Home audio amplifier failure
First, this is my first entry into this group. I ran a NG search for this
problem, and the result(s) indicated here. Sorry, if that was wrong. I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. Next, I'm not an electronics guy. I'm just looking for a little seasoned advice. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Comments? Thanks, for the help. Gary |
Gary wrote:
First, this is my first entry into this group. I ran a NG search for this problem, and the result(s) indicated here. Sorry, if that was wrong. I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. Next, I'm not an electronics guy. I'm just looking for a little seasoned advice. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Comments? Thanks, for the help. Gary Used amps in good condition can often be found at a small fraction of the price of new. Remember - you were happy with your (used -- by you) amp until it broke, so why not consider a good used (by somebody else) amp? There are lots of people who regularly "trade up" whether they can hear the difference or not -- it's a form of self-flattery. That puts some pretty good equipment on the market cheap. -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
"Gary" wrote in message . .. First, this is my first entry into this group. I ran a NG search for this problem, and the result(s) indicated here. Sorry, if that was wrong. I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. Next, I'm not an electronics guy. I'm just looking for a little seasoned advice. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Comments? Thanks, for the help. Gary find a repair shop and have it fixed... should cost $75 to $100 for repair |
"Gary" wrote in message . .. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Perfectly serviceable but it's your choice. I even see them in thrifts, the only problem being testing them there. N |
"CJT" wrote in message ... Gary wrote: First, this is my first entry into this group. I ran a NG search for this problem, and the result(s) indicated here. Sorry, if that was wrong. I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. Next, I'm not an electronics guy. I'm just looking for a little seasoned advice. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Comments? Thanks, for the help. Gary Used amps in good condition can often be found at a small fraction of the price of new. Remember - you were happy with your (used -- by you) amp until it broke, so why not consider a good used (by somebody else) amp? There are lots of people who regularly "trade up" whether they can hear the difference or not -- it's a form of self-flattery. That puts some pretty good equipment on the market cheap. Yes, you are quite right. And, I often criticize those for making a brand switch under the light of comparison of a bright shiny new model vs. retention of the current brand. Although I wasn't really looking specifically to change brands, I was looking at everything available. Things like this change/evolve so quickly, it's easy for me to get behind. Regarding the used/trade-in issue, I hadn't really given that any thought. It is a good suggestion. But, for some- one like me, with minimal ability to detect potential problems in electronic equipment, I'd prefer new. Also, unless possibly a high end audio outlet, I've have no idea where to find used equipment as this. I guess the pawnshop is certainly an option, but I'd think one would need considerable more savvy than me. Thanks, Gary -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
"NSM" wrote in message news:VacCe.135948$tt5.107243@edtnps90... "Gary" wrote in message . .. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Perfectly serviceable but it's your choice. I even see them in thrifts, the only problem being testing them there. N That's my take on the whole thing. But, I will take this, and the other suggestions into consideration. Problem is, I don't know an RF from a DSP, and unless I find someone I can trust, my scrutiny is suspect. Thanks, Gary |
"TimPerry" wrote in message ... "Gary" wrote in message . .. First, this is my first entry into this group. I ran a NG search for this problem, and the result(s) indicated here. Sorry, if that was wrong. I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. Next, I'm not an electronics guy. I'm just looking for a little seasoned advice. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. It's my opinion(only opinion) that replacement should be the choice, rather than a repair attempt. Comments? Thanks, for the help. Gary find a repair shop and have it fixed... should cost $75 to $100 for repair I will check into it. I do have a friend who repairs guitar amplifiers. Not that I would try to cop a free repair, just that I would trust him. But, I thought that one could easily exceed the unit value by attempting repair. Thanks, Gary |
However, I can crank up the volume to full, and faintly hear the audio Sounds like maybe the tape monitor is engaged. Maybe nothing wrong worth the amp. Even if the amp does have a problem, the A-RV401 is a nice model, worth repair. Mark Z. |
