HP-25 calculator shows all zeros, or blank display
Recently aquired a HP-25 programmable calculator (1975) that had dead
batteries and wouldn't power up correctly. Sometimes the display indicated 12 zeros and other times the display was blank and a few keys would indicate a single "0" in various places. I took the thing apart. cleaned the board and keyboard with alcohol and toothbrush and contact cleaner and managed to get it working for a couple hours using a couple alkaline AA batteries. Put it all back together and everything seemed to work right but the next day it went back to the original erratic operation. I read an article indicating possible noise problems on the data line that was fixed with a 20k resistor termination on some particular line. I tried that idea on a few pins without sucess and cannot get the thing to power up with further cleaning. Haven't looked at the clock signals on a scope yet. Hard to find a schematic for old HP calculators. Any ideas? -Bill |
HP-25 calculator shows all zeros, or blank display
Something that old, certainly by now has some cold solder connections. I
would reflow the whole board, especially if you say alkaline leaked out of the batteries onto the board and the cleaning had some positive effect. If there are any electrolytic capacitors on the board, change them too. "Bill Bowden" wrote in message ... Recently aquired a HP-25 programmable calculator (1975) that had dead batteries and wouldn't power up correctly. Sometimes the display indicated 12 zeros and other times the display was blank and a few keys would indicate a single "0" in various places. I took the thing apart. cleaned the board and keyboard with alcohol and toothbrush and contact cleaner and managed to get it working for a couple hours using a couple alkaline AA batteries. Put it all back together and everything seemed to work right but the next day it went back to the original erratic operation. I read an article indicating possible noise problems on the data line that was fixed with a 20k resistor termination on some particular line. I tried that idea on a few pins without sucess and cannot get the thing to power up with further cleaning. Haven't looked at the clock signals on a scope yet. Hard to find a schematic for old HP calculators. Any ideas? -Bill |
HP-25 calculator shows all zeros, or blank display
On Apr 23, 3:57*pm, Bill Bowden wrote:
Recently aquired a HP-25 programmable calculator (1975) that had dead batteries and *wouldn't power up correctly. Sometimes the display indicated 12 zeros and other times the display was blank and a few keys would indicate a single "0" in various places. I took the thing apart. cleaned the board and keyboard with alcohol and toothbrush and contact cleaner and managed to get it working for a couple hours using a couple alkaline AA batteries. Put it all back together and everything seemed to work right but the next day it went back to the original erratic operation. I read an article indicating possible noise problems on the data line that was fixed with a 20k resistor termination on some particular line. I tried that idea on a few pins without sucess and cannot get the thing to power up with further cleaning. Haven't looked at the clock signals on a scope yet. Hard to find a schematic for old HP calculators. Have you tried the fansite, hpmuseum.org? |
HP-25 calculator shows all zeros, or blank display
On Thu, 23 Apr 2009 15:57:04 -0700 (PDT), Bill Bowden
wrote: Recently aquired a HP-25 programmable calculator (1975) that had dead batteries and wouldn't power up correctly. Sometimes the display indicated 12 zeros and other times the display was blank and a few keys would indicate a single "0" in various places. The battery compartment isn't sealed and the batteries tend to leak corrosive goo into the guts. http://www.hpmuseum.org/hp25.htm http://www.hpmuseum.org/hp25c.htm I took the thing apart. cleaned the board and keyboard with alcohol and toothbrush and contact cleaner and managed to get it working for a couple hours using a couple alkaline AA batteries. Argh. Use NiCad batteries instead. Alkalines have a higher terminal voltage (1.5V) than NiCads (1.35V). I don't know if you can damage anything with the higher voltage, but it doesn't hurt to be safe. If you don't have NiCads, use a bench power supply at 2.70VDC. Contact cleaner leaves an oily residue. That's fine for the slide switches, but not a great idea for the rest of the circuitry. Remove with alcohol. Did you inspect it for any corroded traces, especially near the battery compartment? The various IC's are quite close to the battery section: http://www.hpmuseum.org/25cinter.jpg Cleaning UNDER the IC's is tricky. If there's any corrosion under there, it can be scraped out with a stiff piece of wire shoved under the rows of IC leads. Also, brush between the leads. Put it all back together and everything seemed to work right but the next day it went back to the original erratic operation. Something might be loose or dirty around the clock oscillator area. However, my intuition suggests that it might have something to do with the over-voltage. I read an article indicating possible noise problems on the data line that was fixed with a 20k resistor termination on some particular line. I tried that idea on a few pins without sucess and cannot get the thing to power up with further cleaning. Haven't looked at the clock signals on a scope yet. Hard to find a schematic for old HP calculators. Any ideas? Ask on the HP Museum forums: http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/forum.cgi but first check the archives: http://www.hpmuseum.org/archives.htm -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
HP-25 calculator shows all zeros, or blank display
On Apr 24, 9:33 am, Jeff Liebermann wrote:
On Thu, 23 Apr 2009 15:57:04 -0700 (PDT), Bill Bowden wrote: Recently aquired a HP-25 programmable calculator (1975) that had dead batteries and wouldn't power up correctly. Sometimes the display indicated 12 zeros and other times the display was blank and a few keys would indicate a single "0" in various places. The battery compartment isn't sealed and the batteries tend to leak corrosive goo into the guts. http://www.hpmuseum.org/hp25.htm http://www.hpmuseum.org/hp25c.htm I took the thing apart. cleaned the board and keyboard with alcohol and toothbrush and contact cleaner and managed to get it working for a couple hours using a couple alkaline AA batteries. Argh. Use NiCad batteries instead. Alkalines have a higher terminal voltage (1.5V) than NiCads (1.35V). I don't know if you can damage anything with the higher voltage, but it doesn't hurt to be safe. If you don't have NiCads, use a bench power supply at 2.70VDC. The old alkaline batteries I used measured 2.5 volts DC. Contact cleaner leaves an oily residue. That's fine for the slide switches, but not a great idea for the rest of the circuitry. Remove with alcohol. Did you inspect it for any corroded traces, especially near the battery compartment? The various IC's are quite close to the battery Yes, I inspected every solder joint and trace for problems with a high power magnifying glas. Been doing it for years. section: http://www.hpmuseum.org/25cinter.jpg Cleaning UNDER the IC's is tricky. If there's any corrosion under there, it can be scraped out with a stiff piece of wire shoved under the rows of IC leads. Also, brush between the leads. Put it all back together and everything seemed to work right but the next day it went back to the original erratic operation. Something might be loose or dirty around the clock oscillator area. However, my intuition suggests that it might have something to do with the over-voltage. I read an article indicating possible noise problems on the data line that was fixed with a 20k resistor termination on some particular line. I tried that idea on a few pins without sucess and cannot get the thing to power up with further cleaning. Haven't looked at the clock signals on a scope yet. Hard to find a schematic for old HP calculators. Any ideas? Ask on the HP Museum forums: http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/forum.cgi but first check the archives: http://www.hpmuseum.org/archives.htm -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 I'll do that. Thanks, -Bill |
All times are GMT +1. The time now is 01:26 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter