Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 61
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

How can I secure my dishwasher now that it is fixed?
http://www.flickr.com/photos/donnaohl/2337210342/

Every time I shut the door, it moves backward because there's no way I can
get to the screws that were holding it in in the first place.

Is it normal for a dishwasher to be screwed in at the top & then tiled
over?

There are two screws which I had to forcefully wrip out of the plastic of
the top of the dishwasher to work on the dishwasher to unclog the solenoid
filter screen.

It seems that whoever put the dishwasher in, screwed the dishwasher to the
counter from the plywood at the top of the counter BEFORE the tiles were
put in and then tiled over the screws.

The only way I could move the dishwasher was to tear the screws out of the
top of the dishwasher.

Now that the dishwasher is repaired, I have no way to rescrew the screws.

HOW am I supposed to keep the dishwasher from moving back and forth every
time I shut the door?
  #2   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 140
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

On Mar 16, 4:20 pm, Donna Ohl wrote:
How can I secure my dishwasher now that it is fixed?http://www.flickr.com/photos/donnaohl/2337210342/

Every time I shut the door, it moves backward because there's no way I can
get to the screws that were holding it in in the first place.

Is it normal for a dishwasher to be screwed in at the top & then tiled
over?

There are two screws which I had to forcefully wrip out of the plastic of
the top of the dishwasher to work on the dishwasher to unclog the solenoid
filter screen.

It seems that whoever put the dishwasher in, screwed the dishwasher to the
counter from the plywood at the top of the counter BEFORE the tiles were
put in and then tiled over the screws.

The only way I could move the dishwasher was to tear the screws out of the
top of the dishwasher.

Now that the dishwasher is repaired, I have no way to rescrew the screws.

HOW am I supposed to keep the dishwasher from moving back and forth every
time I shut the door?


With any luck, the screws protrude slightly from the bottom of the
countertop wood.
Try using a visegrips or other strong pliers to unscrew them.

If that fails, you could locate the dishwasher lightly forward or back
from the orignal location, and put in a couple new screws. Get some
tough, stainless steel screws so they don't snap.
  #3   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 55
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

Donna Ohl wrote:
How can I secure my dishwasher now that it is fixed?
http://www.flickr.com/photos/donnaohl/2337210342/

Every time I shut the door, it moves backward because there's no way I can
get to the screws that were holding it in in the first place.

Is it normal for a dishwasher to be screwed in at the top & then tiled
over?

There are two screws which I had to forcefully wrip out of the plastic of
the top of the dishwasher to work on the dishwasher to unclog the solenoid
filter screen.

It seems that whoever put the dishwasher in, screwed the dishwasher to the
counter from the plywood at the top of the counter BEFORE the tiles were
put in and then tiled over the screws.

The only way I could move the dishwasher was to tear the screws out of the
top of the dishwasher.

Now that the dishwasher is repaired, I have no way to rescrew the screws.

HOW am I supposed to keep the dishwasher from moving back and forth every
time I shut the door?

About 400mL of Silicone sealant would hold it even through a Tornado !

Yukio YANO
  #4   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 5,823
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)


"Donna Ohl" wrote in message
et...
How can I secure my dishwasher now that it is fixed?
http://www.flickr.com/photos/donnaohl/2337210342/

Every time I shut the door, it moves backward because there's no way I can
get to the screws that were holding it in in the first place.

Is it normal for a dishwasher to be screwed in at the top & then tiled
over?


Absolutely not. There should be a scre or an "L" shaped bracket on the
frront of the DW that gets screwed into the top. Do you still have the
original installation instructions? Or have you tried downloading a copy of
a similar model?



  #5   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 22,192
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Sun, 16 Mar 2008 17:31:10 -0700, Anthony Matonak
wrote:

Donna Ohl wrote:
How can I secure my dishwasher now that it is fixed?
http://www.flickr.com/photos/donnaohl/2337210342/

Every time I shut the door, it moves backward because there's no way I can
get to the screws that were holding it in in the first place.

