Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
CD not able to spin
Hi,
I am using AIWA ZKR900 VCD Mini HiFi with 5 CD changer. The player is unable to detect CD but I can hear the optical movement, showing that it is searching for data. The CD seem to trying to spin but it could not take-off. I try to give it a "jump start" by push the CD to spin, then it will spin and the player able to play the CD. So each time now when I want to play a CD, I have to "jump-start" it. What is the actual problem here? Since, it is able to read the CD (provided if the CD can spin), it shows that nothing worng with the optical block. So where can I check for faulty part? Thanks for any help. |
#2
|
|||
|
|||
CD not able to spin
Try some oil down the shaft of the motor. This can most likely be that
the motor must be replaced, or there is a fault in the servo drive to the motor. -- Greetings, Jerry Greenberg GLG Technologies GLG ============================================== WebPage http://www.zoom-one.com Electronics http://www.zoom-one.com/electron.htm Instruments http://www.zoom-one.com/glgtech.htm ============================================== "Alex C" wrote in message m... Hi, I am using AIWA ZKR900 VCD Mini HiFi with 5 CD changer. The player is unable to detect CD but I can hear the optical movement, showing that it is searching for data. The CD seem to trying to spin but it could not take-off. I try to give it a "jump start" by push the CD to spin, then it will spin and the player able to play the CD. So each time now when I want to play a CD, I have to "jump-start" it. What is the actual problem here? Since, it is able to read the CD (provided if the CD can spin), it shows that nothing worng with the optical block. So where can I check for faulty part? Thanks for any help. |
#3
|
|||
|
|||
CD not able to spin
Definitely worth a try cleaning the lens, but if it takes off and spins
pretty reliably with a little "help" this often indicates a shorted spindle motor - that is, shorted on 1/2 it's revolution. Often the short can be cleared if you understand about small motor construction, and can aim some cleaner/lubricant into the little slits underneath, aimed at the brushes, and follow with some compressed air to blow out the debris etc. Repeat a couple times and the short will usually disappear. It's helpful to be able to test for the short before and after so you know if the procedure worked. Mark Z. "Alex C" wrote in message m... Hi, I am using AIWA ZKR900 VCD Mini HiFi with 5 CD changer. The player is unable to detect CD but I can hear the optical movement, showing that it is searching for data. The CD seem to trying to spin but it could not take-off. I try to give it a "jump start" by push the CD to spin, then it will spin and the player able to play the CD. So each time now when I want to play a CD, I have to "jump-start" it. What is the actual problem here? Since, it is able to read the CD (provided if the CD can spin), it shows that nothing worng with the optical block. So where can I check for faulty part? Thanks for any help. |
#4
|
|||
|
|||
CD not able to spin
"Jerry G." writes:
Try some oil down the shaft of the motor. This can most likely be that the motor must be replaced, or there is a fault in the servo drive to the motor. He can hand start it so almost certainly the motor. May be partially shorted needing cleaning or replacement. See the CD repair guide, section on motors. --- sam | Sci.Electronics.Repair FAQ Home Page: http://www.repairfaq.org/ Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/ +Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm | Mirror Site Info: http://www.repairfaq.org/REPAIR/F_mirror.html Important: The email address in this message header may no longer work. To contact me, please use the Feedback Form at repairfaq.org. Thanks. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Washing machine making a loud noise only on spin | UK diy | |||
Hoover 1300 SE Awash performance - no fast spin | UK diy | |||
Indesit WG820 washer - no spin | UK diy | |||
Servis Rain Wave 1100 - stops during spin cycle | UK diy |