Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,220
Default Double fan cooling

2 of the same fan blowing air in over the heatsink but there is a noise like
a variable direction wind or slightly gusty wind as though one fan has a
bearing problem.
It would seem one fan is fighting the other to some extent, significant ? or
just one of those things ? .
I was thinking of putting a dividing baffle between the 2.

Disconnecting each in turn and they run perfectly normally with no change of
sound. I may dig out a strobe if i can remember where it is and see if the
blade speed does vary in the double active case.

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/



  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 69
Default Double fan cooling

N Cook wrote:

2 of the same fan blowing air in over the heatsink but there is a noise like
a variable direction wind or slightly gusty wind as though one fan has a
bearing problem.
It would seem one fan is fighting the other to some extent, significant ? or
just one of those things ? .
I was thinking of putting a dividing baffle between the 2.

Disconnecting each in turn and they run perfectly normally with no change of
sound. I may dig out a strobe if i can remember where it is and see if the
blade speed does vary in the double active case.


Beat oscillation. Basically, the normal fan physical noise pitch of the
two fans are _almost_ the same. What you're hearing is the difference between
the two. (it may be less than 1Hz, because the fans will probably be quite
closely matched in noise and speed).

It doesn't cause any harm other than you getting fed up with the noise and
smashing it to bits.

To "fix" the problem, you could try to physically isolate the two fans from
each other (or the common chassis) by using some sponge or rubber or some
such, to help prevent fan vibration getting into the chassis or other fan (if
you have them physically stuck together).

--
Linux Registered User # 302622
http://counter.li.org
  #3   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,220
Default Double fan cooling

John Tserkezis wrote in message
u...
N Cook wrote:

2 of the same fan blowing air in over the heatsink but there is a noise

like
a variable direction wind or slightly gusty wind as though one fan has a
bearing problem.
It would seem one fan is fighting the other to some extent, significant

? or
just one of those things ? .
I was thinking of putting a dividing baffle between the 2.

Disconnecting each in turn and they run perfectly normally with no

change of
sound. I may dig out a strobe if i can remember where it is and see if

the
blade speed does vary in the double active case.


Beat oscillation. Basically, the normal fan physical noise pitch of

the
two fans are _almost_ the same. What you're hearing is the difference

between
the two. (it may be less than 1Hz, because the fans will probably be quite
closely matched in noise and speed).

It doesn't cause any harm other than you getting fed up with the noise

and
smashing it to bits.

To "fix" the problem, you could try to physically isolate the two fans

from
each other (or the common chassis) by using some sponge or rubber or some
such, to help prevent fan vibration getting into the chassis or other fan

(if
you have them physically stuck together).

--
Linux Registered User # 302622
http://counter.li.org


I should have said these are 3inch, 12V dc fans rather than shaded pole
motors so unlikely to match speed that closely. Both are mounted rigidly, no
grommets, to steel chassis and separated by 1.2 inch , the nearest parts of
the heatsink fins are only 3/8 inch from the fan surrounds.
Placing a piece of card between the 2 fans seems to stop the interference
but not desirable in the case of failure of one fan perhaps.

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/


  #4   Report Post  
Posted to sci.electronics.repair
AJ AJ is offline
external usenet poster
 
Posts: 107
Default Double fan cooling

Have you tried reversing one at the mount, using one fan to direct the air
in one direction and the other one directing air the other direction? S.A.
having them both direct air physically away from the heat sink or have one
direct air towards the heat sink and the other removing air from the same
area. Sounds like you are getting a vibration doppler effect due to the
physical operations of both fans in a limited area.
"N Cook" wrote in message
...
John Tserkezis wrote in message
u...
N Cook wrote:

2 of the same fan blowing air in over the heatsink but there is a noise

like
a variable direction wind or slightly gusty wind as though one fan has
a
bearing problem.
It would seem one fan is fighting the other to some extent, significant

? or
just one of those things ? .
I was thinking of putting a dividing baffle between the 2.

Disconnecting each in turn and they run perfectly normally with no

change of
sound. I may dig out a strobe if i can remember where it is and see if

the
blade speed does vary in the double active case.


Beat oscillation. Basically, the normal fan physical noise pitch of

the
two fans are _almost_ the same. What you're hearing is the difference

between
the two. (it may be less than 1Hz, because the fans will probably be
quite
closely matched in noise and speed).

It doesn't cause any harm other than you getting fed up with the noise

and
smashing it to bits.

To "fix" the problem, you could try to physically isolate the two fans

from
each other (or the common chassis) by using some sponge or rubber or some
such, to help prevent fan vibration getting into the chassis or other fan

(if
you have them physically stuck together).

--
Linux Registered User # 302622
http://counter.li.org


I should have said these are 3inch, 12V dc fans rather than shaded pole
motors so unlikely to match speed that closely. Both are mounted rigidly,
no
grommets, to steel chassis and separated by 1.2 inch , the nearest parts
of
the heatsink fins are only 3/8 inch from the fan surrounds.
Placing a piece of card between the 2 fans seems to stop the interference
but not desirable in the case of failure of one fan perhaps.

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/



  #5   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 3,103
Default Double fan cooling

"AJ" wrote in
:

Have you tried reversing one at the mount, using one fan to direct the
air in one direction and the other one directing air the other
direction? S.A. having them both direct air physically away from the
heat sink or have one direct air towards the heat sink and the other
removing air from the same area. Sounds like you are getting a
vibration doppler effect due to the physical operations of both fans
in a limited area. "N Cook" wrote in message
...
John Tserkezis wrote in message
u...
N Cook wrote:

2 of the same fan blowing air in over the heatsink but there is a
noise

like
a variable direction wind or slightly gusty wind as though one fan
has a
bearing problem.
It would seem one fan is fighting the other to some extent,
significant

? or
just one of those things ? .
I was thinking of putting a dividing baffle between the 2.

Disconnecting each in turn and they run perfectly normally with no

change of
sound. I may dig out a strobe if i can remember where it is and
see if

the
blade speed does vary in the double active case.

Beat oscillation. Basically, the normal fan physical noise pitch
of

the
two fans are _almost_ the same. What you're hearing is the
difference

between
the two. (it may be less than 1Hz, because the fans will probably be
quite
closely matched in noise and speed).

It doesn't cause any harm other than you getting fed up with the
noise

and
smashing it to bits.

To "fix" the problem, you could try to physically isolate the two
fans

from
each other (or the common chassis) by using some sponge or rubber or
some such, to help prevent fan vibration getting into the chassis or
other fan

(if
you have them physically stuck together).

--
Linux Registered User # 302622
http://counter.li.org


I should have said these are 3inch, 12V dc fans rather than shaded
pole motors so unlikely to match speed that closely. Both are mounted
rigidly, no
grommets, to steel chassis and separated by 1.2 inch , the nearest
parts of
the heatsink fins are only 3/8 inch from the fan surrounds.
Placing a piece of card between the 2 fans seems to stop the
interference but not desirable in the case of failure of one fan
perhaps.

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/





sounds like a case of the heterodyning fans!

--
Jim Yanik
jyanik
at
kua.net


  #6   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1,220
Default Double fan cooling

Jim Yanik wrote in message
...
"AJ" wrote in
:

Have you tried reversing one at the mount, using one fan to direct the
air in one direction and the other one directing air the other
direction? S.A. having them both direct air physically away from the
heat sink or have one direct air towards the heat sink and the other
removing air from the same area. Sounds like you are getting a
vibration doppler effect due to the physical operations of both fans
in a limited area. "N Cook" wrote in message
...
John Tserkezis wrote in message
u...
N Cook wrote:

2 of the same fan blowing air in over the heatsink but there is a
noise
like
a variable direction wind or slightly gusty wind as though one fan
has a
bearing problem.
It would seem one fan is fighting the other to some extent,
significant
? or
just one of those things ? .
I was thinking of putting a dividing baffle between the 2.

Disconnecting each in turn and they run perfectly normally with no
change of
sound. I may dig out a strobe if i can remember where it is and
see if
the
blade speed does vary in the double active case.

Beat oscillation. Basically, the normal fan physical noise pitch
of
the
two fans are _almost_ the same. What you're hearing is the
difference
between
the two. (it may be less than 1Hz, because the fans will probably be
quite
closely matched in noise and speed).

It doesn't cause any harm other than you getting fed up with the
noise
and
smashing it to bits.

To "fix" the problem, you could try to physically isolate the two
fans
from
each other (or the common chassis) by using some sponge or rubber or
some such, to help prevent fan vibration getting into the chassis or
other fan
(if
you have them physically stuck together).

--
Linux Registered User # 302622
http://counter.li.org

I should have said these are 3inch, 12V dc fans rather than shaded
pole motors so unlikely to match speed that closely. Both are mounted
rigidly, no
grommets, to steel chassis and separated by 1.2 inch , the nearest
parts of
the heatsink fins are only 3/8 inch from the fan surrounds.
Placing a piece of card between the 2 fans seems to stop the
interference but not desirable in the case of failure of one fan
perhaps.

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/





sounds like a case of the heterodyning fans!

--
Jim Yanik
jyanik
at
kua.net


Cor a googlewhack , can I claim the prize.

Both fans are 1/2 inch apart, 3/8 inch from the nearest part of the heatsink
but heatsink channels an inch deep.
Trying a piece of card divider in that 3/8 ins made no difference but the
airflows could still mix in those channels.

--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/




Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
about cooling water pump design for closed circuit and forced circulation cooling tower nawaneet UK diy 2 June 20th 06 10:58 AM
installing double-pane windows: double-sided tape separating from window or window-frame Frank Home Repair 1 May 31st 06 06:02 PM
goodman a/c not cooling [email protected] Home Repair 4 April 21st 06 06:10 AM
A/C--Is It Really Cooling? W. Watson Home Repair 18 July 29th 05 06:52 PM
Cooling a house sPoNiX UK diy 50 June 11th 04 02:53 PM


All times are GMT +1. The time now is 01:09 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"