A DIY & home improvement forum. DIYbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » DIYbanter forum » Do - it - Yourself » Woodworking
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Table saw bearings



 
 
LinkBack Thread Tools Display Modes
  #1  
Old March 22nd 08, 05:43 PM posted to rec.woodworking
external usenet poster
 
Posts: 19
Default Table saw bearings

i want to replace my worn out arbor bearings in my older craftsman table saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard


Ads
  #2  
Old March 22nd 08, 06:36 PM posted to rec.woodworking
external usenet poster
 
Posts: 1,370
Default Table saw bearings

Howard Kowall wrote:
i want to replace my worn out arbor bearings in my older craftsman table saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard



It looks like 202-10 may be the standard bearing number. See:

http://www.abtbearing.com/docs/mount...ndard-duty.pdf

--
Jack Novak
Buffalo, NY - USA

  #3  
Old March 22nd 08, 06:44 PM posted to rec.woodworking
external usenet poster
 
Posts: 4,207
Default Table saw bearings

Howard Kowall wrote:
i want to replace my worn out arbor bearings in my older craftsman
table saw i got the 2 bearings out but they are made by a company
called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much


Have you plugged the Sears parts database to see if they have
replacements in stock?

If they don't, then take what you have to any decent bearing supply
house and they should be able to match them.

--
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)


  #4  
Old March 22nd 08, 07:22 PM posted to rec.woodworking
external usenet poster
 
Posts: 1,619
Default Table saw bearings


"Howard Kowall" wrote in message
news:3zbFj.106547$w94.16750@pd7urf2no...
i want to replace my worn out arbor bearings in my older craftsman table
saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard


Go to a bearing supply house and hand them the bearings. They will hand
back to you a new set identical to what you have now. Bearings are a
universal type of part. Easy to replace. Not so easy to get them out and
replace them sometimes.



  #5  
Old March 22nd 08, 08:08 PM posted to rec.woodworking
external usenet poster
 
Posts: 19
Default Table saw bearings

yup will do thanx all for thoses who replyed
was a good chance to clean and relube all the parts underneath
thanx again
howard

"Howard Kowall" wrote in message
news:3zbFj.106547$w94.16750@pd7urf2no...
i want to replace my worn out arbor bearings in my older craftsman table
saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard




  #6  
Old March 22nd 08, 08:24 PM posted to rec.woodworking
external usenet poster
 
Posts: 2,047
Default Table saw bearings

"Howard Kowall" wrote:

i want to replace my worn out arbor bearings in my older craftsman table
saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much


You have a 40's vintage saw.

Hoover has been gone for years.

202 is a standard bearing size; however, check with Sears.

When that saw was built, 202 was the most popular size bearing built.

Today, it is the 203.

I had to do this rebuild once and Sears had an update conversion to use the
203 bearings which today are the standard size replacing the 202 from the
late 40's.

SFWIW, there are more 203 bearings made than all the other sizes combined.

Why?

203 is the standard for all fractional HP electric motors, automotive
alternators, automotive transmissions, as well as a host of other
applications.

Have fun.

Lew





  #7  
Old March 23rd 08, 07:44 AM posted to rec.woodworking
external usenet poster
 
Posts: 2,047
Default Table saw bearings-Update

If S/R still offers a bearing kit, it will be a modified water pump bearing,
at least that is what they gave me when I did this job.

You get both bearings, and arbor shaft as one ass'y.

Makes life easy.

Lew


  #8  
Old March 23rd 08, 01:50 PM posted to rec.woodworking
external usenet poster
 
Posts: 19
Default Table saw bearings

well here we go
there does not seem to be a model # on this saw
all it says is do not install more then 3/4 hp motor
seems kinda weird that a 3/4hp on this size of table saw
built like a tank
it has a cast iron top and 2 ext wings that are made from white metal
the wings are solid not web,but do have some ribs in them,it also has a
yellow disk in the front of the saw table top , the fence has 2 (1 on each
end) angle iron syle with a rod at the end of the fence system held to the
angle irion buy a rod with speed nuts on it
i have looked on the internet for a model # but always came up short
any info would be great
thanx again
howard

