Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to sci.electronics.repair
|
|||
|
|||
Soundcraft series 1600 studio mixer console
24 channel 8 foot long beast with analogue meters and patchbay. Would this
sort of kit be made with convenience of repair in mind. ie props and cable extenders designed in ? Would it be a 2 man job to get it open and propped up, then a partial stripdown just to replace meter bulbs ? Would 2 or 3 of the main channel sections be removable and repairable off site and rest of the console be useable without bridging cables etc |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Soundcraft series 1600 studio mixer console
N_Cook wrote:
24 channel 8 foot long beast with analogue meters and patchbay. Would this sort of kit be made with convenience of repair in mind. ie props and cable extenders designed in ? The internal ribbon cables are too short to allow easy service access to the modules while they are plugged in. While it's possible to work on the modules without removing them from the board, you will want extender cables if you're doing any serious work on them. You can make your own extenders from ribbon cable & standard (3M) ribbon connectors. Would it be a 2 man job to get it open and propped up, then a partial strip down just to replace meter bulbs ? The meter bulbs can be replaced by simply pulling off the meter covers. Would 2 or 3 of the main channel sections be removable and repairable off site and rest of the console be usable without bridging cables etc. ? Like most modular mixers, you can remove most of the input and/or group out modules, and as long as both the main master and aux master modules are left in, the mixer will still work. The 1600 modules are bench repairable, but you will need interface connectors and proper power supplies & test equipment. It's a lot easier to just use extender cables with the console. Soundcraft still has the complete manual for the 1600 on their website: http://www.soundcraft.com/downloads/...d=65#downloads |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Soundcraft series 1600 studio mixer console
Sofa Slug wrote in message
... N_Cook wrote: 24 channel 8 foot long beast with analogue meters and patchbay. Would this sort of kit be made with convenience of repair in mind. ie props and cable extenders designed in ? The internal ribbon cables are too short to allow easy service access to the modules while they are plugged in. While it's possible to work on the modules without removing them from the board, you will want extender cables if you're doing any serious work on them. You can make your own extenders from ribbon cable & standard (3M) ribbon connectors. Would it be a 2 man job to get it open and propped up, then a partial strip down just to replace meter bulbs ? The meter bulbs can be replaced by simply pulling off the meter covers. Would 2 or 3 of the main channel sections be removable and repairable off site and rest of the console be usable without bridging cables etc. ? Like most modular mixers, you can remove most of the input and/or group out modules, and as long as both the main master and aux master modules are left in, the mixer will still work. The 1600 modules are bench repairable, but you will need interface connectors and proper power supplies & test equipment. It's a lot easier to just use extender cables with the console. Soundcraft still has the complete manual for the 1600 on their website: http://www.soundcraft.com/downloads/...d=65#downloads Thanks for all that. The desk is in another country at the moment and I don't know when it will arrive, new owner buying it with some known problems. When it does arrive here I will go fully kitted up with plenty of ribbon and connectors. |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Soundcraft series 1600 studio mixer console
"N_Cook" wrote in message ... 24 channel 8 foot long beast with analogue meters and patchbay. Would this sort of kit be made with convenience of repair in mind. ie props and cable extenders designed in ? Would it be a 2 man job to get it open and propped up, then a partial stripdown just to replace meter bulbs ? Would 2 or 3 of the main channel sections be removable and repairable off site and rest of the console be useable without bridging cables etc All you need to do is on this kind of desk is to remove the first four channel modules. This will give you enough length of ribbon cable/connectors to externally test any channel strip you care to plug into it. You do not need any extenders whatsoever. Similarly with the group modules. You can also remove each channel module and power it on the bench from +/- 15v and ground via the obvious Fuse Resistors. The only thing missing will be Phantom and the Insert loop which you will have to short. Best to work with a schematic in this case though - sometimes grounds may come from more than one source. Gareth. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
SoundCraft Spirit LX-7 Schematic | Electronics Repair | |||
Soundcraft Folio schematic | Electronics Repair |