Audio distortion analyzer software for PC
 

I am about to start tackling some audio and FM repairs and was in the
process of finding a used distortion analyzer but was wondering if any
company produces a software program that could run through a PC to
measure distortion? I really hate to add a piece of equipment that'll
be used so infrequently if I don't have to. Any information? Thanks

Audio distortion analyzer software for PC
 

Why do you want one of these? I'm just curious.

I worked in a high-end audio repair shop for a few years, and we had
one of these. It was big, expensive, and the only real purpose I ever
saw it accomplish was to allay the fears of paranoid customers who were
afraid that their equipment had mysteriously fallen out of design
specs.

We had other tools for aligning FM RF's, IF's, detectors and such (are
such concepts dinosaurs nowadays?). AF power section bias adjustments
we performed with current measurements.

Audio distortion analyzer software for PC
 

Actually, I'm trying to follow the instructions of the manufacturer,
Marantz in this case, which specifies using a distortion meter as part
of the alignment..

Audio distortion analyzer software for PC
 

"powerdoc" wrote in message
oups.com...
I am about to start tackling some audio and FM repairs and was in the
process of finding a used distortion analyzer but was wondering if any
company produces a software program that could run through a PC to
measure distortion? I really hate to add a piece of equipment that'll
be used so infrequently if I don't have to. Any information? Thanks



I would view software distortion analyzers skeptically. First, in order to
get the sound into your computer, it has to be sampled by the sound card.
Sampling, by its nature,can't yield a 100% true representation of the
original waveform. The software has to interpolate the waveform between
samples. The higher the sample rate, the more accurate the interpolated
waveform will be, but most sound cards are limited to 44 KHz. That may be
good enough to listen to, but I would view it to be inadequate when trying
to do distortion analysis on a high frequency audio signal.
The software only has the samples of the original to do analysis on,
therefore, it can't give very accurate results over a wide range of
frequencies.

If I absolutely needed a distortion analyzer, I would shop Ebay or a hamfest
for an HP 334 or similar. Those instruments are superbly constructed, and
don't suffer from the sampling problem. You can't go wrong with one of
those.

--
Dave M
MasonDG44 at comcast dot net (Just substitute the appropriate characters in
the address)

Never take a laxative and a sleeping pill at the same time!!

Audio distortion analyzer software for PC
 

Think about what you are trying to do. For the signal to be analyzed in
software, you are going to have to acquire it and A/D convert it. I would
guess that an aquisition module that would have the resolution and bandwidth
to do so would be more expensive than buying a used analog unit, if you
could even find such a system. There are likely lots of shops going out of
business that have used audio gear like this. Then the cost of the software
or writing the code yourself...probably not too hard to do in something like
Matlab or Labview, but I'd be wary of the acquisition end .

Leonard

"powerdoc" wrote in message
oups.com...
I am about to start tackling some audio and FM repairs and was in the
process of finding a used distortion analyzer but was wondering if any
company produces a software program that could run through a PC to
measure distortion? I really hate to add a piece of equipment that'll
be used so infrequently if I don't have to. Any information? Thanks

Audio distortion analyzer software for PC
 

Thanks for replies: Somewhat validates my own ideas but was trying to
find a way to use existing hardware. HP 334 here we come

Audio distortion analyzer software for PC
 

powerdoc wrote:
I am about to start tackling some audio and FM repairs and was in the
process of finding a used distortion analyzer

What do you hope to see that you won't see on a 'scope?

Audio distortion analyzer software for PC
 

A distortion meter will measure distortion levels that would not be
discernable on a scope.

Amounts like 0.05% on a sine wave.

doing it in software. FWIW (probably nuthin' at this point), I
agree with previous posters. By the time you get a sine
wave through a PC, it's probably already got 2,3 or more % distortion
on it.

I remember the analyzer we had, it may well have been an HP. I think,
on its highest setting, it was something like 0.1% full scale, so if
you trusted the linearity of the meter you could measure down to 0.01%
At those levels, everything was very sensitive. All connectors had to
be clean and tight or you'd get erratic/false readings. You could tap
a shielded cable with your finger and make the meter jump.

Good luck!

Audio distortion analyzer software for PC
 

I'll probably be spending about $250 for a $125 alignment but I'll have
fun trying!