Rigol scope LCD problem
DS5102C, color LCD scope. When turned on, the leftmost quarter has
vertical stripes, the affected column is dead. It looks like specific sub-pixels are not responding. R in one row is dead, then G a few rows down, then B, repeat 10 times. http://img593.imageshack.us/i/rigollcdscreen.jpg/ Thing is, after a few hour warm up, it works normally. What is the most likely suspect before I go in and strip it down? Is it likely to be simply a bad harness somewhere that needs reseating? Or do I need to take apart the panel and fiddle arround with something more arcane? I don't think there's zebra strips in these things these days. |
Rigol scope LCD problem
wrote in message
... DS5102C, color LCD scope. When turned on, the leftmost quarter has vertical stripes, the affected column is dead. It looks like specific sub-pixels are not responding. R in one row is dead, then G a few rows down, then B, repeat 10 times. http://img593.imageshack.us/i/rigollcdscreen.jpg/ Thing is, after a few hour warm up, it works normally. What is the most likely suspect before I go in and strip it down? Is it likely to be simply a bad harness somewhere that needs reseating? Or do I need to take apart the panel and fiddle arround with something more arcane? I don't think there's zebra strips in these things these days. I would get inside and lightly probe with fingers, either final bond to the LCD failed somewhere or solder problem on a demultiplexer chip. If bond failure , do not try debonding and rebonding . That plastic reticulated foam, pan scourer, pressed against the suspect area and padded/braced against something is about all you can expect to remedy, unlikely to be zebra strip. |
Rigol scope LCD problem
On Apr 11, 2:41*am, "N_Cook" wrote:
wrote in message ... DS5102C, color LCD scope. When turned on, the leftmost quarter has vertical stripes, the affected column is dead. It looks like specific sub-pixels are not responding. R in one row is dead, then G a few rows down, then B, repeat 10 times. http://img593.imageshack.us/i/rigollcdscreen.jpg/ Thing is, after a few hour warm up, it works normally. What is the most likely suspect before I go in and strip it down? Is it likely to be simply a bad harness somewhere that needs reseating? Or do I need to take apart the panel and fiddle arround with something more arcane? I don't think there's zebra strips in these things these days. I would get inside and lightly probe with fingers, either final bond to the LCD failed somewhere or solder problem on a demultiplexer chip. If bond failure , do not try debonding and rebonding . That plastic reticulated foam, pan scourer, pressed against the suspect area and padded/braced against something is about all you can expect to remedy, unlikely to be zebra strip. Thanks, I haven't taken it apart yet but I think it's just a PS, a mainboard and the front panel with the LCD, BNCs and buttons. I'm hoping a simple reseating will fix it. Thanks for the tips. |
Rigol scope LCD problem
On Mon, 11 Apr 2011 17:42:27 -0400, Jamie
t wrote: Use circuit cooler on suspected areas after warm up to recreate the problem. Good idea, but keep the cooler spray away from the CCFL lamp(s). I sprayed one while it was running and instantly cracked the tube. I don't know if this is a one-time problem, or is typical, but it might pay to be careful. Maybe a hot air gun (on low heat) when the panel is cool, or just massaging the circuitry looking for intermittents, might be equally productive. -- # Jeff Liebermann 150 Felker St #D Santa Cruz CA 95060 # 831-336-2558 # http://802.11junk.com # http://www.LearnByDestroying.com AE6KS |
Rigol scope LCD problem
Jeff Liebermann wrote in
: On Mon, 11 Apr 2011 17:42:27 -0400, Jamie wrote: Use circuit cooler on suspected areas after warm up to recreate the problem. Good idea, but keep the cooler spray away from the CCFL lamp(s). I sprayed one while it was running and instantly cracked the tube. I don't know if this is a one-time problem, or is typical, but it might pay to be careful. Maybe a hot air gun (on low heat) when the panel is cool, or just massaging the circuitry looking for intermittents, might be equally productive. I used to spray the cooler on a Q-tip swab and apply the swab to a suspect component I wanted to chill. or you could rig some short of paper shield to keep the spray away from other parts. -- Jim Yanik jyanik at localnet dot com |
All times are GMT +1. The time now is 10:15 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter