Digital LCD display defects ghosting
 

I have a handheld battery powered instrument with a LCD display that has a
sort-of ghosting appearance (slow transition response?).

The readings are stable, they aren't drifting or searching for a reading, as
they might if the input components were out-of-spec.

(1) The digits change slowly
(2) the display looks different when viewed at an angle for certain
readings.

When the decimal point is in one place, the digits look normal.. but when a
different range is displayed, the display looks OK viewed straight on, but
looks like it's all eights (88888) when viewed from an angle (off center
from the left side).

Is it likely that the slow transition time is a fault/result of the A-D
converter/driver IC? It's a socketed Intersil ICM 7211AIPL 40-pin device.

Would the ghosting be related to a backplane or a DP signal?

Do polarizer filters go bad? If one is utilized I suspect that it's bonded
to the LCD.

I've inspected and cleaned the zebra strips and board pads for the display
signals, and the same symptoms are still present.

Any suggestions would be appreciated

Thanks
WB



----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

"Wild Bill" wrote in message
...
I have a handheld battery powered instrument with a LCD display that has a
sort-of ghosting appearance (slow transition response?).

The readings are stable, they aren't drifting or searching for a reading,
as
they might if the input components were out-of-spec.

(1) The digits change slowly
(2) the display looks different when viewed at an angle for certain
readings.

When the decimal point is in one place, the digits look normal.. but when
a
different range is displayed, the display looks OK viewed straight on, but
looks like it's all eights (88888) when viewed from an angle (off center
from the left side).

Is it likely that the slow transition time is a fault/result of the A-D
converter/driver IC? It's a socketed Intersil ICM 7211AIPL 40-pin device.

Would the ghosting be related to a backplane or a DP signal?

Do polarizer filters go bad? If one is utilized I suspect that it's bonded
to the LCD.

I've inspected and cleaned the zebra strips and board pads for the display
signals, and the same symptoms are still present.

Any suggestions would be appreciated

Thanks
WB



----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption
=----

If you have multiplexing with numerous backplanes then it does not
take much drift in the relative voltage steps to affect the output
response as far as visibility. Suggest checking the supply to
whatever sets these multiplexed steps

Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse

Thanks Nigel, I'll see if I can locate the ADC/driver datasheet to follow
your suggestion (maybe Jameco or other supplier will have one available).

Fortunately, I have a couple of these instruments (thermocouple
calibrators), so I should be able to determine what the correct levels
should be.

Cheers
WB
.................

"N Cook" wrote in message
...

If you have multiplexing with numerous backplanes then it does not
take much drift in the relative voltage steps to affect the output
response as far as visibility. Suggest checking the supply to
whatever sets these multiplexed steps

Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse








----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----