Is it normal for a dishwasher to be screwed in at the top & then tiled
over?


No, you are missing the under-counter flange or bracket. It's a piece
(or pieces) of metal that is attached to the top of the dishwasher where
your screws were and it sticks out. This lets you screw up into the
bottom of the counter to attach the washer.

Here is a link to a photo showing how one looks, this guy had straps
instead of a single flange but it's the same idea.

http://www.howiesdiy.com/

If you can't find the appropriate part, you could probably fashion
something out of sheet metal or steel straps fairly easily.

Anthony


And, related to the existing screws in the photo, just snip them off
with diagonal cutters.

Use two new screws to secure the washer into the wood counter.


  #6   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 1,199
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

What is the model of your dishwasher? Some like mine have side
mounting screw locations in the event you can't mount it at the top.
For example, if you have granite countertops.
  #7   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 22,192
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Sun, 16 Mar 2008 18:27:05 -0700 (PDT), Mikepier
wrote:

What is the model of your dishwasher? Some like mine have side
mounting screw locations in the event you can't mount it at the top.
For example, if you have granite countertops.


I'm shocked. I have granite and secure the DW into the counter wood,
right below. Never saw a side screw mount method (not excluded).

Two screws and the two brackets.
  #8   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 61
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Sun, 16 Mar 2008 17:31:10 -0700, Anthony Matonak wrote:

you are missing the under-counter flange or bracket.
http://www.howiesdiy.com/


Hi Anthony,
I see what you mean from those photos.

When I look at my dishwasher, I see two indentations at the top
http://www.flickr.com/photos/donnaohl/2337210342/

Those two indentations must be where the missing bracket goes.

I'm guessing that I find those missing brackets at a store but what kind of
store sells dishwasher parts?

Donna
  #9   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 636
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

Donna Ohl wrote:
How can I secure my dishwasher now that it is fixed?
http://www.flickr.com/photos/donnaohl/2337210342/

Every time I shut the door, it moves backward because there's no way
I can get to the screws that were holding it in in the first place.

Is it normal for a dishwasher to be screwed in at the top & then tiled
over?

There are two screws which I had to forcefully wrip out of the
plastic of the top of the dishwasher to work on the dishwasher to
unclog the solenoid filter screen.

It seems that whoever put the dishwasher in, screwed the dishwasher
to the counter from the plywood at the top of the counter BEFORE the
tiles were put in and then tiled over the screws.

The only way I could move the dishwasher was to tear the screws out
of the top of the dishwasher.

Now that the dishwasher is repaired, I have no way to rescrew the
screws.

HOW am I supposed to keep the dishwasher from moving back and forth
every time I shut the door?


Purists should skip the following thought experiement:

If all other alternatives are impossible, you could put a screw through the
body of the dishwasher!

I'd go through the top - less chance of hitting wires - with the correct
length of screw. Then slather a wad of silicone sealant over the exposed
screw head.

Elegant, it ain't, functional it is.



  #10   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 1,572
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)



"Donna Ohl" wrote in message
...
On Sun, 16 Mar 2008 17:31:10 -0700, Anthony Matonak wrote:

you are missing the under-counter flange or bracket.
http://www.howiesdiy.com/


Hi Anthony,
I see what you mean from those photos.

When I look at my dishwasher, I see two indentations at the top
http://www.flickr.com/photos/donnaohl/2337210342/

Those two indentations must be where the missing bracket goes.

I'm guessing that I find those missing brackets at a store but what kind
of
store sells dishwasher parts?

Donna



An appliance store. Look in the phone book, best bet is to find a local mom
& pop place, sometimes they even have some junk units you can get stuff
from. You might also try a hardware store, just find some sort of bracket
that you can bend into the shape you need.




  #11   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 1,199
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

On Mar 16, 10:10*pm, Oren wrote:
On Sun, 16 Mar 2008 18:27:05 -0700 (PDT), Mikepier

wrote:
What is the model of your dishwasher? Some like mine have side
mounting screw locations in the event you can't mount it at the top.
For example, if you have granite countertops.


I'm shocked. I have granite and secure the DW into the counter wood,
right below. Never saw a side screw mount method (not excluded).

Two screws and the two brackets.


If you have granite over wood, then yes you can still top mount it.
But if you just have 1 1/4" granite with no wood underneath, it makes
the side mounting option a good choice.
The GE's like mine have these side holes.
  #12   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
mm mm is offline
external usenet poster
 
Posts: 7,824
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Sun, 16 Mar 2008 19:53:39 -0700, Donna Ohl
wrote:

On Sun, 16 Mar 2008 17:31:10 -0700, Anthony Matonak wrote:

you are missing the under-counter flange or bracket.
http://www.howiesdiy.com/


Hi Anthony,
I see what you mean from those photos.

When I look at my dishwasher, I see two indentations at the top
http://www.flickr.com/photos/donnaohl/2337210342/



I can't really tell much from your picture.


Those two indentations must be where the missing bracket goes.

I'm guessing that I find those missing brackets at a store but what kind of
store sells dishwasher parts?


I'm not sure you need to buy brackets meant for the dishwasher. Any
piece of metal maybe an inch wide by two inches long, depending on
your situation, might work.

Just pull the dishwasher out a little and see if you can find traces
of the original brackets. I'd be suprised if you ripped off the old
brackets entirely, without noticing that.

In my case, I haven't looked at the other end, but there are two
pieces of sheet metal coming out 3/4" at the top, sliding against the
wood counter right above the dishwasher. One screw go up though each
of those pieces of metal to hold the machine in place. There isn't a
lot of force on these screws and they don't have to be longer than 1/2
inch, with a head big enough that it won't go through the hole. Or a
small head with a washer, to keep the head from going through.

Mostly the dishwasher doesn't fall over, but it needs to be fixed in
place so that you don't push the whole thing further in, and so it
doesn't tip over when the racks are sitting on the door and the weight
of the dishes or your leaning on it might make it tip. 1/2 inch
screws are enough for that, but the counter is probably thick enough
3/4 also. If you have to drill a hole in the counter, wrap some black
plastic tape around the drill bit, leaving only the hole depth
showing, so you can tell how far in you have drilled and stop at the
right depth. Don't drill through the plastic part on top.

You can make the bracket out of any piece of metal you're about to
throw away, or anything you see on the street that is metal. You can
use the top of a can of corn. Use tin snips to cut it to fit, or use
gloves to fold it over and a hammer to make the bend nice and flat.
Drill two holes, one to attach it to the dishwasher and one to go up
into the counter top.

Just make sure that where you attach it to the dishwasher, you don't
screw through the top into the "water chamber", where the washing is
done.

You say something about plastic. IfIf there were screws in the
plastic but now the screw holes are real big, maybe thicker screws of
the same length will do it.

If none of this seems likely to work, post back with more details.

posting from alt.home.repair.

Picture 2. It lookks like it is still rubber covered and the rust is
from something that was sitting in the rack. If so, using the machine
a few times might wash away the rust, and if not, maybe a gentle use
of Bon Ami cleanser, of Sof-Scrub, I'm not sure which is better.

If not that, maybe draw a sharp knife with the blade resting on the
rusty stuff, but pulling AWAY from the blade, NOT cutting into the
vinyl. The idea is for the pressure of the blade to bend the
rubber/vinyl and cause the rust, which doesn't bend, to fall off. Why
I think the knife needs to be sharp, I don't know. This method takes
time because one has to make many passes at different angles to get
the whole circumference of the wire.

Donna


  #13   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 283
Default Dishwasher screwed in from the TOP and then tiled over (how to...

