Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

Hi all,

Just before I connected up the PSU to this AOR comms rx I'd bought, I
thought I'd best double check the polarity was right, because someone for
some reason had spliced the cable at some time and put a new plug on it.
ON checking, I noted that though the polarity was correct, this psu was
putting out 19.33V - whereas it's rated output was stated as 12V!
This is not some cheap Chinese psu; it's the original AOR Japanese psu
made by them (or at least badged by them) for this receiver. What could
cause it to go from 12 to more than 19V? Don't these wall-wart style
supplies have over-voltage protection/crowbars, FFS??

Just curious...
  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 291
Default PSU gone awry

On Sat, 11 Jul 2015 12:14:27 +0000 (UTC), Cursitor Doom
wrote:

Hi all,

Just before I connected up the PSU to this AOR comms rx I'd bought, I
thought I'd best double check the polarity was right, because someone for
some reason had spliced the cable at some time and put a new plug on it.
ON checking, I noted that though the polarity was correct, this psu was
putting out 19.33V - whereas it's rated output was stated as 12V!
This is not some cheap Chinese psu; it's the original AOR Japanese psu
made by them (or at least badged by them) for this receiver. What could
cause it to go from 12 to more than 19V? Don't these wall-wart style
supplies have over-voltage protection/crowbars, FFS??

Just curious...

Some supplies will not regulate voltage without a load. Try measuring
it again with a small load (eg, a 1K resistor) across the supply.

  #3   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

On Sat, 11 Jul 2015 10:10:40 -0400, Pat wrote:

Some supplies will not regulate voltage without a load. Try measuring
it again with a small load (eg, a 1K resistor) across the supply.


Good point! Still doesn't check-out, though.
Rated current at 12V is 500mA, so a 50 Ohm resistor would be more
appropriate. Managed to find a 47R power resistor and connected across
supply. Now reading 14.45V, so deffo not right...

  #4   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 56
Default PSU gone awry

On 11.07.2015 19:43, Cursitor Doom wrote:
On Sat, 11 Jul 2015 10:10:40 -0400, Pat wrote:

Some supplies will not regulate voltage without a load. Try
measuring it again with a small load (eg, a 1K resistor) across
the supply.


Good point! Still doesn't check-out, though. Rated current at 12V is
500mA, so a 50 Ohm resistor would be more appropriate. Managed to
find a 47R power resistor and connected across supply. Now reading
14.45V, so deffo not right...


AOR Japan - that supply is for a radio, right?

That reminds me of the (maybe similar) power supply of another radio.
Last year I bought a Yupiteru MVT-7500. It's a small handheld radio
with a 100 kHz to 1.3 GHz continuous frequency range, operable from
either 3 AA cells or an external power supply. It came with a linear
PSU, rated for a 100 V AC mains input (Japanese) and a 12V DC output.

At least, 12V DC is what's printed on it. Since I don't have a 100 V
mains socket at home, I couldn't test it right away - had to get a
230 to 2x48 V transformer first, and use the secondaries in series
(96 V nominal) as a practical approximation. Unloaded it happens to
be slightly over 100 V, but should be within usual tolerances. When
I plugged the Yupi's power supply into it and checked the output with
a multimeter (unloaded), it went up over 17 V! At first I thought my
improvised primary supply was iffy, but nope, the primary was OK.

Then I tried loading it and it just barely got near its rated output
under maximum rated load of 200 mA. But since the radio never really
uses the full 200 mA anyway - either 80 or 150 mA depending on the
state of the LCD backlight - the power supply voltage is much higher.
It seems to run at just over 15 V, more or less, under "real life"
conditions and never gets down to 12 V with the radio as a load.

Apparently here the PSU has just a transformer, a bridge rectifier
and a cap - nothing else, all the regulation is done in the radio.

Yours may be similar. Btw, was yours also rated for 100 V and did
you plug it into 115 V by any chance? If so, consider getting it a
"properly" rated supply. The Japanese have a 100 V mains, so when
they write 100 V, they actually mean it. Using the PSU on 115 V
may work, but it could likely stress components in the radio if
connected like this for a significant period of time.

Regards
Dimitrij

  #5   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 818
Default PSU gone awry



"Cursitor Doom" wrote in message ...

Hi all,

Just before I connected up the PSU to this AOR comms rx I'd bought, I
thought I'd best double check the polarity was right, because someone for
some reason had spliced the cable at some time and put a new plug on it.
ON checking, I noted that though the polarity was correct, this psu was
putting out 19.33V - whereas it's rated output was stated as 12V!
This is not some cheap Chinese psu; it's the original AOR Japanese psu
made by them (or at least badged by them) for this receiver. What could
cause it to go from 12 to more than 19V? Don't these wall-wart style
supplies have over-voltage protection/crowbars, FFS??

Just curious...




Just curious, is this Wall Wart just a transformer in a plastic case?
Any 12v transformer unloaded will put out a lot more than its rated voltage.

