Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
STR-W6000S power IC
l am working on a refrigerator board which uses STR-W6000S power ic The resistor to pin 3 of the ic is burnt beyond recognition. l tried to find out from the manufacturers data sheet but all the application circuits there have no value marked on the resistors. can anyone give a typical value or how to figure out this value?
|
#2
Posted to sci.electronics.repair
|
|||
|
|||
STR-W6000S power IC
wrote:
l am working on a refrigerator board which uses STR-W6000S power ic The resistor to pin 3 of the ic is burnt beyond recognition. l tried to find out from the manufacturers data sheet but all the application circuits there have no value marked on the resistors. can anyone give a typical value or how to figure out this value? ** The data sheet gives a typical value of 0.27 ohms @ 1 watt - in the table under fig 22. If it burns out, the IC is history. ...... Phil |
#3
Posted to sci.electronics.repair
|
|||
|
|||
STR-W6000S power IC
On Saturday, 1 April 2017 19:21:46 UTC, wrote:
l am working on a refrigerator board which uses STR-W6000S power ic The resistor to pin 3 of the ic is burnt beyond recognition. l tried to find out from the manufacturers data sheet but all the application circuits there have no value marked on the resistors. can anyone give a typical value or how to figure out this value? Thanks l have changed the ic and try that value too |
#4
Posted to sci.electronics.repair
|
|||
|
|||
STR-W6000S power IC
The reference design for that chip shows a 0.27 ohm/1W resistor. Select a
low inductance type such as a carbon composition resistor here... definitely not a wirewound type. http://pdf1.alldatasheet.com/datashe...TR-W6000S.html Cheers, Dave M wrote: On Saturday, 1 April 2017 19:21:46 UTC, wrote: l am working on a refrigerator board which uses STR-W6000S power ic The resistor to pin 3 of the ic is burnt beyond recognition. l tried to find out from the manufacturers data sheet but all the application circuits there have no value marked on the resistors. can anyone give a typical value or how to figure out this value? Thanks l have changed the ic and try that value too |
#5
Posted to sci.electronics.repair
|
|||
|
|||
STR-W6000S power IC
On Sunday, April 2, 2017 at 3:30:43 PM UTC-4, Dave M wrote:
The reference design for that chip shows a 0.27 ohm/1W resistor. Select a low inductance type such as a carbon composition resistor here... definitely not a wirewound type. http://pdf1.alldatasheet.com/datashe...TR-W6000S.html Cheers, Dave M wrote: On Saturday, 1 April 2017 19:21:46 UTC, wrote: l am working on a refrigerator board which uses STR-W6000S power ic The resistor to pin 3 of the ic is burnt beyond recognition. l tried to find out from the manufacturers data sheet but all the application circuits there have no value marked on the resistors. can anyone give a typical value or how to figure out this value? Thanks l have changed the ic and try that value too You definitely should spec a low inductance type for the source resistor at these freq, but even certain carbon comps are supposedly trimmed in a spiral pattern making them inductive.. There are non inductive types available but they're tough to find. Still, I'd try any resistor before a wirewound in this app. |
#6
Posted to sci.electronics.repair
|
|||
|
|||
STR-W6000S power IC
Dave M wrote:
The reference design for that chip shows a 0.27 ohm/1W resistor. Select a low inductance type such as a carbon composition resistor here... definitely not a wirewound type. ** Good advice, but where do you get carbon composition resistors in that value? The IC will operate fine with readily available metal film types. And beware, there are some wire wound types that look *exactly* like metal film ones. I was fooled by this once and the PSU would not start up normally. ..... Phil |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Halfords switching power supply to power a Ring Automotive RAC610 12V Analogue (Tyre) Compressor | UK diy | |||
Does an iPad or high power Android phone *need* a USB 3.0 extensionfor full power charging? | Electronics Repair | |||
Deteriorated Power Line Coming into House from Power Meter | Home Repair | |||
HP/Agilent E3632A programmable power supply has power up failure (solution) | Electronics Repair | |||
Running 120v small power tool on UK 230v power (with pics) | Electronics Repair |