"Howard Kowall" wrote in message
news:ZGdFj.107818$w94.62345@pd7urf2no...
yup will do thanx all for thoses who replyed
was a good chance to clean and relube all the parts underneath
thanx again
howard

"Howard Kowall" wrote in message
news:3zbFj.106547$w94.16750@pd7urf2no...
i want to replace my worn out arbor bearings in my older craftsman table
saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard






  #9  
Old March 23rd 08, 02:04 PM posted to rec.woodworking
external usenet poster
 
Posts: 19
Default Table saw bearings

i did see a date on the table top bottom says 2-24-76

"Howard Kowall" wrote in message
news:IetFj.109366$pM4.81248@pd7urf1no...
well here we go
there does not seem to be a model # on this saw
all it says is do not install more then 3/4 hp motor
seems kinda weird that a 3/4hp on this size of table saw
built like a tank
it has a cast iron top and 2 ext wings that are made from white metal
the wings are solid not web,but do have some ribs in them,it also has a
yellow disk in the front of the saw table top , the fence has 2 (1 on each
end) angle iron syle with a rod at the end of the fence system held to the
angle irion buy a rod with speed nuts on it
i have looked on the internet for a model # but always came up short
any info would be great
thanx again
howard

"Howard Kowall" wrote in message
news:ZGdFj.107818$w94.62345@pd7urf2no...
yup will do thanx all for thoses who replyed
was a good chance to clean and relube all the parts underneath
thanx again
howard

"Howard Kowall" wrote in message
news:3zbFj.106547$w94.16750@pd7urf2no...
i want to replace my worn out arbor bearings in my older craftsman table
saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard








  #10  
Old March 24th 08, 03:50 AM posted to rec.woodworking
external usenet poster
 
Posts: 14
Default Table saw bearings

Hoover is now NSK. The 202 is the current standard 6202 bearing (metric OD
and metric width), however the number -10 following the bearing number
indicate the ID in sixteenths of an inch, which would translate to 5/8 inch
bore, which is a typical size for Craftsman equipment. They typically used
metal shields on their bearings for grease retention. I would advise getting
the new ones with the rubber seals (usually designated with a 2RS or an LL
after the bearing number), so what you would want to get is a set of 6202-10
LL, or 6202-10 2RS bearings. The difference in price between shielded and
sealed bearings is miniscule for small bearings like this. They do a much
better job of keeping sawdust out of the bearings.

When you install them, make sure you are pressing them on properly. To press
them onto a shaft, press ONLY on the inside race. If installing them into a
housing, press ONLY on the outside race. If you press on the wrong race, you
will damage the bearing and will have to replace it again soon.

If you have to drift the bearing onto the shaft or into the housing, use a
tube of some type that fits closely to the size of the race that you are
drifting. If you use a metal tube, such as a piece of pipe, DO NOT USE A
METAL HAMMER. The bearing races are hardened steel, and you can fracture the
metal. Use a dead blow hammer or piece of wood to drift them on.

"Howard Kowall" wrote in message
news:3zbFj.106547$w94.16750@pd7urf2no...
i want to replace my worn out arbor bearings in my older craftsman table
saw
i got the 2 bearings out but they are made by a company called Hoover
who are no longer in Bussness
the number on the bearing is Hoover 202-10
has anyone rever repalced them and found a cross for them
thanx very much
howard




 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Lubricant for handwheel / table bearings Louis Ohland Metalworking 3 July 30th 07 07:44 AM
ball bearings spec table Martin H. Eastburn Metalworking 1 March 5th 06 06:13 AM
ball bearings spec table Tom Gardner Metalworking 2 March 5th 06 04:55 AM
ball bearings spec table Tom Metalworking 0 March 5th 06 12:19 AM
What is proper proceedure to reinstall arbor and new bearings into jet table saw? Alan W Woodworking 2 September 30th 03 01:49 AM


All times are GMT +1. The time now is 06:31 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.SEO by vBSEO ©2010, Crawlability, Inc.
Copyright 2004-2014 DIYbanter.
The comments are property of their posters.