Datasheet needed for Tung-Sol DigiVac DT-1704 Vacuum FluorescentDisplay
 

Hello all, can anyone please help?

I have several Tung-Sol VFD tubes.
They are all P/N DT-1704, but some have the letter A, B, or C, on the
end of the number. (IE: DT-1704B, etc).
Does anyone have a datasheet for these tubes or can you tell me what
the letters designate?
I'm looking for any documentation that describes the difference in the
letter A, B, C used in these part numbers
Thanks, Kevin.

Datasheet needed for Tung-Sol DigiVac DT-1704 Vacuum Fluorescent Display
 

On Mon, 30 Jun 2008 22:41:35 -0700 (PDT), Keinert
put finger to keyboard and composed:

Hello all, can anyone please help?

I have several Tung-Sol VFD tubes.
They are all P/N DT-1704, but some have the letter A, B, or C, on the
end of the number. (IE: DT-1704B, etc).
Does anyone have a datasheet for these tubes or can you tell me what
the letters designate?
I'm looking for any documentation that describes the difference in the
letter A, B, C used in these part numbers
Thanks, Kevin.

Here is an Archer datasheet for the DT-1704:
http://www.tube-tester.com/sites/nix...04_276-063.pdf

No info on suffixes, though. :-(

This appears to be the same datasheet:
http://www.tube-tester.com/sites/nix...04_276-063.zip
http://www.tube-tester.com/sites/nix...B/dt-1730b.htm

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.

Datasheet needed for Tung-Sol DigiVac DT-1704 Vacuum FluorescentDisplay
 

Hi Frank,
Thanks for the links. I had found these on the Internet also, but as
you noticed, they don't explain the difference in the suffix letters.
I am hoping to find someone with an original databook which gives more
info.
Thanks again,
Kevin.

Datasheet needed for Tung-Sol DigiVac DT-1704 Vacuum FluorescentDisplay
 

Keinert wrote:
Hello all, can anyone please help?

I have several Tung-Sol VFD tubes.
They are all P/N DT-1704, but some have the letter A, B, or C, on the
end of the number. (IE: DT-1704B, etc).
Does anyone have a datasheet for these tubes or can you tell me what
the letters designate?
I'm looking for any documentation that describes the difference in the
letter A, B, C used in these part numbers
Thanks, Kevin.

I can't tell you where any documentation is to clarify this question. I
can only offer that perhaps these suffixes denoted slight packaging
differences, or generations. Vacuum tubes added suffixes for such
variations, but the functional specs were almost identical from
generation to generation (unless one used a tube to take advantage of
some specially tweaked parameter in that specific generation)

John

Datasheet needed for Tung-Sol DigiVac DT-1704 Vacuum Fluorescent Display
 

On Tue, 1 Jul 2008 07:37:17 -0700 (PDT), Keinert
put finger to keyboard and composed:

Hi Frank,
Thanks for the links. I had found these on the Internet also, but as
you noticed, they don't explain the difference in the suffix letters.
I am hoping to find someone with an original databook which gives more
info.
Thanks again,
Kevin.

Wikipedia states that Tung-Sol's business was taken over by New Sensor
Corporation:
http://en.wikipedia.org/wiki/Tung_sol

You might like to try contacting them:
http://www.newsensor.com/ContactUs.aspx

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.

Datasheet needed for Tung-Sol DigiVac DT-1704 Vacuum FluorescentDisplay
 

John and Frank,
Thanks for the replies.

If I can verify that the "letter" suffix is a change that does not
affect the operating parameters, then I'm good to go. I only want to
know because I am trying to determine if all suffix numbers all inter-
changeable. In other words, can a DT-1704C be used in place of a
DT-1704B and visa-versa.

Thanks again,
Kevin.