Menu

Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Sherwood RX-5502 Receiver Protection Shutdown, Repair, thoughts wanted...

Page 2 of 2

2

Search this Thread

#41

Report Post

Posted to sci.electronics.repair

John-Del[_2_] John-Del[_2_] is offline

John-Del[_2_] is offline

external usenet poster

Posts: 446

Default

Sherwood RX-5502 Receiver Protection Shutdown, Repair, thoughts wanted...

On Tuesday, March 6, 2018 at 6:51:59 AM UTC-5, wrote:
On Tuesday, 6 March 2018 06:32:03 UTC, Fox's Mercantile wrote:
On 3/6/18 12:16 AM, wrote:
In the end I was lucky to get about $2 an hour for my
time.

Not a very effective use of your time.

No, but we've all had jobs where that became true, more so when young.

NT

Even today I will tackle a job that I know is a loss going in, but with a reason. When I see a circuit board for a problem more than once, I know it's a pattern. Running down a problem on a board with no service data is a nightmare, but once that problem is identified, the next one takes 15 minutes. Much better than paying for a replacement board. The more I see after that the bigger the payoff.

Reply With Quote

Reply With Quote

#42

Report Post

Posted to sci.electronics.repair

Ralph Mowery Ralph Mowery is offline

Ralph Mowery is offline

external usenet poster

Posts: 4,228

Default

Sherwood RX-5502 Receiver Protection Shutdown, Repair, thoughts wanted...

In article ,
says...

Even today I will tackle a job that I know is a loss going in, but with a reason. When I see a circuit board for a problem more than once, I know it's a pattern. Running down a problem on a board with no service data is a nightmare, but once that problem is identified, the next one takes 15 minutes. Much better than paying for
a replacement board. The more I see after that the bigger the payoff.

Someties it works that way. In the 70's I repaired some CB radios for
the locals. Did not charge much as I was partly doing it as a hobby and
building my skills as I had a regular job. I remember one that a dealer
brought to me that I had not worked on before. Took several hours to
repair the problem There was a verticl circuit board that was hard to
run checks on. I finally saw where one of the leads was not soldered.
The dealer brought me 5 or 6 more later, and it only took a short time
to find some leads within an inch of the same place that was not
soldered.

Many items will have one or two problems that if you check those first
it will repair 99% of the problems.

Reply With Quote

Reply With Quote

Page 2 of 2

2

Thread Tools	Search this Thread
Show Printable Version	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Posting Rules
Smilies are On [IMG] code is On HTML code is Off Trackbacks are On Pingbacks are On Refbacks are On

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Sherwood RX-4105/4109 and Insignia NS-R2000 stereo receiver take apart/teardown/exploration	William R. Walsh	Electronics Repair	4	April 4th 10 09:22 PM
Sherwood S-8300Cp receiver help	Wayne Tiffany[_3_]	Electronics Repair	1	January 23rd 09 01:53 PM
Sansui Receiver- Noise at shutdown	Paul	Electronics Repair	5	February 27th 06 11:25 PM
Sony STR-D865 Receiver "Protection" mode	William Buchholz	Electronics Repair	3	November 5th 03 01:12 PM
HV protection for receiver input?	Mark	Electronics Repair	23	August 20th 03 04:29 AM

All times are GMT +1. The time now is 01:24 PM.

About Us

"It's about DIY & home improvement"

Contact Us DIY Banter Forum Home Privacy Statement