Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Toshiba tube shorted. Can I clear it?
I have a shorted pic tube in a Toshiba 32" 32afx61 flat screen Thompson
tube. Before I trash it how can I try to clear short? Shops want $100 bucks to try 'with no promisses' of course. Id rather put taht money towards a new tv. I know trying this is a last ditch effort. The tube is shot anyway. So I know I cant hurt it. Its only about 3 1/2 years old. I already tried to isolate heater. The short is not to the heater. The red gun is shorted I dont know the label of the other pins that are shorted. It is NOT ...blue, green, heater, or G1. The 2 other pins that are shorted to the red are connected to ground on the neck board. Looking at the tube from the back they are from about 7 oclock to 2 oclock. The RK is in the middle and the other 2 are are at each end. I tried tapping on neck. didnt help. I would like to try to burn it clear if that is the next thing to try. How can I do that? Thanks Roy |
#2
|
|||
|
|||
For starters, how about telling us the code/type of CRT. 32afx61 is
not the tube type. Then, how do you know it is shorted, which pins are shorted to which pins,etc. |
#3
|
|||
|
|||
Roy and Rosa wrote:
I have a shorted pic tube in a Toshiba 32" 32afx61 flat screen Thompson tube. Before I trash it how can I try to clear short? Shops want $100 bucks to try 'with no promisses' of course. Id rather put taht money towards a new tv. I know trying this is a last ditch effort. The tube is shot anyway. So I know I cant hurt it. Its only about 3 1/2 years old. I already tried to isolate heater. The short is not to the heater. The red gun is shorted I dont know the label of the other pins that are shorted. It is NOT ...blue, green, heater, or G1. The 2 other pins that are shorted to the red are connected to ground on the neck board. Looking at the tube from the back they are from about 7 oclock to 2 oclock. The RK is in the middle and the other 2 are are at each end. I tried tapping on neck. didnt help. I would like to try to burn it clear if that is the next thing to try. How can I do that? Thanks Roy I've had some interesting results with a stun gun. Not enough energy to melt a hard short, but can smoke a bit of debris. mike -- Return address is VALID but some sites block emails with links. Delete this sig when replying. .. Wanted, PCMCIA SCSI Card for HP m820 CDRW. FS 500MHz Tek DSOscilloscope TDS540 Make Offer Wanted 12" LCD for Compaq Armada 7770MT. Bunch of stuff For Sale and Wanted at the link below. MAKE THE OBVIOUS CHANGES TO THE LINK htremovethistp://www.geocities.com/SiliconValley/Monitor/4710/ |
#4
|
|||
|
|||
You will need the CRT rejuvenator unit, and to know how to use it.
Since you were quoted a high price in your opinion to try to rejuvenate the CRT, you should call around your area to find a service shop that would do it for a lower rate. -- JANA _____ "Roy and Rosa" wrote in message ... I have a shorted pic tube in a Toshiba 32" 32afx61 flat screen Thompson tube. Before I trash it how can I try to clear short? Shops want $100 bucks to try 'with no promisses' of course. Id rather put taht money towards a new tv. I know trying this is a last ditch effort. The tube is shot anyway. So I know I cant hurt it. Its only about 3 1/2 years old. I already tried to isolate heater. The short is not to the heater. The red gun is shorted I dont know the label of the other pins that are shorted. It is NOT ...blue, green, heater, or G1. The 2 other pins that are shorted to the red are connected to ground on the neck board. Looking at the tube from the back they are from about 7 oclock to 2 oclock. The RK is in the middle and the other 2 are are at each end. I tried tapping on neck. didnt help. I would like to try to burn it clear if that is the next thing to try. How can I do that? Thanks Roy |
#5
|
|||
|
|||
I have a shorted pic tube in a Toshiba 32" 32afx61 flat screen Thompson tube. Before I trash it how can I try to clear short? Shops want $100 bucks to try 'with no promisses' of course. Id rather put taht money towards a new tv. I know trying this is a last ditch effort. The tube is shot anyway. So I know I cant hurt it. Its only about 3 1/2 years old. I already tried to isolate heater. The short is not to the heater. The red gun is shorted I dont know the label of the other pins that are shorted. It is NOT ...blue, green, heater, or G1. The 2 other pins that are shorted to the red are connected to ground on the neck board. Looking at the tube from the back they are from about 7 oclock to 2 oclock. The RK is in the middle and the other 2 are are at each end. I tried tapping on neck. didnt help. I would like to try to burn it clear if that is the next thing to try. How can I do that? Thanks Roy I've had some success charging up a capacitor to a couple hundred volts and discharging it into the shorted pins. Start with something small, maybe 10uF and go from there. In a pinch you can charge it from rectified AC line. |
#6
|
|||
|
|||
On Wed, 17 Aug 2005 21:44:08 -0500, "Roy and Rosa"
wrote: I have a shorted pic tube in a Toshiba 32" 32afx61 flat screen Thompson tube. Before I trash it how can I try to clear short? Shops want $100 bucks to try 'with no promisses' of course. Id rather put taht money towards a new tv. I know trying this is a last ditch effort. The tube is shot anyway. So I know I cant hurt it. Its only about 3 1/2 years old. I already tried to isolate heater. The short is not to the heater. The red gun is shorted I dont know the label of the other pins that are shorted. It is NOT ...blue, green, heater, or G1. The 2 other pins that are shorted to the red are connected to ground on the neck board. Looking at the tube from the back they are from about 7 oclock to 2 oclock. The RK is in the middle and the other 2 are are at each end. I tried tapping on neck. didnt help. I would like to try to burn it clear if that is the next thing to try. How can I do that? Thanks Roy What are the other 2 pins labelled as? They may be alternates for other CRT boards? Tom |
#7
|
|||
|
|||
"Tom MacIntyre" wrote in message ... On Wed, 17 Aug 2005 21:44:08 -0500, "Roy and Rosa" wrote: I have a shorted pic tube in a Toshiba 32" 32afx61 flat screen Thompson tube. Before I trash it how can I try to clear short? Shops want $100 bucks to try 'with no promisses' of course. Id rather put taht money towards a new tv. I know trying this is a last ditch effort. The tube is shot anyway. So I know I cant hurt it. Its only about 3 1/2 years old. I already tried to isolate heater. The short is not to the heater. The red gun is shorted I dont know the label of the other pins that are shorted. It is NOT ...blue, green, heater, or G1. The 2 other pins that are shorted to the red are connected to ground on the neck board. Looking at the tube from the back they are from about 7 oclock to 2 oclock. The RK is in the middle and the other 2 are are at each end. I tried tapping on neck. didnt help. I would like to try to burn it clear if that is the next thing to try. How can I do that? Thanks Roy What are the other 2 pins labelled as? They may be alternates for other CRT boards? Tom numbers on tube The tube is Phillips tube not a thompson. Sorry bout that. A80ERF031X13 D-9223 Im doing this from memory I could have missed a pin BUT I know the shorted pins are the pins on the ends and the red K. pins are numbered from 5 to 12 clockwise (not including the pin in the 'key') none are labeled but I know what some are. 5- shorted to 8 & 12 --- this pin in connected to ground on neck board 6- green gun 7- 8- Red gun The SHORTED one 9- heater 10- heater 11- blue gun 12- shorted to 5&8 --- this pin in connected to ground on neck board I'll confirm these pins tomorrow Roy |
#8
|
|||
|
|||
On Thu, 18 Aug 2005 21:36:04 -0500, "Roy and Rosa"
put finger to keyboard and composed: Im doing this from memory I could have missed a pin BUT I know the shorted pins are the pins on the ends and the red K. pins are numbered from 5 to 12 clockwise (not including the pin in the 'key') none are labeled but I know what some are. 5- shorted to 8 & 12 --- this pin in connected to ground on neck board 6- green gun 7- 8- Red gun The SHORTED one 9- heater 10- heater 11- blue gun 12- shorted to 5&8 --- this pin in connected to ground on neck board I'll confirm these pins tomorrow Roy Where are G1 (brightness) and G2 (screen)? - Franc Zabkar -- Please remove one 's' from my address when replying by email. |
#9
|
|||
|
|||
"Franc Zabkar" wrote in message ... On Thu, 18 Aug 2005 21:36:04 -0500, "Roy and Rosa" put finger to keyboard and composed: Im doing this from memory I could have missed a pin BUT I know the shorted pins are the pins on the ends and the red K. pins are numbered from 5 to 12 clockwise (not including the pin in the 'key') none are labeled but I know what some are. 5- shorted to 8 & 12 --- this pin in connected to ground on neck board 6- green gun 7- 8- Red gun The SHORTED one 9- heater 10- heater 11- blue gun 12- shorted to 5&8 --- this pin in connected to ground on neck board I'll confirm these pins tomorrow Roy Where are G1 (brightness) and G2 (screen)? I rechecked the tube and Pins are correct as labeled. Pin 7 has 270+ volts on it. There are 2 pins in the 'key' that have wires running back to the flyback. I dont know G1 from G2 with them being labeled for me. This flyback has 3 adjustments though...screen,and what appears to be 2 focuses (focii?) I was able to clear the short to pin 8 ,the red, (charged a 150 uf cap to 200 vdc) 5 and 12 remain connected. dont know if they should be. The pics still looks pretty bad, alot of red and blue. I suppose cutoff is controlled in the service menu huh. No pots on board. This is the newest tv ive ever worked on! I'll push on slowly. Thanks for the replys, Roy |
#10
|
|||
|
|||
On Mon, 22 Aug 2005 17:53:21 -0500, "Roy and Rosa"
put finger to keyboard and composed: "Franc Zabkar" wrote in message .. . On Thu, 18 Aug 2005 21:36:04 -0500, "Roy and Rosa" put finger to keyboard and composed: Im doing this from memory I could have missed a pin BUT I know the shorted pins are the pins on the ends and the red K. pins are numbered from 5 to 12 clockwise (not including the pin in the 'key') none are labeled but I know what some are. 5- shorted to 8 & 12 --- this pin in connected to ground on neck board 6- green gun 7- 8- Red gun The SHORTED one 9- heater 10- heater 11- blue gun 12- shorted to 5&8 --- this pin in connected to ground on neck board I'll confirm these pins tomorrow Roy Where are G1 (brightness) and G2 (screen)? I rechecked the tube and Pins are correct as labeled. Pin 7 has 270+ volts on it. That looks like G1. There are 2 pins in the 'key' that have wires running back to the flyback. Probably Focus and G2/Screen. I dont know G1 from G2 with them being labeled for me. This flyback has 3 adjustments though...screen,and what appears to be 2 focuses (focii?) - Franc Zabkar -- Please remove one 's' from my address when replying by email. |
#11
|
|||
|
|||
Franc Zabkar wrote:
I rechecked the tube and Pins are correct as labeled. Pin 7 has 270+ volts on it. That looks like G1. I have never in my life seen such a high G1 voltage. It is most certainly G2. In that case the voltage is a bit low, which is either caused by the load of the voltmeter, or somehow related to your problem. There are 2 pins in the 'key' that have wires running back to the flyback. Probably Focus and G2/Screen. Wrong again, probably. These are the 2 focus connections. --- Met vriendelijke groet, Maarten Bakker. |
#12
|
|||
|
|||
|
#13
|
|||
|
|||
..
5- shorted to 8 & 12 --- this pin in connected to ground on neck board 6- green gun 7- 8- Red gun The SHORTED one 9- heater 10- heater 11- blue gun 12- shorted to 5&8 --- this pin in connected to ground on neck board I'll confirm these pins tomorrow Roy Where are G1 (brightness) and G2 (screen)? I rechecked the tube and Pins are correct as labeled. Pin 7 has 270+ volts on it. There are 2 pins in the 'key' that have wires running back to the flyback. I dont know G1 from G2 with them being labeled for me. This flyback has 3 adjustments though...screen,and what appears to be 2 focuses (focii?) I was able to clear the short to pin 8 ,the red, (charged a 150 uf cap to 200 vdc) 5 and 12 remain connected. dont know if they should be. The pics still looks pretty bad, alot of red and blue. I suppose cutoff is controlled in the service menu huh. No pots on board. This is the newest tv ive ever worked on! I'll push on slowly. Thanks for the replys, Roy picture went red again after about 5 minutes of running. I zapped it again. It shows clear when checked with an ohmmeter but goes red with retrace a few seconds after I turn it on. It must short as it heats up. pin 8 has about 100 volts on so its not a dead short. I put 3.7 volts on heater pins to simulate running and checked red cathode resistance, but no shorts. also noticed inside the neck of tube is not glowing very bright when I applied power to heaters compared to how bright it is when set is turned on. Does heat come from the guns themselves or from a short I have in tube? Also when I ground blue cathode...screen is solid blue. when I ground red cathode.... no change since screen is already red. when I ground green cathode... NO CHANGE screen still red. Is this tube screwed completely? I get no continuity between any pins except the heaters. Still messing with it. Roy (pin 7 is screen) |
#14
|
|||
|
|||
"Roy and Rosa" bravely wrote to "All" (01 Sep 05 17:31:41)
--- on the heady topic of " Toshiba tube shorted. Can I clear it?" RaR From: "Roy and Rosa" RaR Subject: Toshiba tube shorted. Can I clear it? RaR Organization: Posted via Supernews, http://www.supernews.com RaR Xref: core-easynews sci.electronics.repair:341129 |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
draining CH after Fernox Restorer - how clear is clear? | UK diy | |||
Hitachi Projection Tube Part Description Confusion | Electronics Repair | |||
Tech Review: Victor's (8liners/Genao) Replacement Arcade RGB Monitor Chassis (LONG) | Electronics Repair | |||
Need info: Brimar D7-200GH cathode ray tube | Electronics Repair | |||
Sony Trinitron lost green & a homemade CRT test jig. (kv-27ts20) | Electronics Repair |