Dishwasher, True Story.Between two to three years ago, a divorced woman
whom lived next door to me,,,, She was standing with one foot on the top
of that roll around dish washer, her other foot on a kitchen counter
top, she was trying to remove a kitchen cabinet hinge, she and the other
divorced woman over there were redoing the kitchen and kitchen cabinet
doors.The roll around dish washer tipped, she fell down hard on her left
knee on to the kitchen floor.Whatever you do, never stand on top of a
roll around dish washer.
cuhulin

  #15   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
mm mm is offline
external usenet poster
 
Posts: 7,824
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Sun, 16 Mar 2008 17:07:19 -0800, Oren wrote:

On Sun, 16 Mar 2008 17:31:10 -0700, Anthony Matonak
wrote:

Donna Ohl wrote:
How can I secure my dishwasher now that it is fixed?
http://www.flickr.com/photos/donnaohl/2337210342/

Here is a link to a photo showing how one looks, this guy had straps
instead of a single flange but it's the same idea.

http://www.howiesdiy.com/

If you can't find the appropriate part, you could probably fashion
something out of sheet metal or steel straps fairly easily.

Anthony


And, related to the existing screws in the photo, just snip them off
with diagonal cutters.


You can really cut through screws with wire cutters?? Or what do you
mean by diagonal cutters, that can cut though screws?
Use two new screws to secure the washer into the wood counter.



If you are inclined to email me
for some reason, remove NOPSAM :-)


  #16   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 5,149
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

James Sweet wrote:
"Donna Ohl" wrote in message
...
On Sun, 16 Mar 2008 17:31:10 -0700, Anthony Matonak wrote:

you are missing the under-counter flange or bracket.
http://www.howiesdiy.com/

Hi Anthony,
I see what you mean from those photos.

When I look at my dishwasher, I see two indentations at the top
http://www.flickr.com/photos/donnaohl/2337210342/

Those two indentations must be where the missing bracket goes.

I'm guessing that I find those missing brackets at a store but what kind
of
store sells dishwasher parts?

Donna



An appliance store. Look in the phone book, best bet is to find a local mom
& pop place, sometimes they even have some junk units you can get stuff
from. You might also try a hardware store, just find some sort of bracket
that you can bend into the shape you need.


Any big apartment projects near you? They consider dishwashers
disposable- when one craps out they just swap it out like a light bulb,
and chuck the old one in the dumpster. If you are too shy to dumpster
dive, cruise around and spot the maintenance guy- for the promise of a
10-spot, he would likely hold the next one on his truck and call you to
come fetch it. If it is an entry-level dishwasher, there aren't that
many factories making them, no matter the brand name. Decent odds you
will be able to find one with the same basic design, including the
plastic-covered wire baskets to replace your rusty ones.

--
aem sends...
  #17   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 22,192
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Mon, 17 Mar 2008 18:57:45 -0400, mm
wrote:

And, related to the existing screws in the photo, just snip them off
with diagonal cutters.


You can really cut through screws with wire cutters?? Or what do you
mean by diagonal cutters, that can cut though screws?


Hey! http://www.matcotools.com/ProductImages/spdc3.jpg

Not the best for cutting /breaking a screw, but I've gotten by

My read on the OP was the screws were from the top and then tiled
over... cutting the screw is less damage.

  #18   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 61
Default Dishwasher screwed in from the TOP and then tiled over (how to secure now?)

On Mon, 17 Mar 2008 16:20:43 -0800, Oren wrote:

My read on the OP was the screws were from the top and then tiled
over... cutting the screw is less damage.


Attempting to cut the screws ruined my wire cutters!
Did I use the wrong type?

I tried returning this broken wire cutter to Sears but they didn't have the
EXACT same number ... what good is that supposed "lifetime" warranty!

Anyway, the screws don't seem to do anything now that the plastic in the
top of the dishwasher is broken where they did go in.

Apparently what happened before we bought the house is that the remodelers
screwed the dishwasher in from the top of the then-wood counter before
tiling over the countertop, sealing the top of the screws.