"Mark D. Zacharias" wrote in message .. . However, I can crank up the volume to full, and faintly hear the audio Sounds like maybe the tape monitor is engaged. Maybe nothing wrong worth the amp. Even if the amp does have a problem, the A-RV401 is a nice model, worth repair. Mark Z. I understand your comment, but although I have engaged all the input sources at one time or another, the faint audio can be detected as from the source intended. Yes. it has been a great unit. It was suggested earlier that repair might be worth looking into, which I will. I'd hate to just throw the whole thing away due to something small. Thanks, Gary |
"Gary Walker" wrote in message .. . "Mark D. Zacharias" wrote in message .. . However, I can crank up the volume to full, and faintly hear the audio Sounds like maybe the tape monitor is engaged. Maybe nothing wrong worth the amp. Even if the amp does have a problem, the A-RV401 is a nice model, worth repair. Mark Z. I understand your comment, but although I have engaged all the input sources at one time or another, the faint audio can be detected as from the source intended. Yes. it has been a great unit. It was suggested earlier that repair might be worth looking into, which I will. I'd hate to just throw the whole thing away due to something small. Thanks, Gary Then perhaps a failure of the regulated power supply area. You'd hear nothing at all if the main amp was blown or if there were a large DC offset. Could be one or more open resistors feeding voltage regulator(s) in the power supply. Fairly common problem on similar model Onkyo receivers, though I've only worked on one or two amps like yours, and it's been a while. Mark Z. Mark Z. |
"Mark D. Zacharias" wrote in message .. . "Gary Walker" wrote in message .. . "Mark D. Zacharias" wrote in message .. . However, I can crank up the volume to full, and faintly hear the audio Sounds like maybe the tape monitor is engaged. Maybe nothing wrong worth the amp. Even if the amp does have a problem, the A-RV401 is a nice model, worth repair. Mark Z. I understand your comment, but although I have engaged all the input sources at one time or another, the faint audio can be detected as from the source intended. Yes. it has been a great unit. It was suggested earlier that repair might be worth looking into, which I will. I'd hate to just throw the whole thing away due to something small. Thanks, Gary Then perhaps a failure of the regulated power supply area. You'd hear nothing at all if the main amp was blown or if there were a large DC offset. Could be one or more open resistors feeding voltage regulator(s) in the power supply. Fairly common problem on similar model Onkyo receivers, though I've only worked on one or two amps like yours, and it's been a while. Mark Z. Mark Z. Well, as I said, I don't really know. I can say that this amp never runs about 30% volume, I just use it mostly for headphone listening. If I juice up the volume to 100%, I'll hear the audio at about the depth I might expect at 1-5%. "The amplifier's just ain't amplifying". g I still haven't decided, intending on contact of an amp repair friend. But, I have found another equivalent replacement Onkyo for ~$300 at Fry's. It's a TX-8511. Thanks, Gary |
Mark D. Zacharias wrote:
However, I can crank up the volume to full, and faintly hear the audio Sounds like maybe the tape monitor is engaged. Maybe nothing wrong worth the amp. Even if the amp does have a problem, the A-RV401 is a nice model, worth repair. Mark Z. Just a thought, but it hasn`t got those linking plugs or jumpers between the preamp and power amps has it? have they been removed, or has some other piece of kit been disconnected? Ron -- Lune Valley Audio Public address system Hire, Sales, Repairs www.lunevalleyaudio.com |
"Ron(UK)" wrote in message ... Mark D. Zacharias wrote: However, I can crank up the volume to full, and faintly hear the audio Sounds like maybe the tape monitor is engaged. Maybe nothing wrong worth the amp. Even if the amp does have a problem, the A-RV401 is a nice model, worth repair. Mark Z. Just a thought, but it hasn`t got those linking plugs or jumpers between the preamp and power amps has it? have they been removed, or has some other piece of kit been disconnected? Ron -- Lune Valley Audio Public address system Hire, Sales, Repairs www.lunevalleyaudio.com Unfortunately, I don't fully understand "linking plugs", and never really have fully understood "preamp" vs. "power amp". But, I can say this: The system(components:tuner, amplifier, headphones) were in use the previous evening ~22:30-23:30, with- out sign of failure. This system has been used daily for 10 years. Proceeding to use the system during the subsequent day and, no audio.... I guess something could have wiggled loose, but since I can get this faint audio, and I have done a cursory "reset" of all rear panel attach- ments, I just assume it's gone. Although this system is only used for 1-2 hour periods at a time, it will sometimes remain on for 24 hour periods. Although not electronically oriented myself, I have to assume these things have a MTBF. I guess after 10 years of flawless service, my number's up. Additionally, the components are positioned in a very dusty area, and haven't been cleaned since new. Actually, it's no more dusty that any other room, but due to lack of cleaning, it appears very dusty. IOW. The whole thing is located in a music room, with other instruments and junk(need I say more?). Thanks, Gary |
On Sat, 16 Jul 2005 17:06:05 GMT "Gary" wrote:
I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. Separate units like yours are generally easier to fix than integrated units, so this helps. I don't know anything about your model, but my first inclination would be to see if it can be fixed. These items generally are fixable and for much less money than the replacement cost you mention. The fact that both channels both seem to have died at the same time makes this seem like it might be a simple problem. It might pay to get your friend over there just to check out the system and the switch settings (like the tape monitor that Mark mentioned.) I agree completely with your other posts that it would all depend on finding someone you think you can trust to take a look at it. - ----------------------------------------------- Jim Adney Madison, WI 53711 USA ----------------------------------------------- |
"Jim Adney" wrote in message ... On Sat, 16 Jul 2005 17:06:05 GMT "Gary" wrote: I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. Separate units like yours are generally easier to fix than integrated units, so this helps. I don't know anything about your model, but my first inclination would be to see if it can be fixed. These items generally are fixable and for much less money than the replacement cost you mention. The fact that both channels both seem to have died at the same time makes this seem like it might be a simple problem. It might pay to get your friend over there just to check out the system and the switch settings (like the tape monitor that Mark mentioned.) I agree completely with your other posts that it would all depend on finding someone you think you can trust to take a look at it. - ----------------------------------------------- Jim Adney Madison, WI 53711 USA ----------------------------------------------- Thanks. I am weaning off the unit for these last few days. That'll make my diagnosis more thorough. Gary |
Jim Adney wrote:
On Sat, 16 Jul 2005 17:06:05 GMT "Gary" wrote: I have an Onkyo home audio component system. The amplifier in this system(Onkyo A-RV401) has flamed out, as least I'm pretty sure it's the amplifier. The system no longer produces any sound, no tuner, tape, CD, headphones, nothing. However, I can crank up the volume to full, and faintly hear the audio. As usual, this worked fine one day, and failed the next. It appears that this component can be replaced with something like, for around $400-600. It also appears that current models have the tuner/amplifier integrated into a single unit, where the existing unit(s) are separate. Separate units like yours are generally easier to fix than integrated units, so this helps. I don't know anything about your model, but my first inclination would be to see if it can be fixed. These items generally are fixable and for much less money than the replacement cost you mention. The fact that both channels both seem to have died at the same time makes this seem like it might be a simple problem. That's a good point. It suggests some problem with a section that's common to both channels -- like a power supply. It might pay to get your friend over there just to check out the system and the switch settings (like the tape monitor that Mark mentioned.) I agree completely with your other posts that it would all depend on finding someone you think you can trust to take a look at it. - ----------------------------------------------- Jim Adney Madison, WI 53711 USA ----------------------------------------------- -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
"Gary Walker" wrote in message ... Unfortunately, I don't fully understand "linking plugs", and never really have fully understood "preamp" vs. "power amp". But, I can say this: On the back there may be some connectors labelled Out and In which need to be connected together to make the system work. Can you post a picture of the back somewhere (not in this group please)? N |
"NSM" wrote in message news:ddyCe.157817$on1.59565@clgrps13... "Gary Walker" wrote in message ... Unfortunately, I don't fully understand "linking plugs", and never really have fully understood "preamp" vs. "power amp". But, I can say this: On the back there may be some connectors labelled Out and In which need to be connected together to make the system work. Can you post a picture of the back somewhere (not in this group please)? N Well yeah, I'm aware of the component plugs on the rear. I'd just never heard them referred to as linking plugs. Come to think of it, I'd never really known their true description other than RCAplug/Miniplug etc. With regard to a picture of the rear, no I don't have one, and I have no scanner with which to record the diagram in the hardcopy I do have. However, I've managed to locate: http://onkyousa.com/own_manuals.cfm?cat=Receiver which shows the A-RV401 instruction manual. Although it doesn't seem an exact copy of the hardcopy I have, it does have some documentation. But, unlike my hardcopy, I didn't see a simple back panel schematic as is shown in my hardcopy. Perhaps, I just overlooked it. The diagnostic section occurs on pp.15. But.... I did overlook/fail to think about/stupidly ignore the diag- nostic section(aka troubleshooting) in either copy. Using the hardcopy manual, and following the procedures for "power but no sound", I see: Tape monitor on - No, but I do now recall having prob- lems with this in the past when I'd press the wrong butt- on in the dark. Pressing tape2 switches to tape2 input, but merely pressing tuner will not return to tuner, but shows T2 monitor. Another press of tape2 releases the T2 monitor, and returns the faint signal. Bad connections - Possible, but since I've reset all conn- ections, and I can get the faint audio from all sources( tuner, CD) available, this possibility seems very unlikely. Amplifier protection circuitry has been activated - I have no clue. The response here is to contact the service cen- ter. In the online troubleshooting guide, a muting button is described. My unit has no mute button, or I just can't seem to find it. It does have a standby button, and that will disable sound, but it is correctly positioned. Perhaps this standby is synonymous with muting? Although the online manual indicates that "protect" will be shown if the protective circuitry activation has occ- urred, my hardcopy manual make no mention of this. I assume I have no protect designation. I did just returned from a closer unit inspection. In the amp view window, where the input source is shown, I do see a "very" small muting word. Review of the online manual pp. 11 describes muting as activated via the remote unit. Well, although I have had the remote connected(I guess it's a remote receiver, because the remote is wireless), not only have I never used the remote, I'm not really sure even where it is. The text suggests that the only way to de-mute is via the remote, or a cycle of the amp's power. I can certainly say that a power cycle on the amp has no effect on this. Further research on this seems to indicate that the muting function is stuck on. Even after disconnecting the rc cable from the amp(one rc cable connects the tuner to the amp, and the other rc cable connects the tape to the CD), the amp continues to initialize in mute mode. It appears that this is probably the problem, but I'll be damned if I know how to correct it. Perhaps, I'll either have it looked at, or contact Onkyo for assistance(unlikely they'll bother with equipment this old). Sorry, for the verbosity.... Thanks, Gary |
"Gary Walker" wrote in message ... Further research on this seems to indicate that the muting function is stuck on. Even after disconnecting the rc cable from the amp(one rc cable connects the tuner to the amp, and the other rc cable connects the tape to the CD), the amp continues to initialize in mute mode. It appears that this is probably the problem, but I'll be damned if I know how to correct it. Perhaps, I'll either have it looked at, or contact Onkyo for assistance(unlikely they'll bother with equipment this old). That'll do it. Until you can un mute it you will have no sound. As for the linking or jumping plugs, this model probably doesn't have them but if you look at the bottom right diagram on page 4 of the A-RV401 manual on a model that _WAS_ designed this way the equalizer jacks would be permanently connected in to out, left to left and right to right with very short cables. Removing these without connecting an equalizer would also cut the sound. N |
"NSM" wrote in message news:YvBCe.158406$on1.86006@clgrps13... "Gary Walker" wrote in message ... Further research on this seems to indicate that the muting function is stuck on. Even after disconnecting the rc cable from the amp(one rc cable connects the tuner to the amp, and the other rc cable connects the tape to the CD), the amp continues to initialize in mute mode. It appears that this is probably the problem, but I'll be damned if I know how to correct it. Perhaps, I'll either have it looked at, or contact Onkyo for assistance(unlikely they'll bother with equipment this old). That'll do it. Until you can un mute it you will have no sound. As for the linking or jumping plugs, this model probably doesn't have them but if you look at the bottom right diagram on page 4 of the A-RV401 manual on a model that _WAS_ designed this way the equalizer jacks would be permanently connected in to out, left to left and right to right with very short cables. Removing these without connecting an equalizer would also cut the sound. N Thanks, I did find the remote, and will research possibly trying to use it to de-mute, but I don't hold much hope. I've also sent mail to Onkyo explaining the situation, but don't hold much hope there either. I'll post my progress as this saga unfolds. Thank you, and everyone for the assistance and contri- bution(s). BTW. That "muting" word is very very tiny, meant for eyes much younger than mine. Gary |
"Gary Walker" wrote in message .. . Thanks, I did find the remote, and will research possibly trying to use it to de-mute, but I don't hold much hope. It's possible the amp has a fault in the muting circuits. I've also sent mail to Onkyo explaining the situation, but don't hold much hope there either. I'll post my progress as this saga unfolds. Thank you, and everyone for the assistance and contri- bution(s). BTW. That "muting" word is very very tiny, meant for eyes much younger than mine. Welcome to my world. N |
"NSM" wrote in message news:M%CCe.158565$on1.2873@clgrps13... "Gary Walker" wrote in message .. . Thanks, I did find the remote, and will research possibly trying to use it to de-mute, but I don't hold much hope. It's possible the amp has a fault in the muting circuits. I've also sent mail to Onkyo explaining the situation, but don't hold much hope there either. I'll post my progress as this saga unfolds. Thank you, and everyone for the assistance and contri- bution(s). BTW. That "muting" word is very very tiny, meant for eyes much younger than mine. Welcome to my world. N I kinda' givin' thought that maybe an AC spike/outage may have caused the problem. Although all the equipment is on a strip, I can't see any other cause, unless it's faulty, as you mention. Gary |
I kinda' givin' thought that maybe an AC spike/outage may have caused the problem. Although all the equipment is on a strip, I can't see any other cause, unless it's faulty, as you mention. Gary I have a PDF service manual. If you would like it, and can take an attachment of 1.5 meg or so, you can e-mail me direct at: and reverse the domain name. Mark Z. |
Well, that's kool, I do that sometimes myself.... Yeah, it appears that the amp is in permanent mute mode. I did just speak with the amp repair friend(guitar/instru- ment amps), and he said he'd need a schematic. Over- all, it just seems like it will require extraordinary effort as opposed to a ~$300 replacement. Thanks, Gary "Ross Herbert" wrote in message ... PS. If I had read ALL of the other posts before posting myself I would have seen this point has already been covered. |
"Gary Walker" wrote in message . .. Well, that's kool, I do that sometimes myself.... Yeah, it appears that the amp is in permanent mute mode. I did just speak with the amp repair friend(guitar/instru- ment amps), and he said he'd need a schematic. Over- all, it just seems like it will require extraordinary effort as opposed to a ~$300 replacement. It may be in mute mode for a reason - perhaps solvable by reading the owner's manual? N |
Well, I have read the owner's(aka instruction manual), both in hardcopy & online. Very little is said concerning the mute specification, other than: (paraphrasing) Mute can be initiated via the rc transmitter(which I never used since the unit was new, 10 years ago). Mute can be disabled via the rc transmitter, or by offing the amp. I've pretty much proven this power cycling of the amp will not de-mute. I'll agree though, mute is probably on for a reason, it's just a matter of whether the reason is valid(reversible), or invalid(irreversible, without internal intervention). Because of its long periods of service(it gets left on 24- 36 hours sometimes), I had just been wondering how this might affect its health, and what I'd do if it failed. But, I expected an amplifier breakdown, not a false mute mode interruption. I am going to try one last thing this afternoon, as soon as I can dig up a couple of AAA bat- teries. I'll replug the rc cable, arm the remote, and see if the rc operation has any effect. But, I hold little optimism. Pending results.... Thanks, Gary "NSM" wrote in message news:0sdDe.95924$wr.26447@clgrps12... "Gary Walker" wrote in message . .. Well, that's kool, I do that sometimes myself.... Yeah, it appears that the amp is in permanent mute mode. I did just speak with the amp repair friend(guitar/instru- ment amps), and he said he'd need a schematic. Over- all, it just seems like it will require extraordinary effort as opposed to a ~$300 replacement. It may be in mute mode for a reason - perhaps solvable by reading the owner's manual? N |
I've been following this thread, and am wondering if the mute function on
this amp is different than most I've used. In every one I've owned, the mute is really a -10 to -20 dB attenuator as opposed to an absolute silencing of all audio. In fact, I usually use my daily driver in mute mode because it gives me finer control over the volume, especially given the 'stepped' nature of the remote operation. With the mute off, I don't turn the knob past 10 o'clock or so in normal operation. With the mute on, I get up to maybe 3 o'clock before distortion set in. (Of course, this mode occasionally 'bites' me when someone hits the mute button with the volume up.) jak "Gary Walker" wrote in message .. . Well, I have read the owner's(aka instruction manual), both in hardcopy & online. Very little is said concerning the mute specification, other than: (paraphrasing) Mute can be initiated via the rc transmitter(which I never used since the unit was new, 10 years ago). Mute can be disabled via the rc transmitter, or by offing the amp. I've pretty much proven this power cycling of the amp will not de-mute. I'll agree though, mute is probably on for a reason, it's just a matter of whether the reason is valid(reversible), or invalid(irreversible, without internal intervention). Because of its long periods of service(it gets left on 24- 36 hours sometimes), I had just been wondering how this might affect its health, and what I'd do if it failed. But, I expected an amplifier breakdown, not a false mute mode interruption. I am going to try one last thing this afternoon, as soon as I can dig up a couple of AAA bat- teries. I'll replug the rc cable, arm the remote, and see if the rc operation has any effect. But, I hold little optimism. Pending results.... Thanks, Gary "NSM" wrote in message news:0sdDe.95924$wr.26447@clgrps12... "Gary Walker" wrote in message . .. Well, that's kool, I do that sometimes myself.... Yeah, it appears that the amp is in permanent mute mode. I did just speak with the amp repair friend(guitar/instru- ment amps), and he said he'd need a schematic. Over- all, it just seems like it will require extraordinary effort as opposed to a ~$300 replacement. It may be in mute mode for a reason - perhaps solvable by reading the owner's manual? N |
