Heat Resistant Finish for Wooden Trivet?
 

I want to make a few trivets out of wood. The last wooden one I had that
was commercially made had a shiny surface. Any tips on what kind of finish
this would be?

TIA
Norm

Heat Resistant Finish for Wooden Trivet?
 

"Norm Dresner" wrote in message
...
I want to make a few trivets out of wood. The last wooden one I had that
was commercially made had a shiny surface. Any tips on what kind of
finish
this would be?

TIA
Norm



Many "HARD" woods will sand/polish out to a shiny surface with out any
finish. Ipe for instance will polish out very nicely and actually has a
fire safety rating.

Heat Resistant Finish for Wooden Trivet?
 

On Sat, 31 Jan 2009 13:31:36 +0000, Norm Dresner wrote:

I want to make a few trivets out of wood. The last wooden one I had
that was commercially made had a shiny surface. Any tips on what kind
of finish this would be?

TIA
Norm

There are professional (read: factory use only) finishes called
conversion finishes; catalyzed lacquer. I have no experience with these
products. Two part finish, like epoxy, you mix up and have a short pot
spray life before becoming unusable.

OSHA rated breath masks are not an option, a requirement. Spray booth is
recommended.

There is a class of conversion finishes where the catalyst is included in
the can... the curing reaction starts with exposure to lots of air and is
a spray finish only. These are called pre-catalyzed lacquers, or pre-cat
lacquer. Many times sold in smaller quart containers as you would
expect. Again, normally not sold to home based shops.

Before you run off to Homestead Finishing dot com to buy some pre-cat
varnishes, take a moment and look at some trivets from neighbors and
friends. Well used ones will have marks and finish wear to show the
wooden trivets have been used. Some will even have marks of hot oven
bubbled over food from the side and bottom of a dish coming in contact
with the finish. Sort of difference between a house and a home. It
really doesn't detract. Ask the women's opinion as to their favorite
trivet and let that be your guide for effort to heat proof a wooden
trivet.

So go ahead, try some water-borne acrylic lacquer from your local store
which will be so much safer for you to apply. Not as great of heat
proofing as the expensive pre-cat stuff, but what the heck, the important
point is the trivet gets used. Wall hangings are a different subject.

Phil

Heat Resistant Finish for Wooden Trivet?
 

Phil Again wrote:
On Sat, 31 Jan 2009 13:31:36 +0000, Norm Dresner wrote:

I want to make a few trivets out of wood. The last wooden one I
had
that was commercially made had a shiny surface. Any tips on what
kind of finish this would be?

TIA
Norm

There are professional (read: factory use only) finishes called
conversion finishes; catalyzed lacquer. I have no experience with
these products. Two part finish, like epoxy, you mix up and have a
short pot spray life before becoming unusable.

OSHA rated breath masks are not an option, a requirement. Spray
booth is recommended.

Depends on the finish. For epoxies a mask will do. For polyurethanes
you need an air supplied respirator. Note that not using a mask will
not kill you if you have enough ventilation that the solvents don't
knock you down--the real danger with polyurethane is that it is a
respirator sensitizer--one day you're spraying it without a mask, the
next day being in the same building with an open can of the stuff puts
you in the ER.

There is a class of conversion finishes where the catalyst is
included in the can... the curing reaction starts with exposure to
lots of air and is a spray finish only. These are called
pre-catalyzed lacquers, or pre-cat lacquer. Many times sold in
smaller quart containers as you would expect. Again, normally not
sold to home based shops.

The ML Campbell Magnamax, a precatalyzed lacquer, actually brushes
pretty well.

Before you run off to Homestead Finishing dot com to buy some
pre-cat
varnishes, take a moment and look at some trivets from neighbors and
friends. Well used ones will have marks and finish wear to show the
wooden trivets have been used. Some will even have marks of hot oven
bubbled over food from the side and bottom of a dish coming in
contact
with the finish. Sort of difference between a house and a home. It
really doesn't detract. Ask the women's opinion as to their
favorite
trivet and let that be your guide for effort to heat proof a wooden
trivet.

So go ahead, try some water-borne acrylic lacquer from your local
store which will be so much safer for you to apply. Not as great of
heat proofing as the expensive pre-cat stuff, but what the heck, the
important point is the trivet gets used. Wall hangings are a
different subject.

Phil

--
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)

Heat Resistant Finish for Wooden Trivet?
 

On Sat, 31 Jan 2009 13:31:36 GMT, "Norm Dresner"
wrote:

I want to make a few trivets out of wood. The last wooden one I had that
was commercially made had a shiny surface. Any tips on what kind of finish
this would be?

TIA
Norm


All the wooden trivets I've made had no finish at all. They were made
to scorch, to burn, and to use. Sanding very smooth with a beeswax
finish should give a low luster. Lacquer, varnish, and urethane
finishes are very shiny, not sure what these would do if scorched,
though.

Heat Resistant Finish for Wooden Trivet?
 

In article ,
says...
All the wooden trivets I've made had no finish at all. They were made
to scorch, to burn, and to use. Sanding very smooth with a beeswax
finish should give a low luster.


I've used olive oil with a bit of gum/vegetable turps added for better
penetration, applied 2-4 times. Not particularly shiny, doesn't prevent
scorchmarks from a red-hot pan, but it works and is wet-wipable after
food splashes. Our trivets are made from Blue Gum and they certainly do
look *used* :-) but neither scored nor scorched.

-P.

Heat Resistant Finish for Wooden Trivet?
 

Norm Dresner wrote:
I want to make a few trivets out of wood. The last wooden one I had that
was commercially made had a shiny surface. Any tips on what kind of finish
this would be?

I've got one made with oak, with a BLO finish. It seems to be holding
up so far, but I don't put any *really* hot stuff on it--only up to
boiling or so.

Chris