screw,
then used a Dremel to cut a slot across the top and took it out with a
flat screwdriver. The screwdriver didn't bend at all.

+1 I had the exact same experience here too; supposedly a premium brand
tool in this country 'n' all.
Mind you, to be fair, I also had a Snap-On [TM] straight screwdriver bit
snap off first time I used it (back in '78) maybe they've improved since.


--
This message may be freely reproduced without limit or charge only via
the Usenet protocol. Reproduction in whole or part through other
protocols, whether for profit or not, is conditional upon a charge of
GBP10.00 per reproduction. Publication in this manner via non-Usenet
protocols constitutes acceptance of this condition.