BenQ TFT Monitor FP2801
 

Hello,

sorry for my poor english, but I'm a German.

I need a service manual for a BenQ TFT Monitor FP2801.

Can't open that thing, 8 screws removed (housing and standoff), but I
can lift the back only for 1/2 mm. There are very strong plastic hooks
visible, but I can't move them.

Any Service Manual and/or hint is welcome.
My replyto: is set and works. Please don't use the fromto:

THX, gracias,

Saludos Wolfgang
--
Meine 7 Sinne:
Unsinn, Schwachsinn, Blödsinn, Wahnsinn, Stumpfsinn, Irrsinn, Lötzinn.
Wolfgang Allinger Paraguay reply Adresse gesetzt !
ca. 15h00..21h00 MEZ SKYPE:wolfgang.allinger

BenQ TFT Monitor FP2801
 

On 03 Mar 2009 11:27:00 -0400, (Wolfgang Allinger)
put finger to keyboard and composed:

I need a service manual for a BenQ TFT Monitor FP2801.

I can't help, but I believe that should be FP2081.

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.

BenQ TFT Monitor FP2081
 

On 04 Mar 09 at group /sci/electronics/repair in article
(Franc Zabkar) wrote:

On 03 Mar 2009 11:27:00 -0400, (Wolfgang Allinger)
put finger to keyboard and composed:

I need a service manual for a BenQ TFT Monitor FP2801.

I can't help, but I believe that should be FP2081.

Thanks, you are right, it#s a FP2081

Saludos Wolfgang
--
Meine 7 Sinne:
Unsinn, Schwachsinn, Blödsinn, Wahnsinn, Stumpfsinn, Irrsinn, Lötzinn.
Wolfgang Allinger Paraguay reply Adresse gesetzt !
ca. 15h00..21h00 MEZ SKYPE:wolfgang.allinger

BenQ TFT Monitor FP2801
 

Saludos Wolfgang
what 'Saludos ' ? Is not spanish ng..


i think there are other screws, have you left away the base?
If you are so sure of not, use a plastic strong thin thing to
sparate parts and lift it , if not you end with a slightly damaged (bumps?)
surface, the hooks are strong right, so you have to lift a bit strong.
lifted one only side and the game is done, i opened a samsung 17"
there was 3 hooks, one really near top, one 3/4 up center the other
3/4 down. Remeber the hooks will be on the front i think, so you
better insist to press to the center the rear cover. bye from Italy..

BenQ TFT Monitor FP2801
 

On 06 Mar 09 at group /sci/electronics/repair in article
(Dav.p.) wrote:

Saludos Wolfgang
what 'Saludos ' ? Is not spanish ng..

Yes, but I'm living now in Paraguay.

i think there are other screws, have you left away the base?
If you are so sure of not, use a plastic strong thin thing to
sparate parts and lift it , if not you end with a slightly damaged
(bumps?) surface, the hooks are strong right, so you have to lift a
bit strong. lifted one only side and the game is done, i opened a
samsung 17" there was 3 hooks, one really near top, one 3/4 up center
the other 3/4 down. Remeber the hooks will be on the front i think, so
you better insist to press to the center the rear cover. bye from
Italy..

I got it open 2 days ago. 4 screw from the fram, 4 screws from the
standoff removed, monitor layed down on the face on a blanket.

The hooks 3 @ each side, 4 @ top and bottom are very strong and couldn't
be bent inside. But they are no sharp edges, just rounded. So with an
8cm width 0.5mm thick palette-knife, I could make enough tension, that
the side hooks slipped out, then top and bottom and more tension, I
lifted the back.

Saludos Wolfgang
--
Meine 7 Sinne:
Unsinn, Schwachsinn, Blödsinn, Wahnsinn, Stumpfsinn, Irrsinn, Lötzinn.
Wolfgang Allinger Paraguay reply Adresse gesetzt !
ca. 15h00..21h00 MEZ SKYPE:wolfgang.allinger