Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
RV power converter Todd PC40 -- insulator problem
Does anyone have information on or experience with the PC40, 40 amp
converter made by Todd Engineering Sales of Tucson (now out of business)? I'd sure like to get hold of a schematic, but my main interest right now is in identifying the special insulator used under the mosfets. The power supply is used to provide the 12 DC used in recreational travel trailers. It's basically three paralleled SMPS's mounted inside a large aluminum heat sink (which is also the case), one of which, as far as I can tell, is the master. The unit came into my shop with no output. After getting the case opened (it's all pop-riveted) and pulling out the master board, I found the IRF740 mosfet on this board shorted and the resistor next to it open (looks like 0.24 Ohms, 2 Watt -- red, yellow, silver, then gold on a gray body). I also found signs of arcing from the mosfet to the heat sink. The arcing appears to have been through the mosfet's insulator, and that is where I am puzzled. The mosfet, an IRF740 in a TO-220 type case, is insulated from the heat sink by a piece of what at first looks like a standard silicon rubber heat conductive insulator. However, I was attracted to the fact that there is a grounding wire soldered to the insulator. On much closer examination I confirmed that the insulator has a metallic core ("middle of the sandwich"). The point where the heat sink was marked by the arcing corresponds to the narrow edge of the insulator where the metallic core is now exposed. I suspect that the insulator is compromised and should not be reused. But I haven't seen this type of insulation material before and was wondering if anyone has come across it. Is there a description and trade name for it? What about sources? Michael Caplan CET |
#2
|
|||
|
|||
RV power converter Todd PC40 -- insulator problem
Mike,
I am working on the same unit. I am trying to find out the part number of U2 on the main PCB. It is a 3 terminal TO-92 plastic device, it burned up and I can not read the markings.. My unit has a standard insulator, no wire soldered to it. The main board near the large chassis terminal has a spade terminal soldered to the PCB and held in contact with the heatsink with a clip. Also do you know if the telephone type connector is required to turn the unit on. Thanks -- Tony Marsillo Nutmeg Repair ----------------------------------------------------------------- "Michael Caplan" wrote in message ... Does anyone have information on or experience with the PC40, 40 amp converter made by Todd Engineering Sales of Tucson (now out of business)? I'd sure like to get hold of a schematic, but my main interest right now is in identifying the special insulator used under the mosfets. The power supply is used to provide the 12 DC used in recreational travel trailers. It's basically three paralleled SMPS's mounted inside a large aluminum heat sink (which is also the case), one of which, as far as I can tell, is the master. The unit came into my shop with no output. After getting the case opened (it's all pop-riveted) and pulling out the master board, I found the IRF740 mosfet on this board shorted and the resistor next to it open (looks like 0.24 Ohms, 2 Watt -- red, yellow, silver, then gold on a gray body). I also found signs of arcing from the mosfet to the heat sink. The arcing appears to have been through the mosfet's insulator, and that is where I am puzzled. The mosfet, an IRF740 in a TO-220 type case, is insulated from the heat sink by a piece of what at first looks like a standard silicon rubber heat conductive insulator. However, I was attracted to the fact that there is a grounding wire soldered to the insulator. On much closer examination I confirmed that the insulator has a metallic core ("middle of the sandwich"). The point where the heat sink was marked by the arcing corresponds to the narrow edge of the insulator where the metallic core is now exposed. I suspect that the insulator is compromised and should not be reused. But I haven't seen this type of insulation material before and was wondering if anyone has come across it. Is there a description and trade name for it? What about sources? Michael Caplan CET |
#3
|
|||
|
|||
RV power converter Todd PC40 -- insulator problem
Mike,
I am working on the same unit. I am trying to find out the part number of U2 on the main PCB. It is a 3 terminal TO-92 plastic device, it burned up and I can not read the markings.. My unit has a standard insulator, no wire soldered to it. The main board near the large chassis terminal has a spade terminal soldered to the PCB and held in contact with the heatsink with a clip. Also do you know if the telephone type connector is required to turn the unit on. Thanks -- Tony Marsillo Nutmeg Repair ----------------------------------------------------------------- "Michael Caplan" wrote in message ... Does anyone have information on or experience with the PC40, 40 amp converter made by Todd Engineering Sales of Tucson (now out of business)? I'd sure like to get hold of a schematic, but my main interest right now is in identifying the special insulator used under the mosfets. The power supply is used to provide the 12 DC used in recreational travel trailers. It's basically three paralleled SMPS's mounted inside a large aluminum heat sink (which is also the case), one of which, as far as I can tell, is the master. The unit came into my shop with no output. After getting the case opened (it's all pop-riveted) and pulling out the master board, I found the IRF740 mosfet on this board shorted and the resistor next to it open (looks like 0.24 Ohms, 2 Watt -- red, yellow, silver, then gold on a gray body). I also found signs of arcing from the mosfet to the heat sink. The arcing appears to have been through the mosfet's insulator, and that is where I am puzzled. The mosfet, an IRF740 in a TO-220 type case, is insulated from the heat sink by a piece of what at first looks like a standard silicon rubber heat conductive insulator. However, I was attracted to the fact that there is a grounding wire soldered to the insulator. On much closer examination I confirmed that the insulator has a metallic core ("middle of the sandwich"). The point where the heat sink was marked by the arcing corresponds to the narrow edge of the insulator where the metallic core is now exposed. I suspect that the insulator is compromised and should not be reused. But I haven't seen this type of insulation material before and was wondering if anyone has come across it. Is there a description and trade name for it? What about sources? Michael Caplan CET |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Quality Of Tools | UK diy | |||
Motor Phases | Metalworking | |||
power flushing | UK diy | |||
Phase converter balancing | Metalworking |