Well, to everyone here following the saga of this thread,
the Onkyo amplifier muting problem now seems solved. Many details exist, but basically I got the rc transmitter from the original plastic bag, dug up some AA batteries, re-plugged the components rc cables, and started push- ing buttons. Not really much happened at first. Interestingly, the amp has a huge volume knob right in the middle of the front panel. Testing the rc volume +/- activates some kind of small motor that actually advances/retards the knob. g But, on to the real problem. I couldn't even find the muting button on the rc unit at first. Unlike the other buttons, it's printed in red on the black background. Being color blind I had to resort to one of those lighted magnifiers made for old people. g Pushing the mute button did easily disable the status on the amp's display. However, power cycling the amp, seems to guarantee initialization in mute mode. But, now that I can disable this, that's ok. Again, I now have the full amplificaton restored. Thanks again, to everyone that forced me to explore all possibilities. I held little optimism for this last diagnosis, but I was certainly proven wrong. Thanks, Gary |
"Gary Walker" wrote in message . .. However, power cycling the amp, seems to guarantee initialization in mute mode. But, now that I can disable this, that's ok. Again, I now have the full amplificaton restored. That's a weird one, but motorized controls are going back some. N |
Well, don't know much about attenuator etc., but the amp seems to work like this. It has an on/off button(stay with me here....). when one chooses to operate the amp via rc, only the rc on/off should be used. The amp's on/off should remain on. Next, this mute function, as I described earlier, doesn't completely eliminate all audio. But, I think that's what is intended. Like you, I hardly ever operate the amp at anywhere past the 9-10 o-clock range. However, with mute activated, the volume must be in- creased to 100% just to hear even the most faint sign of audio. Don't know, but I suspect this faint audio is what I would term bleed through/crosstalk etc. I did review attenuator meaning, and if that's the inten- tion of this amp's design, then the definition should be changed from reducing to 99.50% elimination. Thanks, Gary "jakdedert" wrote in message ... I've been following this thread, and am wondering if the mute function on this amp is different than most I've used. In every one I've owned, the mute is really a -10 to -20 dB attenuator as opposed to an absolute silencing of all audio. In fact, I usually use my daily driver in mute mode because it gives me finer control over the volume, especially given the 'stepped' nature of the remote operation. With the mute off, I don't turn the knob past 10 o'clock or so in normal operation. With the mute on, I get up to maybe 3 o'clock before distortion set in. (Of course, this mode occasionally 'bites' me when someone hits the mute button with the volume up.) jak "Gary Walker" wrote in message .. . Well, I have read the owner's(aka instruction manual), both in hardcopy & online. Very little is said concerning the mute specification, other than: (paraphrasing) Mute can be initiated via the rc transmitter(which I never used since the unit was new, 10 years ago). Mute can be disabled via the rc transmitter, or by offing the amp. I've pretty much proven this power cycling of the amp will not de-mute. I'll agree though, mute is probably on for a reason, it's just a matter of whether the reason is valid(reversible), or invalid(irreversible, without internal intervention). Because of its long periods of service(it gets left on 24- 36 hours sometimes), I had just been wondering how this might affect its health, and what I'd do if it failed. But, I expected an amplifier breakdown, not a false mute mode interruption. I am going to try one last thing this afternoon, as soon as I can dig up a couple of AAA bat- teries. I'll replug the rc cable, arm the remote, and see if the rc operation has any effect. But, I hold little optimism. Pending results.... Thanks, Gary "NSM" wrote in message news:0sdDe.95924$wr.26447@clgrps12... "Gary Walker" wrote in message . .. Well, that's kool, I do that sometimes myself.... Yeah, it appears that the amp is in permanent mute mode. I did just speak with the amp repair friend(guitar/instru- ment amps), and he said he'd need a schematic. Over- all, it just seems like it will require extraordinary effort as opposed to a ~$300 replacement. It may be in mute mode for a reason - perhaps solvable by reading the owner's manual? N |
All times are GMT +1. The time now is 02:53 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter