Strange shrunken capacitor(?)
I have an old Gateway EV700 monitor which shuts down after a few minutes of
use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. |
Strange shrunken capacitor(?)
On Jun 12, 7:47 am, Yattaro wrote:
I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3rhttp://tiny...url.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. Looks like an inductor that was shrink-wrapped and damped against vibration with a bit of either RTV silicon or elephant-snot. Peter Wieck Wyncote, PA |
Strange shrunken capacitor(?)
On Tue, 12 Jun 2007 11:47:53 GMT, Yattaro wrote:
I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. Repeat after me: "Inductor, not capacitor" and you will be OK! |
Strange shrunken capacitor(?)
"Yattaro" wrote in message
et... I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. 1. The "white goo" appears to be hot glue use to hold the component (possibly during wave soldering step) 2. This circuit board has silk-screened legends, such as C102, L302, etc. The first character used to identify this component will tell you what it is: "C" - capacitor, "L" - inductor 3. The component appears to have a polarity stripe, like electrolytic capacitors. 4. IF this is an electrolytic capacitor -- I would replace it based upon it physical condition -- but you would need the correct value and voltage rating! From your photos, really can not tell -- no value markings other than the marking of: LO5G |
Strange shrunken capacitor(?)
"w9gb" wrote in message . .. "Yattaro" wrote in message et... I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. 1. The "white goo" appears to be hot glue use to hold the component (possibly during wave soldering step) 2. This circuit board has silk-screened legends, such as C102, L302, etc. The first character used to identify this component will tell you what it is: "C" - capacitor, "L" - inductor 3. The component appears to have a polarity stripe, like electrolytic capacitors. 4. IF this is an electrolytic capacitor -- I would replace it based upon it physical condition -- but you would need the correct value and voltage rating! From your photos, really can not tell -- no value markings other than the marking of: LO5G Its definitely an inductor - quite likely a linearity coil (polarising stripe is an obvious clue) close examination may reveal that the ferrite bobbin has an extra bit glued on the end opposite the leadout wires, this will be magnetic which is easily confirmed by offering it the tip of a screwdriver. Mark the base of the bobbin as per the polarising stripe and peel off the shrink wrap to inspect the winding for heat damage. If the part is knackered it will be practically impossible to order a replacement - go down the dump and claim a monitor of similar size & spec to salvage the part from, but try it first - you may get lucky. |
Strange shrunken capacitor(?)
On Jun 12, 10:04 am, "ian field" wrote:
"w9gb" wrote in message . .. "Yattaro" wrote in message . net... I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. 1. The "white goo" appears to be hot glue use to hold the component (possibly during wave soldering step) 2. This circuit board has silk-screened legends, such as C102, L302, etc. The first character used to identify this component will tell you what it is: "C" - capacitor, "L" - inductor 3. The component appears to have a polarity stripe, like electrolytic capacitors. 4. IF this is an electrolytic capacitor -- I would replace it based upon it physical condition -- but you would need the correct value and voltage rating! From your photos, really can not tell -- no value markings other than the marking of: LO5G Its definitely an inductor - quite likely a linearity coil (polarising stripe is an obvious clue) close examination may reveal that the ferrite bobbin has an extra bit glued on the end opposite the leadout wires, this will be magnetic which is easily confirmed by offering it the tip of a screwdriver. Mark the base of the bobbin as per the polarising stripe and peel off the shrink wrap to inspect the winding for heat damage. If the part is knackered it will be practically impossible to order a replacement - go down the dump and claim a monitor of similar size & spec to salvage the part from, but try it first - you may get lucky.- Hide quoted text - - Show quoted text - From the part number, it looks like a 0.05uH ferrite-core inductor. (L05G). This should be a start, if nothing else. http://jql.manufacturer.globalsource...r-Inductor.htm Peter Wieck Wyncote, PA |
Strange shrunken capacitor(?)
wrote in message oups.com... On Jun 12, 10:04 am, "ian field" wrote: "w9gb" wrote in message . .. "Yattaro" wrote in message . net... I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it has a sort of rainbow swirl pattern in the center of the screen. I opened it up to see if there was anything obviously wrong, and saw what looks like a capacitor which has been twisted and shrunken, but I'll admit that my knowledge is limited enough that it could be something else entirely. Here are some pictures. The white goo on the side is just glue, it didn't come from inside the object. I didn't see any obvious signs of leakage or damage, but this thing certainly looks unnatural. http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v Any idea what this is, if it's bad, and if replacing it might solve the shutdown problem? Thanks for any info anyone can provide. 1. The "white goo" appears to be hot glue use to hold the component (possibly during wave soldering step) 2. This circuit board has silk-screened legends, such as C102, L302, etc. The first character used to identify this component will tell you what it is: "C" - capacitor, "L" - inductor 3. The component appears to have a polarity stripe, like electrolytic capacitors. 4. IF this is an electrolytic capacitor -- I would replace it based upon it physical condition -- but you would need the correct value and voltage rating! From your photos, really can not tell -- no value markings other than the marking of: LO5G Its definitely an inductor - quite likely a linearity coil (polarising stripe is an obvious clue) close examination may reveal that the ferrite bobbin has an extra bit glued on the end opposite the leadout wires, this will be magnetic which is easily confirmed by offering it the tip of a screwdriver. Mark the base of the bobbin as per the polarising stripe and peel off the shrink wrap to inspect the winding for heat damage. If the part is knackered it will be practically impossible to order a replacement - go down the dump and claim a monitor of similar size & spec to salvage the part from, but try it first - you may get lucky.- Hide quoted text - - Show quoted text - From the part number, it looks like a 0.05uH ferrite-core inductor. (L05G). This should be a start, if nothing else. http://jql.manufacturer.globalsource...r-Inductor.htm Peter Wieck Wyncote, PA For the value of a CRT display these days its hardly worth the effort of what I suggested, let alone what's involved ordering a one-off part from China! |
Strange shrunken capacitor(?)
w9gb wrote:
1. The "white goo" appears to be hot glue use to hold the component (possibly during wave soldering step) 2. This circuit board has silk-screened legends, such as C102, L302, etc. The first character used to identify this component will tell you what it is: "C" - capacitor, "L" - inductor 3. The component appears to have a polarity stripe, like electrolytic capacitors. The line appears to be an indicator of the position of the leads. 4. IF this is an electrolytic capacitor -- I would replace it based upon it physical condition -- but you would need the correct value and voltage rating! When was the last time you saw an electrolytic made with a molded ferrite core? From your photos, really can not tell -- no value markings other than the marking of: LO5G Which indicates that its an inductor, not a capacitor. -- Service to my country? Been there, Done that, and I've got my DD214 to prove it. Member of DAV #85. Michael A. Terrell Central Florida |
Strange shrunken capacitor(?)
"ian field" wrote in message ... Its definitely an inductor - quite likely a linearity coil (polarising stripe is an obvious clue) close examination may reveal that the ferrite bobbin has an extra bit glued on the end opposite the leadout wires, this will be magnetic which is easily confirmed by offering it the tip of a screwdriver. Could you elaborate on this type of inductors? Polarized? what does the magnet do? Thank you. Best Regards |
Strange shrunken capacitor(?)
"Steve Sousa" wrote in message anews.com... "ian field" wrote in message ... Its definitely an inductor - quite likely a linearity coil (polarising stripe is an obvious clue) close examination may reveal that the ferrite bobbin has an extra bit glued on the end opposite the leadout wires, this will be magnetic which is easily confirmed by offering it the tip of a screwdriver. Could you elaborate on this type of inductors? Polarized? what does the magnet do? Makes it easier to saturate the core with current in one direction than the other. |
Strange shrunken capacitor(?)
Steve Sousa wrote:
Could you elaborate on this type of inductors? Polarized? what does the magnet do? It prevents the core from saturating, due to the DC current flowing through the winding(s). -- Service to my country? Been there, Done that, and I've got my DD214 to prove it. Member of DAV #85. Michael A. Terrell Central Florida |
Strange shrunken capacitor(?)
On 12 jun, 04:47, Yattaro wrote:
I have an old Gateway EV700 monitor which shuts down after a few minutes of use. It sometimes sort of flashes the screen as if maybe it's trying to start back up, but is never able to on its own. It will come back on for a few seconds if power cycled, but will then shut down again. After it's been off for awhile it will come back on and last a few more minutes, but then exhibits the above problems again. When it shuts down, it you'll need to look at the pcb underside and check for cracked solder joints. especially in the power supply and line stages where larger or hotter components are. this sort of intermittent problem is often caused by poor solder. |
Strange shrunken capacitor(?)
http://tinyurl.com/2ysl3r
http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v I've never seen one of these. Open it up!!! |
Strange shrunken capacitor(?)
"Esther & Fester Bestertester" wrote in message obal.net... http://tinyurl.com/2ysl3r http://tinyurl.com/ytxby8 http://tinyurl.com/2gbe8v I've never seen one of these. Open it up!!! They're very common in monitors and power supplies. Don't mess with it, it's not your problem. |
All times are GMT +1. The time now is 04:06 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter