Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
Hi Guys,
I like to tinker with fixing computers, which seems to often be ripping out a psu and putting a new one in or swapping ram etc. Replacing caps etc I want to be able to test more at the component level and MOSFETs seem to come up a lot. So far the best description of a MOSFET is what I have seen at http://www.youtube.com/watch?v=Te5YYVZiOKs - although maybe on a very simple level I have read the sci.electronicsrepair faq on MOSFET testing but that has me confused as : (a) the tests are all different (b) some of them tell you to put a lead here and a lead there, but not which lead on your DMM (c) I brought a new MOSFET to experiment with - yet I still dont get the same results as some of the tests???? So I have some questions that I hope the experts here can clear up. They all relate to MOSFETs as used in computer PSUs and motherboards 1) Can you test them in circuit 2) I see some are though hole mounted and some are, "surface mounted".Is there a special word to describe teh surface mounted ones? Why are they surface mounted (like lieing flat on PCB) 3) I have been thinking of MOSFETs as a current gate that is turned off/on by voltage - so with respect to all the MOSFETS you see on a computer motherboard near the VRM circuitry - that are they actually doing? how does a bunch of gates help? Any help apreciated in trying to get my head around these things Cheers -Al |
#2
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
"Al" wrote in message ... Hi Guys, I like to tinker with fixing computers, which seems to often be ripping out a psu and putting a new one in or swapping ram etc. Replacing caps etc I want to be able to test more at the component level and MOSFETs seem to come up a lot. So far the best description of a MOSFET is what I have seen at http://www.youtube.com/watch?v=Te5YYVZiOKs - although maybe on a very simple level I have read the sci.electronicsrepair faq on MOSFET testing but that has me confused as : (a) the tests are all different (b) some of them tell you to put a lead here and a lead there, but not which lead on your DMM (c) I brought a new MOSFET to experiment with - yet I still dont get the same results as some of the tests???? So I have some questions that I hope the experts here can clear up. They all relate to MOSFETs as used in computer PSUs and motherboards 1) Can you test them in circuit 2) I see some are though hole mounted and some are, "surface mounted".Is there a special word to describe teh surface mounted ones? Why are they surface mounted (like lieing flat on PCB) 3) I have been thinking of MOSFETs as a current gate that is turned off/on by voltage - so with respect to all the MOSFETS you see on a computer motherboard near the VRM circuitry - that are they actually doing? how does a bunch of gates help? Any help apreciated in trying to get my head around these things Cheers -Al You can do a lot with a battery, LED and resistor. If you apply reverse voltage from drain to source, the "body diode" will conduct and light the LED. (can be useful to identify leadout on small TO92 MOSFETs). Swap the leads around so that the correct polarity is applied to the MOSFET and the degree of conduction will depend on any static charge on the insulated gate. Keep the negative lead on the source and touch the positive lead to the gate to charge the gate capacitance positive, this will make the channel conduct and light the LED. Keep the positive lead on the drain and touch the negative lead on the gate to charge the gate capacitance negative, then any channel conduction means a faulty MOSFET. HTH. |
#3
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
You can do a lot with a battery, LED and resistor.
I have all these parts....;-) If you apply reverse voltage from drain to source, the "body diode" will conduct and light the LED. (can be useful to identify leadout on small TO92 MOSFETs). I am pretty new to this, can you explain what you mean by reverse voltage? +ve terminal to ? and -ve to ? I assume the resistor is just for limiting the current to the LED? Swap the leads around so that the correct polarity is applied to theMOSFET and the degree of conduction will depend on any static charge on the insulated gate. Keep the negative lead on the source and touch the positive lead to the gate to charge the gate capacitance positive, this will make the channel conduct and light the LED. Keep the positive lead on the drain and touch the negative lead on the gate to charge the gate capacitance negative, then any channel conduction means a faultyMOSFET. HTH. Will try that, as soon as I know what you mean by reverse volage. It sounds like there are really no useful test that can be done in circuit? What I have been doing is getting a lot of motherboards and in diode test mode measuring between gate and source. One way it has open circuit, the other way it has a reading of about 790 ohm. This is for the MOSFETs the are around the edge of the CPU as per here (they are 60T03H): http://img188.imageshack.us/i/asus11.jpg/ All mosfets with Black on G Red on S measure 790 Ohm. With Red on G and Black on S they all measure open. The two other MOSFETs are here, near the Vdimm for RAM. They are APM2054N: http://img17.imageshack.us/i/asus12.jpg/ One them ith Black on G and Red on S it takes about 2 seconds to climb to open. With Black on S and Red on G it just measures open. The other with Black on G and Red on S it takes about 2 seconds and climbs to 1466 Ohm. With Black on S and Red on G it just measures open. Does the fact that these two test differently between G and S mean anything or could it be because this is being done in circuit? Cheers -Al |
#4
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
"Al" wrote in message ... You can do a lot with a battery, LED and resistor. I have all these parts....;-) If you apply reverse voltage from drain to source, the "body diode" will conduct and light the LED. (can be useful to identify leadout on small TO92 MOSFETs). I am pretty new to this, can you explain what you mean by reverse voltage? +ve terminal to ? and -ve to ? I assume the resistor is just for limiting the current to the LED? If you need that explaining, you shouldn't be messing with power supplies! - However, what do I care if you kill yourself so here goes. Its best to use a 2mA ultra-efficient LED, the battery should be a MN21/A23 12V car keyfob battery, calculate the resistor to limit the current to suit the LED. Assuming an N-channel MOSFET connecting the negative lead to the drain and the positive lead to the source, the body diode will conduct and light the LED. Next, connect the positive lead to drain and negative to source - the LED may partially light due to static charge on the gate capacitance. Keep the negative lead on the source and touch the positive lead on the gate, this charges the gate capacitance positive and makes the N-channel conduct - so if you then connect the positive lead to drain the LED will light. Next, keep the positive lead on the drain and touch the negative lead to gate, this charges the gate capacitance negative and should make the N-channel completely non-conducting - so put the negative lead on the source and the LED should not even glow the slightest bit - if it does the MOSFET is leaky and will go bang in a PSU! |
#5
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
On Aug 23, 9:55*am, "ian field"
wrote: "Al" wrote in message ... You can do a lot with a battery, LED and resistor. I have all these parts....;-) If you apply reverse voltage from drain to source, the "body diode" will conduct and light the LED. (can be useful to identify leadout on small TO92 MOSFETs). I am pretty new to this, can you explain what you mean by reverse voltage? +ve terminal to ? and -ve to ? I assume the resistor is just for limiting the current to the LED? If you need that explaining, you shouldn't be messing with power supplies! - However, what do I care if you kill yourself so here goes. Its best to use a 2mA ultra-efficient LED, the battery should be a MN21/A23 12V car keyfob battery, calculate the resistor to limit the current to suit the LED. Assuming an N-channelMOSFETconnecting the negative lead to the drain and the positive lead to the source, the body diode will conduct and light the LED. Next, connect the positive lead to drain and negative to source - the LED may partially light due to static charge on the gate capacitance. Keep the negative lead on the source and touch the positive lead on the gate, this charges the gate capacitance positive and makes the N-channel conduct - so if you then connect the positive lead to drain the LED will light. Next, keep the positive lead on the drain and touch the negative lead to gate, this charges the gate capacitance negative and should make the N-channel completely non-conducting - so put the negative lead on the source and the LED should not even glow the slightest bit - if it does theMOSFET is leaky and will go bang in a PSU! Thanks - have done all those tests on a known good mosfet and got the expected results. Now to try some other mosfets whose status is unknown. Cheers -Al |
#6
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
Al wrote in message
