atx power supply
 

Hello
I would appreciate it if someone would tell me how to test an atx power
supply with digital volt meter. (how to rig the atx plug to turn on the
supply so I can check it)
Thanks a bunch,
flubber

--
Posted via a free Usenet account from http://www.teranews.com

atx power supply
 

cm wrote:
Hello
I would appreciate it if someone would tell me how to test an atx power
supply with digital volt meter. (how to rig the atx plug to turn on the
supply so I can check it)
Thanks a bunch,
flubber

--
Posted via a free Usenet account from http://www.teranews.com

I guess it depends how rigorous a test you want to do.

To do it right requires a bunch of high-power adjustable resistors.

To do it at all usually requires at least one substantial load
resistor, as most switching power supplies don't run at all with no
load.

And you do have to load down all the outputs, as a supply may be able
to put out 12 volts with no load, but not with any realistic load.

For very rough starters, get a 1 ohm 50 watt resistor and place it
across the 5 volt output, that will draw 25 watts. Or a half-ohm
resistor, that's 50 watts. Or more of these in parallel to draw
whatever wattage you want to test at.

Same for the 3.3 volt output, only there a one ohm resistor draws about
10 watts.

For the +12 output, a two ohm resistor draws about 70 watts, a one
ohmer 144 watts.

For the low-current outputs like -5 and -12, a 10 ohm resistor draws
2,.5 watts and 14.4 watts respectively.

Oh, there's also the always-on outputs, be sure to load them too.

the formula is watts = voltage squared over ohms.

or watts = current squared times ohms.

Go ahead and have fun, just don't burn yourself on the hot resistors!



pins., then ground the remote startup pin for a second, then go ahead
and measure the voltages.

atx power supply
 

Ancient_Hacker wrote:


cm wrote:
Hello
I would appreciate it if someone would tell me how to test an atx power
supply with digital volt meter. (how to rig the atx plug to turn on the
supply so I can check it)
Thanks a bunch,
flubber

--
Posted via a free Usenet account from http://www.teranews.com

I guess it depends how rigorous a test you want to do.

To do it right requires a bunch of high-power adjustable resistors.

To do it at all usually requires at least one substantial load
resistor, as most switching power supplies don't run at all with no
load.

And you do have to load down all the outputs, as a supply may be able
to put out 12 volts with no load, but not with any realistic load.

For very rough starters, get a 1 ohm 50 watt resistor and place it
across the 5 volt output, that will draw 25 watts. Or a half-ohm
resistor, that's 50 watts. Or more of these in parallel to draw
whatever wattage you want to test at.

Same for the 3.3 volt output, only there a one ohm resistor draws about
10 watts.

For the +12 output, a two ohm resistor draws about 70 watts, a one
ohmer 144 watts.

For the low-current outputs like -5 and -12, a 10 ohm resistor draws
2,.5 watts and 14.4 watts respectively.

Oh, there's also the always-on outputs, be sure to load them too.

the formula is watts = voltage squared over ohms.

or watts = current squared times ohms.

Go ahead and have fun, just don't burn yourself on the hot resistors!



pins., then ground the remote startup pin for a second, then go ahead
and measure the voltages.

Thank you, you've helped a bunch. I had forgotten about the remote
startup... thanks again

--
Posted via a free Usenet account from http://www.teranews.com

atx power supply
 

"cm" wrote in message
.. .
Hello
I would appreciate it if someone would tell me how to test an atx power
supply with digital volt meter. (how to rig the atx plug to turn on the
supply so I can check it)
Thanks a bunch,
flubber

--
Posted via a free Usenet account from http://www.teranews.com


On the atx connector theres a green wire. take a paperclip or small piece of
wire, push it into the hole of the green wire, and then to any of the black
wires. the unit will turn on. you can check the voltages, remember, yellow
wires should be +12v red +5v and I believe orange is -5v. but. to properly
test a ATX supply, you should get a ATX tester. it can test it for you. and
without any load on the ps, it will be hard to diagnose any voltage
problems. by itself the voltages might look fine but when actually under
load, they can be way off. when ti is under load it should still be within
the tolerance for + and - if it isnt then its time to replace it. if the
voltages are under while running the hardware normally, you could do damage
to it. same if they are over beyond tolerance.

ive lost a hard drive due to a faulty PS over voltage damaging the drive. so
better to be safe than sorry. maybe someone else here has alot more
experience with testing them to be able to offer other suggestions. :)

atx power supply
 

cm wrote in
:

I would appreciate it if someone would tell me how to test an atx
power supply with digital volt meter. (how to rig the atx plug to
turn on the supply so I can check it)

So you load down the outputs and turn on the ps and measure the
voltages. If one of the voltages is off, you'll know the ps is bad.
But what if all the voltages are within spec? Can you conclude that the
ps is OK? No, you can't! Because all the voltages may be OK for hours,
then one of them has a glitch. Your PC may not run well under those
conditions. And you may never see it, even if you stare at your
voltmeter for hours. Conclusion: substitute a known-good ps. (Power
supplies are cheap.) If your PC problems go away, be happy.

ATX power supply
 

"cm" wrote in message
.. .
Hello
I would appreciate it if someone would tell me how to test an atx power
supply with digital volt meter. (how to rig the atx plug to turn on the
supply so I can check it)
Thanks a bunch,
flubber

You did not happen to read thsi group's FAQ?
http://www.repairfaq.org/F_email.html

Sam Goldwasser a web page -- Troubleshooting and Repair of Small Switchmode
Power Supplies.
A little education is always useful.
Also remember that switch mode power supplies -- have high voltage ( 300
volts) inside - that is part of the design!
http://www.repairfaq.org/sam/smpsfaq.htm

gb