About TV Repair: How do I disconnect Anode connection from Circuit board?
I'm trying to disconnect CRT from main circuit board on my 27" Sony Trinston? I did disconnect all the wires except the Anode Connection wire (red color). I tried to pull out from the power source on main circuit board, not from CRT. It just did not come out. What do I have to do? Is this wire a clipped or not? |
About TV Repair: How do I disconnect Anode connection from Circuit board?
"Red Cloud" wrote in message ups.com... I'm trying to disconnect CRT from main circuit board on my 27" Sony Trinston? I did disconnect all the wires except the Anode Connection wire (red color). I tried to pull out from the power source on main circuit board, not from CRT. It just did not come out. What do I have to do? Is this wire a clipped or not? It should be a wire or pressed steel sprung clip, which fits into what is called a 'cavity connector' on the CRT bowl. For most CRTs, removal requires that the edge of the 'poppy' is gently lifted from the bowl, until you can see the actual metal contact, and then by pressing on one side of the contact, with the tip of a thin screwdriver shaft, until it bends in enough to relase on one side. The other side can then just be lifted out. BEWARE. Much lightning lingers in that cavity connector, and can do for a very long time after the TV was last powered. Do take care lest this lingering lightning smites thee ... Arfa |
About TV Repair: How do I disconnect Anode connection from Circuit board?
On Jun 8, 1:20 am, "Arfa Daily" wrote:
"Red Cloud" wrote in message ups.com... I'm trying to disconnect CRT from main circuit board on my 27" Sony Trinston? I did disconnect all the wires except the Anode Connection wire (red color). I tried to pull out from the power source on main circuit board, not from CRT. It just did not come out. What do I have to do? Is this wire a clipped or not? It should be a wire or pressed steel sprung clip, which fits into what is called a 'cavity connector' on the CRT bowl. For most CRTs, removal requires that the edge of the 'poppy' is gently lifted from the bowl, until you can see the actual metal contact, and then by pressing on one side of the contact, with the tip of a thin screwdriver shaft, until it bends in enough to relase on one side. The other side can then just be lifted out. BEWARE. Much lightning lingers in that cavity connector, and can do for a very long time after the TV was last powered. Do take care lest this lingering lightning smites thee ... Arfa Thanks for rebut this but.. I don't wanna pull it out from CRT bowl. The other side was not coming out last time I tried to lift up hard. It just did not come out. Well I tried again... |
About TV Repair: How do I disconnect Anode connection from Circuit board?
On Fri, 08 Jun 2007 22:15:25 -0700, Red Cloud
wrote: Thanks for rebut this but.. I don't wanna pull it out from CRT bowl. That's your only option. THat is the way it is meant to come out. The other side was not coming out last time I tried to lift up hard. It just did not come out. Well I tried again... You are doing something wrong... g Go back and *look* carefully at the connector at the tube. This is not rocket science, you'll figure it out. Trying to 'disconnect' at the other end will only break it. |
About TV Repair: How do I disconnect Anode connection from Circuit board?
Red Cloud wrote in news:1181366125.737552.143070
@i38g2000prf.googlegroups.com: Thanks for rebut this but.. I don't wanna pull it out from CRT bowl. The other side was not coming out last time I tried to lift up hard. It just did not come out. Well I tried again... You have to, tht is the way nearly all anod leads disconnect. |
All times are GMT +1. The time now is 04:25 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter