Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 408
Default Help Google search Oscilloscope

Would like to hook up my newish Rigol 4 channel scope to analyze ignition in my 1948 Pontiac. Need hookup and safety information.
Entering "lab scope ignition testing" etc. leads to hundreds of links but they are ALL automotive scopes e.g. Sun, Snap-On etc. They all claim the words "lab scope".

Could anybody suggest a better search term.
All responses greatly appreciated.

Ivan Vegvary
  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,625
Default Help Google search Oscilloscope

On Wednesday, October 26, 2016 at 3:55:56 PM UTC-4, Ivan Vegvary wrote:
Would like to hook up my newish Rigol 4 channel scope to analyze ignition in my 1948 Pontiac. Need hookup and safety information.
Entering "lab scope ignition testing" etc. leads to hundreds of links but they are ALL automotive scopes e.g. Sun, Snap-On etc. They all claim the words "lab scope".

Could anybody suggest a better search term.
All responses greatly appreciated.

Ivan Vegvary


  #3   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,625
Default Help Google search Oscilloscope

On Wednesday, October 26, 2016 at 3:55:56 PM UTC-4, Ivan Vegvary wrote:
Would like to hook up my newish Rigol 4 channel scope to analyze ignition in my 1948 Pontiac. Need hookup and safety information.
Entering "lab scope ignition testing" etc. leads to hundreds of links but they are ALL automotive scopes e.g. Sun, Snap-On etc. They all claim the words "lab scope".

Could anybody suggest a better search term.
All responses greatly appreciated.

Ivan Vegvary


file:///C:/Users/pweick/Downloads/ETI_Feb77_ScopeTheIgnition_1b.pdf

http://int.rigol.com/Applications/Car/?lc=EN

Would these help?

Peter Wieck
Melrose Park, PA

I am not a member of any organized political party. I am a Democrat.

Will Rogers
  #4   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 408
Default Help Google search Oscilloscope

Thank you PF.
The link does tell me what is possible. I suppose by 'high pressure pdobe' they mean 'high voltage.
Hookup diagrams would be nice to have.
Of course the only electronics in a 1948 auto is the ignition system.
Would love to look at 4 cylinders (8 total) at a time with the Rigol.
I do have inductive pickups that I can salvage from timing lights.
  #5   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,243
Default Help Google search Oscilloscope

On 10/26/2016 1:43 PM, Ivan Vegvary wrote:
Thank you PF.
The link does tell me what is possible. I suppose by 'high pressure pdobe' they mean 'high voltage.
Hookup diagrams would be nice to have.
Of course the only electronics in a 1948 auto is the ignition system.
Would love to look at 4 cylinders (8 total) at a time with the Rigol.
I do have inductive pickups that I can salvage from timing lights.

Exactly what do you expect to see?
What are you gonna do with the information when you get it?

Is the benefit derived from that worth the risk of blasting
the front-end out of your scope?

What you see on the scope is likely to be more dependent
on your probing technique than the signals present.
When I experimented with monitoring fuel injection,
I had trouble getting rid of the ignition noise so I could look
at the injectors.

I have a Snap-On automotive scope with an input voltage
rating of 500V with 30KV surge rating, whatever that means.
I wouldn't go poking around aimlessly with that either.
I'm sure it's completely safe...except when it isn't.

Keep your digital scope out of your car unless you really, really
need to measure something that you can control to FIX something that's
broke.
Even the 12V...I guess it was 6V in 1948...electrical system is risky.

http://www.littelfuse.com/data/en/Ap...tes/an9312.pdf


  #6   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 408
Default Help Google search Oscilloscope

On Wednesday, October 26, 2016 at 3:12:34 PM UTC-7, mike wrote:
On 10/26/2016 1:43 PM, Ivan Vegvary wrote:
Thank you PF.
The link does tell me what is possible. I suppose by 'high pressure pdobe' they mean 'high voltage.
Hookup diagrams would be nice to have.
Of course the only electronics in a 1948 auto is the ignition system.
Would love to look at 4 cylinders (8 total) at a time with the Rigol.
I do have inductive pickups that I can salvage from timing lights.

Exactly what do you expect to see?
What are you gonna do with the information when you get it?

Is the benefit derived from that worth the risk of blasting
the front-end out of your scope?

What you see on the scope is likely to be more dependent
on your probing technique than the signals present.
When I experimented with monitoring fuel injection,
I had trouble getting rid of the ignition noise so I could look
at the injectors.

I have a Snap-On automotive scope with an input voltage
rating of 500V with 30KV surge rating, whatever that means.
I wouldn't go poking around aimlessly with that either.
I'm sure it's completely safe...except when it isn't.

Keep your digital scope out of your car unless you really, really
need to measure something that you can control to FIX something that's
broke.
Even the 12V...I guess it was 6V in 1948...electrical system is risky.

http://www.littelfuse.com/data/en/Ap...tes/an9312.pdf


Thanks Mike,
I thought if I could see all the ignition activity at the same time (or at least 4 at a time) I could look for anomalies and identify a poorly firing spark plug or semi-faulty wire.

Thanks for the cautionary note. Will heed.

Ivan Vegvary
  #7   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,017
Default Help Google search Oscilloscope

On Wednesday, October 26, 2016 at 3:19:48 PM UTC-7, Ivan Vegvary wrote:

I thought if I could see all the ignition activity at the same time (or at least 4 at a time) I could look for anomalies and identify a poorly firing spark plug or semi-faulty wire.



Yep, the low-voltage terminal of a spark coil does give that kind of info.
You can identify (or so I'm told) variations in fuel mixture from cylinder to
cylinder that way (higher breakdown voltage for rich fuel mixture). It
takes a 500V scale for the o'scope, though ('low voltage' means +12 to
minus 300 or so...).
A transformer clip-on probe can trigger your 'scope from cylinder
1, which simplifies the analysis if your auto has a single coil for all the
cylinders.
  #8   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,243
Default Help Google search Oscilloscope

On 10/26/2016 5:41 PM, whit3rd wrote:
On Wednesday, October 26, 2016 at 3:19:48 PM UTC-7, Ivan Vegvary wrote:

I thought if I could see all the ignition activity at the same time


(or at least 4 at a time) I could look for anomalies and identify a

poorly firing spark plug or semi-faulty wire.


Yep, the low-voltage terminal of a spark coil does give that kind of info.
You can identify (or so I'm told) variations in fuel mixture from cylinder to
cylinder that way (higher breakdown voltage for rich fuel mixture). It
takes a 500V scale for the o'scope, though ('low voltage' means +12 to
minus 300 or so...)
A transformer clip-on probe can trigger your 'scope from cylinder
1, which simplifies the analysis if your auto has a single coil for all the
cylinders.

You have to be careful NOT to assume normal conditions when detecting
faults, which by definition, are NOT normal conditions. Stuff happens.
It's best if that stuff doesn't happen when you're probing around
with an expensive digital scope.

300V might be a fine number under normal circumstances, but,
if a wire is bad and the plug fires at a much higher coil
secondary voltage, the primary may also show a much bigger spike.
And there's always the temptation to crank up the sensitivity
to see some smaller wiggle on the trace. That may be a bad idea
in this case.

A plug either fires or it doesn't. If it fires, the thing you
are interested in is the current. After it arcs, the voltage
will be determined by the plug and wire/coil resistance/inductance.
High current fat spark good. Of course, that assumes
that the current is all going thru the plug and not arcing
to ground thru a crack in wire insulation.

If you have a clip-on current probe of known transient response,
you can clip it on the coil output and look at the relative currents
for all the cylinders. Properly insulated current probe designed
for ignition service should be safe to use on your scope.
If you try to move the probe to different plug wires, you'll probably
see more variation in the coupling than in the actual signal.

It's a vintage car. If it runs, drive it proudly.
If it runs like it has ignition problems, change the plugs. If that
doesn't fix it, work your way back toward the battery.
Run it in the dark and poke around the wires with a grounded
probe to look for insulation faults. You can learn some
interesting things by pulsing the coil with the engine off
and listening to the coil. But, you can smoke the coil if you're not
careful.

Rule number one...
If it ain't broke, don't try to fix it using your expensive scope.
Rule number two...
If it IS broke, don't try to fix it using your expensive scope,
except as a last resort.



  #9   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 133
Default Help Google search Oscilloscope

Ivan Vegvary wrote:

I thought if I could see all the ignition activity at the same time (or at
least 4 at a time) I could look for anomalies and identify a poorly firing
spark plug or semi-faulty wire.


Ok but it still begs the question, why?

I can't see a set of new plugs, wires, cap, rotor, points and condenser
running more than $50 dollars or so. I'd just replace everything and if you
think something is wrong, look elsewhere.

You didn't say where and what condition this car is in, but time and money
spent on a compression test and carb rebuild kit wouldn't be money ill
spent. That and a timing light.

It's a novel idea but the scope isn't going to give you any more ideas than
a good set of ears and eyes will.

-bruce



  #10   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 408
Default Help Google search Oscilloscope

Thank you all. Scope will not be used on ignition. Car runs fine. Lesson(s) learned. Great group!
Ivan Vegvary


  #12   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 4,045
Default Help Google search Oscilloscope

On Wed, 26 Oct 2016 12:55:53 -0700 (PDT), Ivan Vegvary
wrote:

Would like to hook up my newish Rigol 4 channel scope to analyze ignition in my 1948 Pontiac. Need hookup and safety information.
Entering "lab scope ignition testing" etc. leads to hundreds of links but they are ALL automotive scopes e.g. Sun, Snap-On etc. They all claim the words "lab scope".

Could anybody suggest a better search term.
All responses greatly appreciated.


One of my customers uses one of these:
http://www.ebay.com/itm/Hantek-Virtual-Oscilloscope-8CH-Programmable-Generator-CE-Auto-Ignition-Probe-/140921187522
http://www.hantek.com/en/ProductDetail_136.html
http://www.hantek.com/en/ProductDetail_56.html

The couplers are pricy:
http://www.ebay.com/itm/7pcs-HT-25-Auto-Ignition-Probe-For-Hantek-Automotive-Diagnostic-Oscilloscope-/140855478422
http://www.ebay.com/sch/i.html?_nkw=8+ignition+probes
http://www.hantek.com/en/ProductDetail_15_11165.html
Note that these are for "coil on plug" type engines, which are
unlikely to be found on a 1948 Pontiac.

Maybe a coupler or ignition probe like one of these:
https://www.pinterest.com/ADPTraining/scope-1-automotive-engine-analyzer-oscilloscope/
https://s-media-cache-ak0.pinimg.com/originals/2a/ee/3b/2aee3b18361772ee3ebbc98973cbf2e3.jpg


--
Jeff Liebermann
150 Felker St #D
http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558
  #13   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,630
Default Help Google search Oscilloscope

On Thursday, October 27, 2016 at 8:08:11 AM UTC-5, Ivan Vegvary wrote:
Thank you all. Scope will not be used on ignition. Car runs fine. Lesson(s) learned. Great group!
Ivan Vegvary


This is one of those times when an old CRO would come in handy. A 20 MHz job from the 1970s would be fine.

You would connect the vertical input to where the wires goes from the points/condenser to the coil. The other channel you use to trigger by loose coupling to cylinder #1.

Set the time base so you see eight pulses if it has a eight cylinder. They should all be the same amplitude. If some are higher the gap of the plug might be wider or the wire starting to fail. If some are lower that would indicate a spark leak, like loss of insulation or a fouled/semi fouled plug.

Once you eliminate all ignition faults having the plug gaps all the same and the wires all good, then if there are variations in the pulses that indicates the relative compression of that cylinder. A cylinder with low compression will yield a lower amplitude pulse if all other things are equal.

I don't remember what kind of voltage you get to the coil on one of those but I think it was around 300 volts. Many newer scopes only go up to 5V/div which with a 10X probe (always use a 10X probe to protect the front end, unless you REALLY need all that gain) gets you to 50V/div. You can go into "UNCAL" mode if it goes off the screen but you are at the upper limit of the front end of the scope now.

You can experiment with it by slowly pulling off one of the wires from the distributor. Don't pull it from the plug itself - I learned that the hard way. ZZZAPP !

You should see the pulse for that cylinder increase in amplitude. Take a wire and short the output of the distributor for that cylinder to ground and the amplitude will decrease. Don't let the thing run alot with o plug wire or anything on the distributor because those coils are current operated. When there is no arc the voltage tries to climb until there is a load and it might break down the insulative properties of the distributor cap or rotor. (this is even more important on newer cars)

Actually the easiest way to find a spark leak is a AM radio. Tue to the lower end of the dial and listen to the ZZZZZZZ sound which will increase in pitch as you rev the engine. But if you get a POP POP POP sound that means you probably need wires or a distributor cap. The does not tell you which cylinder but it doesn't matter, the wires should be changed as a set and the distributor cap is common to all so that is that.

The one time I ever used a scope on a car was a 1990 Olds with a VIN C 3800.. It stalled sometimes when hot and would not restart. The way it acted smelled like a semiconductor fault and sure enough the crank sensor was failing. We read up on how the system works and I stuck the scope probe where it needed to be. A garage would have taken a month to fix this but we were flipping cars at the time. I used to have a couple thousand worth of books on it but later sold them because I don't do that kind of work anymore for a couple of reasons.

Anyway, does that old Pontiac have a radio in it ? Now that can be a blast. You're looking at tubes ad a vibrator based B+ supply. I assume it is 6 volts, right ?

What can blow some people's mind is that those cars and even the radio will work if you put the battery in backward. It has been known to happen actually, that is why they used to polarize the generator. But they didn't really have to, nothing cared much about polarity. Even the radio, because the vibrator changed it to AC for a transformer the rectifier(s) after that took care of polarity, the filaments of the tubes don't care.

I think it did make a little bit of difference in the spark, but minor. The problem comes when you need or give a jumpstart. Sometimes you get that big spark and then you know that one or the other car is mis-polarized.

Later came the hybrid radios with the solid state output, then polarity became important, also then the alternator came out and it was not an issue anymore. It simply wouldn't run on reverse polarity because the diodes would short out the battery. In cars with a generator the charging current went through the ignition switch, or else the coils would discharge the batter forthwith. Therefore it was not a good idea to leave it on, to play the radio for example. then they came out with the "ACC" position on the ignition switch. It also wouldn't heat up the points if they happened to be closed.

While I greatly prefer 1960s and 1970s cars it is still a good thing to keep that old beast running.

I drove a 1950 Chevy once, it was almost like work. People don't know how good they got it now. They have no idea what it means to double clutch, and they have no idea how undeveloped the steering and suspension was back then.. Driving those old cars is almost like driving a semi truck, but the new ones aren't even that hard.

Well OK, it isn't really all that difficult but I bet you don't take that thing to work every day...
  #14   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,630
Default Help Google search Oscilloscope

"It's a novel idea but the scope isn't going to give you any more ideas than
a good set of ears and eyes will. "


One thing a hillbilly taught me was if you have a miss and want to know which cylinder it is to put your hand on or near the exhaust manifold (depending on how long it ran) and one part of it will be cooler than the rest.

Another backyard mechanic taught me about timing chains. Take off a valve cover ad see how far backwards you have to turn the crank (with a wrench) to get the valves to move, more than a certain amount the needs timing irons.

The olman taught me that when an engine jumps time the cam is almost always late in phase which will give you higher measured compression but low vacuum. However that has changed because almost all cars use a tensioner. Some of them jump at shutdown and could be advanced instead. Sometimes it is the tensioner that goes bad.

The buddy who taught me about the timing chain trick actually brought a car to me after it had been to Mr Goodwrench and they said "Replace the engine". It was down to cam timing or the crank sensor which was terribly hard to replace in that model. It was running like **** and pretty much couldn't get out of its own way.

I looked at it and drove it and did not know much, just that it ran like ****. Eventually I removed the cover from the throttle body to see if it was getting a good stream of fuel. Well it was but when I tried to rev it up it spouted gas right out. I said "Tear down for timing chain". He said Mr Goodwrench said there is no timing chain, this old 151-4 has gears. The next day he shows up at my house with a broken timing chain tensioner.

Think Mr Goodwrench would give him back the fifty bucks they charged to misdiagnose the thing ? Hell no.

In my business you had hell to pay for a misdiagnosis. apparently the ASE certification males you like a doctor, you get paid even if the patient dies.. Buncha **** IMO.

  #17   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,017
Default Help Google search Oscilloscope

On Wednesday, October 26, 2016 at 7:39:48 PM UTC-7, mike wrote:
On 10/26/2016 5:41 PM, whit3rd wrote:


{about displaying ignition on an oscilloscope]

You can identify (or so I'm told) variations in fuel mixture from cylinder to
cylinder that way (higher breakdown voltage for rich fuel mixture). It
takes a 500V scale for the o'scope, though ('low voltage' means +12 to
minus 300 or so...)


You have to be careful NOT to assume normal conditions when detecting
faults, which by definition, are NOT normal conditions. Stuff happens.


No '500V' scale on an oscilloscope is gonna burn up with a brief transient,
nor can such transients get over 1 kV (the distributor or coil would arc). Probes,
on the other hand, are at risk. You'd be best served by a suitable divider probe,
they exist. Or, a few cheap parts and you've made one.

A plug either fires or it doesn't. If it fires, the thing you
are interested in is the current.


Not true; probing the current is no less dangerous, stick with the V-versus-time
and there's plenty of information present.
More important, a dirty or worn spark plug might eventually pass the right
amount of current, it matters what peak voltage it fires at, You'd be remiss
in disregarding the voltage rise before conduction.


Rule number one...
If it ain't broke, don't try to fix it using your expensive scope.


Gotta disagree strongly there. If you never 'scope out a working car,
the diagnosis of a nonworking one is forever beyond your experience.

  #18   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,148
Default Help Google search Oscilloscope

Bruce Esquibel wrote:



I can't see a set of new plugs, wires, cap, rotor, points and condenser
running more than $50 dollars or so. I'd just replace everything and if
you think something is wrong, look elsewhere.

Oh, wow, have you bought any car parts lately? A set of wires ONLY for a 4-
cylinder car can run $50 at the NAPA parts store. Parts for a 1948 car are
likely to be VERY hard to find specialty items. IF J. C. Whitney doesn't
have them, you could be out of luck.

The guys at the local Auto Zone would not even know what the term "points
and condenser" means.

Jon
  #19   Report Post  
Posted to sci.electronics.repair
tom tom is offline
external usenet poster
 
Posts: 46
Default Help Google search Oscilloscope


"Ivan Vegvary" wrote in message
...
Thank you PF.
The link does tell me what is possible. I suppose by 'high pressure pdobe'
they mean 'high voltage.
Hookup diagrams would be nice to have.
Of course the only electronics in a 1948 auto is the ignition system.
Would love to look at 4 cylinders (8 total) at a time with the Rigol.
I do have inductive pickups that I can salvage from timing lights.


For working around car ignition systems, I would look for one of the older
tube type Tektronix models. Try 535, 545 for the large ones or a 453 with
the nuvistor tubes in the vertical front end.

These would survive better than a usual fet input amp.

Just my 2 cents.



  #20   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 133
Default Help Google search Oscilloscope

Jon Elson wrote:

Oh, wow, have you bought any car parts lately? A set of wires ONLY for a 4-
cylinder car can run $50 at the NAPA parts store. Parts for a 1948 car are
likely to be VERY hard to find specialty items. IF J. C. Whitney doesn't
have them, you could be out of luck.


The guys at the local Auto Zone would not even know what the term "points
and condenser" means.


Yeah but if you expand your horizons a bit beyond NAPA and AutoZones, there
are places like Rockauto.com, which is probably 1 stop shopping for it.

He never mentioned models and engine types but I just looked up a 1948
Pontiac Streamliner with a 3.9L (239 cid) L6...

condenser is $1.31 to $8.52
dist cap $8.72
rotor $3.12 to $4.78
points $9.64 to $12.29
ignition coil $10.11 to $14.56
spark plugs $1.10 to $1.90 each

I don't see wires listed for those in 1948 but, those are just wires.
Looking up a 1964 Buick Wildcat, 425cu 8cyl (at random), they have closeout
sets from $6.74 to high performance ones with ceramic boots, $73.89.

So maybe $50 was on the light side, so if I say under $100 make you feel
better?

Point is, it would be money more well spent just replacing all that compared
to doing whatever he wanted to do with the scope, which probably isn't going
to tell him anything.

Like someone else pointed out, a dwell meter (forgot about those), timing
light and volt-ohm-meter will be far more useful.

-bruce



  #22   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 133
Default Help Google search Oscilloscope

Ralph Mowery wrote:

I have not had a car with points in it in many years so may be way off
on the following.


Wasn't the usual thing to change out the points, condenser, plugs and a
few other things about every 10,000 miles or so back then ?


Yes.

That's really the reason this bit about using some scope to monitor/examine
the ignition system is borderline silly. It wouldn't matter if that car was
some "barn find" where it's been under a bundle of hay for the past 50 years
or a daily driver that someone was using for weekend tours of the
countryside, those parts were part of the normal maintance schedule and
should be totally replaced on a regular basis.

It would be surprising that the engine shouldn't be rebuilt every 25,000
miles as well. Most pre-WW2 cars from the 20's and 30's barely made the
10,000-12,000 mile range before needing a rebuild. Most of those didn't have
oil filters, there used to be kits to use rolls of toilet paper as a
replaceable cartridge.

The post war ones were better but no where near todays standards. Even into
the early 60's, getting into the 50~60,000 mile range was "good". Getting up
to 100,000 without a major overhaul was exceptional.

Something from 1948, if all original, would be a miracle if all it really
needed was the ignition system replaced. It's cheap enough to do and see but
wouldn't suprise me if the rings were gone, crank out of tolerance or even a
lesser job of the cam lobes in the distributor were flat.

All the tech available today isn't going to change the need of getting your
hands greasy.

-bruce

  #23   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,384
Default Help Google search Oscilloscope

Bruce Esquibel wrote:

Jon Elson wrote:

Oh, wow, have you bought any car parts lately? A set of wires ONLY for a
4-
cylinder car can run $50 at the NAPA parts store. Parts for a 1948 car
are
likely to be VERY hard to find specialty items. IF J. C. Whitney doesn't
have them, you could be out of luck.


The guys at the local Auto Zone would not even know what the term "points
and condenser" means.


Yeah but if you expand your horizons a bit beyond NAPA and AutoZones,
there are places like Rockauto.com, which is probably 1 stop shopping for
it.

He never mentioned models and engine types but I just looked up a 1948
Pontiac Streamliner with a 3.9L (239 cid) L6...

condenser is $1.31 to $8.52
dist cap $8.72
rotor $3.12 to $4.78
points $9.64 to $12.29
ignition coil $10.11 to $14.56
spark plugs $1.10 to $1.90 each

I don't see wires listed for those in 1948 but, those are just wires.
Looking up a 1964 Buick Wildcat, 425cu 8cyl (at random), they have
closeout sets from $6.74 to high performance ones with ceramic boots,
$73.89.

WOW, this looks WAY better than any car parts I've bought in the last couple
decades! Maybe they have a bunch of stock left over from 1950 that they are
still selling a couple of per year. Ignition coils run $50, spark plugs are
about $10 each, etc. Haven't had any rotors, points or distributor caps in
some time.

I'd be real cautious driving anything made before 1960 or so, if you hit
anything the steering shaft goes through your chest.

Jon
  #24   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,473
Default Help Google search Oscilloscope

On 10/30/2016 3:27 PM, Jon Elson wrote:
....

I'd be real cautious driving anything made before 1960 or so, if you hit
anything the steering shaft goes through your chest.


That's the 1948 version of a safety feature - it keeps you from driving
recklessly G.

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
OT Need a Google search phrase KenK Home Repair 26 January 12th 15 07:24 PM
Google Search W.T.F. fred[_8_] UK diy 23 May 4th 13 11:19 PM
Google Groups Search Mike Woodworking 35 August 1st 09 02:39 PM
Google search gives a lot of info Earl Woodturning 0 September 11th 05 07:10 AM
search for manual Kenwood oscilloscope CS-6020 or CS-6040 Paul Clinckemalie Electronics Repair 2 March 9th 04 11:16 AM


All times are GMT +1. The time now is 02:52 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"