When I lowered the legs of the dishwasher to get it out of its cubbyhole,
the dead weight downward ripped the screws out of the plastic in the top of
the dishwasher leaving ragged holes but no other damage.

So, at this point, the screws don't do anything. I will try to find the
bracket and put that in to hold the dishwasher. That seems like the best
approach recommended.

Donna
  #19   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 929
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

On Mar 17, 9:45 pm, Donna Ohl wrote:
On Mon, 17 Mar 2008 16:20:43 -0800, Oren wrote:
My read on the OP was the screws were from the top and then tiled
over... cutting the screw is less damage.


Attempting to cut the screws ruined my wire cutters!
Did I use the wrong type?

I tried returning this broken wire cutter to Sears but they didn't have the
EXACT same number ... what good is that supposed "lifetime" warranty!

Anyway, the screws don't seem to do anything now that the plastic in the
top of the dishwasher is broken where they did go in.

Apparently what happened before we bought the house is that the remodelers
screwed the dishwasher in from the top of the then-wood counter before
tiling over the countertop, sealing the top of the screws.

When I lowered the legs of the dishwasher to get it out of its cubbyhole,
the dead weight downward ripped the screws out of the plastic in the top of
the dishwasher leaving ragged holes but no other damage.

So, at this point, the screws don't do anything. I will try to find the
bracket and put that in to hold the dishwasher. That seems like the best
approach recommended.

Donna


Donna-

Consider a couple of small dollops of chalk...ones that can be easily
razor knifed through when it comes time to replace the dishwasher.

Maybe there's room for a bracket on the side near the top.

I looked at your photo stream...time to start saving for a re-pipe.
That galvanized pipe must be around 50 years old.

Do those earthquake straps mean you're in e/q country (CA? Bay Area?)

I would suggest a PEX re-pipe.


cheers
Bob
  #20   Report Post  
Posted to alt.home.repair,misc.consumers.frugal-living,sci.electronics.repair
external usenet poster
 
Posts: 533
Default Dishwasher screwed in from the TOP and then tiled over (how tosecure now?)

Donna Ohl wrote:
On Mon, 17 Mar 2008 16:20:43 -0800, Oren wrote:

My read on the OP was the screws were from the top and then tiled
over... cutting the screw is less damage.


Attempting to cut the screws ruined my wire cutters!
Did I use the wrong type?

I tried returning this broken wire cutter to Sears but they didn't have the
EXACT same number ... what good is that supposed "lifetime" warranty!

Anyway, the screws don't seem to do anything now that the plastic in the
top of the dishwasher is broken where they did go in.

Apparently what happened before we bought the house is that the remodelers
screwed the dishwasher in from the top of the then-wood counter before
tiling over the countertop, sealing the top of the screws.

When I lowered the legs of the dishwasher to get it out of its cubbyhole,
the dead weight downward ripped the screws out of the plastic in the top of
the dishwasher leaving ragged holes but no other damage.

So, at this point, the screws don't do anything. I will try to find the
bracket and put that in to hold the dishwasher. That seems like the best
approach recommended.

Donna


Too late now, but hindsight indicates it would have been easier to have
popped out a couple of tiles and grouted them back in after the repair.
Not a difficult job compared to what you did go through.

jak


  #21   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 283
Default Dishwasher screwed in from the TOP and then tiled over (how to...

I have the best dishwasher in town.Her name is Blueberry.
www.cattledog.com www.acdca.org
cuhulin

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
What to secure shingles with runsrealfast Home Repair 14 October 1st 07 04:34 PM
How to secure your network Martha Johnson Electronics Repair 0 November 28th 06 12:31 PM
Secure Investing! Lillie_Steins Woodworking 1 August 10th 06 04:01 PM
secure joints Oldun Woodworking 13 July 21st 05 05:05 PM
Best place to secure a dishwasher? clevere Home Repair 2 April 1st 04 09:23 PM


All times are GMT +1. The time now is 04:26 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"