19v doesn't sound that unlikely to me if that is what it is.


Gareth.



  #6   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 75
Default PSU gone awry

Dimitrij Klingbeil expressed precisely :
On 11.07.2015 19:43, Cursitor Doom wrote:
On Sat, 11 Jul 2015 10:10:40 -0400, Pat wrote:

Some supplies will not regulate voltage without a load. Try
measuring it again with a small load (eg, a 1K resistor) across
the supply.


Good point! Still doesn't check-out, though. Rated current at 12V is
500mA, so a 50 Ohm resistor would be more appropriate. Managed to
find a 47R power resistor and connected across supply. Now reading
14.45V, so deffo not right...


AOR Japan - that supply is for a radio, right?


That reminds me of the (maybe similar) power supply of another radio.
Last year I bought a Yupiteru MVT-7500. It's a small handheld radio
with a 100 kHz to 1.3 GHz continuous frequency range, operable from
either 3 AA cells or an external power supply. It came with a linear
PSU, rated for a 100 V AC mains input (Japanese) and a 12V DC output.


At least, 12V DC is what's printed on it. Since I don't have a 100 V
mains socket at home, I couldn't test it right away - had to get a
230 to 2x48 V transformer first, and use the secondaries in series
(96 V nominal) as a practical approximation. Unloaded it happens to
be slightly over 100 V, but should be within usual tolerances. When
I plugged the Yupi's power supply into it and checked the output with
a multimeter (unloaded), it went up over 17 V! At first I thought my
improvised primary supply was iffy, but nope, the primary was OK.


Then I tried loading it and it just barely got near its rated output
under maximum rated load of 200 mA. But since the radio never really
uses the full 200 mA anyway - either 80 or 150 mA depending on the
state of the LCD backlight - the power supply voltage is much higher.
It seems to run at just over 15 V, more or less, under "real life"
conditions and never gets down to 12 V with the radio as a load.


Apparently here the PSU has just a transformer, a bridge rectifier
and a cap - nothing else, all the regulation is done in the radio.


Yours may be similar. Btw, was yours also rated for 100 V and did
you plug it into 115 V by any chance? If so, consider getting it a
"properly" rated supply. The Japanese have a 100 V mains, so when
they write 100 V, they actually mean it. Using the PSU on 115 V
may work, but it could likely stress components in the radio if
connected like this for a significant period of time.


Regards
Dimitrij


And isn't the nominal in USA 120volts these day? :-Z

The Japanese 100Volts was a problem in the early days of PCs as many
people thought it was the same as USA whereas only military bases had
USA power. Some of Japan is 60 hz and some is 50Hz

--
John G Sydney.
  #7   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

On Sat, 11 Jul 2015 22:42:47 +0100, Gareth Magennis wrote:

Just curious, is this Wall Wart just a transformer in a plastic case?


Eh?? Have you actually read the thread?
  #8   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

On Sat, 11 Jul 2015 22:40:48 +0200, Dimitrij Klingbeil wrote:

AOR Japan - that supply is for a radio, right?


Correct. A "communications receiver" so-called, though it's only the size
of a half a shoebox. I'm more accustomed to rack-mounted Racals so please
forgive my cynicism.

That reminds me of the (maybe similar) power supply of another radio.
Last year I bought a Yupiteru MVT-7500. It's a small handheld radio with
a 100 kHz to 1.3 GHz continuous frequency range, operable from either 3
AA cells or an external power supply. It came with a linear PSU, rated
for a 100 V AC mains input (Japanese) and a 12V DC output.


This one is specifically made for this receiver. It even has the pin-outs
for the rx's power socket printed on it. And it's been manufactured for
the UK market. It states 230VAC input; 12VDC @ 500mA output; 12VA rating.
And, "Made by AOR Communications, Tokyo, Japan" under the spec. Could not
be clearer!
  #9   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 818
Default PSU gone awry



"Cursitor Doom" wrote in message ...

On Sat, 11 Jul 2015 22:42:47 +0100, Gareth Magennis wrote:

Just curious, is this Wall Wart just a transformer in a plastic case?


Eh?? Have you actually read the thread?




OK, so just a transformer with rectifier diodes and a cap, i.e. not
regulated, and not an SMPS.


Gareth.

  #10   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 263
Default PSU gone awry

On Saturday, July 11, 2015 at 1:45:09 PM UTC-4, Cursitor Doom wrote:
On Sat, 11 Jul 2015 10:10:40 -0400, Pat wrote:

Some supplies will not regulate voltage without a load. Try measuring
it again with a small load (eg, a 1K resistor) across the supply.


Good point! Still doesn't check-out, though.
Rated current at 12V is 500mA, so a 50 Ohm resistor would be more
appropriate. Managed to find a 47R power resistor and connected across
supply. Now reading 14.45V, so deffo not right...



If the supply is rated at half amp at 12V, a 27 ohm 10 w resistor will give you a better idea of the supply.

As Gareth pointed out, this is probably just an AC xfr, rectifier, filter. Not a smps and not regulated.

If you're unsure about the radio's capability of internally regulating the input or not loading the supply down sufficiently to keep the voltage in the 12-14v range, then replace it with something more appropriate or add an external series pass 12V regulator IC.



  #11   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

On Sun, 12 Jul 2015 06:21:15 -0700, John-Del wrote:

If the supply is rated at half amp at 12V, a 27 ohm 10 w resistor will
give you a better idea of the supply.


I used 47R because it gives rise to half the rated output current, which
I thought would be about right for a conservative design POV. No decent
designer, surely, is going to specify a 500mA PSU for a load requiring
500mA of current. Absolutely maxed-out!

As Gareth pointed out, this is probably just an AC xfr, rectifier,
filter. Not a smps and not regulated.

If you're unsure about the radio's capability of internally regulating
the input or not loading the supply down sufficiently to keep the
voltage in the 12-14v range, then replace it with something more
appropriate or add an external series pass 12V regulator IC.


I've got it running off a big ol' linear supply at the moment. Just out
of curiosity I'll see how much current it's drawing. Should it turn out
to be only around 150-250mA - as I suspect - then we'll know for sure
that wall wart is f*cked. I reckon if I scoped the PSU output I'd see
pure sine waves!

  #12   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 263
Default PSU gone awry

On Sunday, July 12, 2015 at 10:30:45 AM UTC-4, Cursitor Doom wrote:
On Sun, 12 Jul 2015 06:21:15 -0700, John-Del wrote:

If the supply is rated at half amp at 12V, a 27 ohm 10 w resistor will
give you a better idea of the supply.


I used 47R because it gives rise to half the rated output current, which
I thought would be about right for a conservative design POV. No decent
designer, surely, is going to specify a 500mA PSU for a load requiring
500mA of current. Absolutely maxed-out!


Yeah, but you're missing the point. An unregulated wall wart is rated for the max current that the supply will output no less than 12V.

If your radio has regulators inside that can handle an input of 19.33 volts, then there's no problem. If the radio was designed to run on batteries and/or a regulated supply, then you should definitely go to a regulated supply, or add a post regulator to the wall wart.

  #13   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

On Sun, 12 Jul 2015 08:17:38 -0700, John-Del wrote:

Yeah, but you're missing the point. An unregulated wall wart is rated
for the max current that the supply will output no less than 12V.

If your radio has regulators inside that can handle an input of 19.33
volts, then there's no problem. If the radio was designed to run on
batteries and/or a regulated supply, then you should definitely go to a
regulated supply, or add a post regulator to the wall wart.


The radio at the power connection states it accepts 12VDC and has a
little diagram of the three hole pin-out for polarity/orientation. I find
it absurd that one should expect such a device to be able to cope with
19V in. Call me old fashioned if you like, but that's my mindset. If it
says it requires 12V I'm not going to stick 19V unreg into it. Just
doesn't sit right with me.
I've checked the current this radio draws when supplied with 12V
regulated on full volume with the display on max. etc., etc., and it's
275mA, so a little higher than I expected but not enough to make any
material difference.
*If* that PSU is working as it should then my opinion of Jap design has
just taken a big hit.

  #14   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 2,783
Default PSU gone awry

On Sun, 12 Jul 2015 06:21:15 -0700, John-Del wrote:

As Gareth pointed out, this is probably just an AC xfr, rectifier,
filter. Not a smps and not regulated.


Damn thing's linear! I just took it apart to see and there's only a
trannie, a little full wave rect. and a 25V/1000uF electrolytic in there.
That's all! First thing to do is check that cap....
  #16   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 818
Default PSU gone awry



"John-Del" wrote in message
...

On Sunday, July 12, 2015 at 10:30:45 AM UTC-4, Cursitor Doom wrote:
On Sun, 12 Jul 2015 06:21:15 -0700, John-Del wrote:

If the supply is rated at half amp at 12V, a 27 ohm 10 w resistor will
give you a better idea of the supply.


I used 47R because it gives rise to half the rated output current, which
I thought would be about right for a conservative design POV. No decent
designer, surely, is going to specify a 500mA PSU for a load requiring
500mA of current. Absolutely maxed-out!


Yeah, but you're missing the point. An unregulated wall wart is rated for
the max current that the supply will output no less than 12V.





Further to that, it will (should) be rated to supply at least 12v @ 500mA
when the mains supply voltage is at the legal minimum (not that it is likely
to ever reach that value in the real world).

Currently that is 216.2v. (legal requirement = 230v +10% / -6%)

12v is just the lowest guaranteed voltage this unregulated PSU will deliver
at 500mA, it is not what is normally expected to come out of it.




Gareth.



Gareth.


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT +1. The time now is 04:23 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"