... Hi Guys, I like to tinker with fixing computers, which seems to often be ripping out a psu and putting a new one in or swapping ram etc. Replacing caps etc I want to be able to test more at the component level and MOSFETs seem to come up a lot. So far the best description of a MOSFET is what I have seen at http://www.youtube.com/watch?v=Te5YYVZiOKs - although maybe on a very simple level I have read the sci.electronicsrepair faq on MOSFET testing but that has me confused as : (a) the tests are all different (b) some of them tell you to put a lead here and a lead there, but not which lead on your DMM (c) I brought a new MOSFET to experiment with - yet I still dont get the same results as some of the tests???? So I have some questions that I hope the experts here can clear up. They all relate to MOSFETs as used in computer PSUs and motherboards 1) Can you test them in circuit 2) I see some are though hole mounted and some are, "surface mounted".Is there a special word to describe teh surface mounted ones? Why are they surface mounted (like lieing flat on PCB) 3) I have been thinking of MOSFETs as a current gate that is turned off/on by voltage - so with respect to all the MOSFETS you see on a computer motherboard near the VRM circuitry - that are they actually doing? how does a bunch of gates help? Any help apreciated in trying to get my head around these things Cheers -Al Crude basic test for checking MOS Fets , in isolation The following is for n type mosfets and results do vary so it is probably best to try on known good matching FET before falsely discarding a suspect one of same type number. Starting by identifying G,D,S if unknown and assuming starting in non-conducting state. Using a DVM on "diode" check with red and black probes. One pair of terminals only one way round should show a forward voltage x . The black is on the drain (D) the red is on the source (S) leaving the third as the gate. Put red to G and black to D then swap probes to D-S . There should be conductance less than x slowly increasing back to x in the limit. Putting black on the G and red to D then should return D-S to full x value. Or setting the D-S "voltage" to the low setting and just touching the G may reset to the higher "voltage" state. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
#7
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
Crude basic test for checking MOS Fets , in isolation So this test must be done out of circuit? The following is for n type mosfets and results do vary so it is probably best to try on known good matching FET before falsely discarding a suspect one of same type number. Starting by identifying G,D,S if unknown and assuming starting in non-conducting state. Using a DVM on "diode" check with red and black probes. One pair of terminals only one way round should show a forward voltage x . The black is on the drain (D) the red is on the source (S) leaving the third as the gate. Put red to G and black to D then swap probes to D-S . There should be conductance less than x slowly increasing back to x in the limit. Putting black on the G and red to D then should return D-S to full x value. Or setting the D-S "voltage" to the low setting and just touching the G may reset to the higher "voltage" state. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list onhttp://home.graffiti.net/diverse:graffiti.net/ Thanks - will try this. Incidentially what do you use for MOSFET removal from PCB? The type of MOSFET's I am trying to deal with are all mounted "flat" on the PCB of the motherboard. Cheers -Al |
#8
Posted to sci.electronics.repair
|
|||
|
|||
MOSFET help
Al wrote in message
... Crude basic test for checking MOS Fets , in isolation So this test must be done out of circuit? The following is for n type mosfets and results do vary so it is probably best to try on known good matching FET before falsely discarding a suspect one of same type number. Starting by identifying G,D,S if unknown and assuming starting in non-conducting state. Using a DVM on "diode" check with red and black probes. One pair of terminals only one way round should show a forward voltage x .. The black is on the drain (D) the red is on the source (S) leaving the third as the gate. Put red to G and black to D then swap probes to D-S . There should be conductance less than x slowly increasing back to x in the limit. Putting black on the G and red to D then should return D-S to full x value. Or setting the D-S "voltage" to the low setting and just touching the G may reset to the higher "voltage" state. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list onhttp://home.graffiti.net/diverse:graffiti.net/ Thanks - will try this. Incidentially what do you use for MOSFET removal from PCB? The type of MOSFET's I am trying to deal with are all mounted "flat" on the PCB of the motherboard. Cheers -Al test out of circuit, unless comparing known good board to questionable, from the same model, even then depends on circuitry For small ones I tend to score around and angled under a bit, with a scalpel and prize off, pad by pad , with a small jeweller's screwdriver. For larger ones ,I loop some fine nichrome wire under a couple of pins and then ( not owning a micro-jet hot air system) I shroud around the item (to protect surrounding devices) and blast with paint-stripper hot air, tugging at the wires to reduce the heating/loosening time. Blasting the device with freezer spray beforehand, if wishing to salvage undamaged from heat. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Interfacing a power mosfet to a pic running on 3 volts - mosfet drivers.gif (1/1) | Electronic Schematics | |||
Interfacing a power mosfet to a pic running on 3 volts - mosfet drivers.gif (0/1) | Electronic Schematics | |||
SiC Mosfet | Electronics Repair | |||
exploding mosfet | Electronics Repair | |||
Need Help to ID a MOSFET | Electronics Repair |