Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Kent P. Iler
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Hi,

I'm a beginning wood worker. I've built basic things many years ago, and
built a pretty big jungle gym/swing set in our backyard, but nothing
requiring the accuracy/joints that this will require. However, I do have a
decent selection of power tools and have decided to tackle a new project.

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints? The jig I'm planning on buying will do sliding
dovetails, mortise and tenons, dovetails, half-blind dovetails, and
supposedly over 100 more. I did order a few books on joinery, but I don't
have them yet. Obviously the jig just helps, but I need to know what to do
in order for the jig to be successful. I'm not buying it in hopes that it
will automagically make the joints for me. I will be reading up on what
joints work best for this type of project, but I'm hoping to get a head
start and recommendations for the experience folks here.

I'd like to build this so that it could be strong enough to be passed to my
children for their kids, or at least hold up for many many years. I'm tired
of the pressed board kits from Wal-mart that fall apart when you move them,
or even after 3 years if you don't move them.

Anyway, I'm planning on using a harder wood than pine for most of this, but
I need to balance strength and price - I'm not going with Walnut or Oak. I
was thinking Maple. Any recommendations as to wood would be appreciated,
too.

For now, we're going to finish this in white, as it will match the crib and
other furniture in the room. However, if it's ever refinished, it would be
nice to keep staining as an option.

FYI, the plans were purchased on a large sheet, and I put them into a
document that I could print and work with so I don't mess up the original.
You'll notice the folds in some of the pictures/graphics on the plans.

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address


  #2   Report Post  
Preston Andreas
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

If you go to www.finewoodworking.com , you can search a 600 article database
for "Chest of Drawers", and there is an excellent article on "Building a
Chest of Drawers, Joinery and Design Considerations", by Christian
Beksvoort. It is an excellent article that can be purchased for a few
dollars. Also, in issue 163, June 2003, there is a good article on
"Engineering a Chest of Drawers". This will answer a lot of your questions.

I also have an excellent book, "Illustrated Cabinetmaking, How to Design and
Construct Furniture that Works", by Bill Hylton. It gives exploded views on
traditional construction of many types of furniture, including the joinery.
When I want to see how a piece of furniture (from highboys to roll-top
desks) should be constructed, I go to this book. It doesn't give explicit
details or dimensions, but there is enough information to design and
construct your own piece. There are also sections on joinery and
subassemblies such as door and drawer construction, casework and post and
rail construction.

Essentially, you have a chest of drawers with one door. The above should
give you plenty of ideas. There are so many ways to put together such a
piece, it would be hard to give you specific advice. For myself, I would
probably dovetail the sides of the carcase to the top and bottom and apply
some sort of bracket feet. I would use sliding dovetails for the drawer
dividers and dados for the dust panels. For the drawers, I would do
half-blind dovetails in the front and through dovetails in the back of the
drawer.

Good Luck,

Preston
"Kent P. Iler" wrote in message
news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit

the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would

be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints?

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address




  #3   Report Post  
Bob Bowles
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Check library for Tage Frid Teaches Woodworkung as it has a number of
joints and how they're made. Poplar is easy to work and accepts paint
well. Most woods wont accept stain once the pores have been sealed
with finish.

On Sun, 27 Jul 2003 20:34:32 GMT, "Kent P. Iler"
wrote:

I did order a few books on joinery, but I don't
have them yet.


  #4   Report Post  
Kent P. Iler
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Thx for the advice!

--Kent

"Bob Bowles" wrote in message
...
Check library for Tage Frid Teaches Woodworkung as it has a number of
joints and how they're made. Poplar is easy to work and accepts paint
well. Most woods wont accept stain once the pores have been sealed
with finish.

On Sun, 27 Jul 2003 20:34:32 GMT, "Kent P. Iler"
wrote:

I did order a few books on joinery, but I don't
have them yet.




  #5   Report Post  
Kent P. Iler
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Thx!

--Kent

"Preston Andreas" wrote in message
. ..
If you go to www.finewoodworking.com , you can search a 600 article

database
for "Chest of Drawers", and there is an excellent article on "Building a
Chest of Drawers, Joinery and Design Considerations", by Christian
Beksvoort. It is an excellent article that can be purchased for a few
dollars. Also, in issue 163, June 2003, there is a good article on
"Engineering a Chest of Drawers". This will answer a lot of your

questions.

I also have an excellent book, "Illustrated Cabinetmaking, How to Design

and
Construct Furniture that Works", by Bill Hylton. It gives exploded views

on
traditional construction of many types of furniture, including the

joinery.
When I want to see how a piece of furniture (from highboys to roll-top
desks) should be constructed, I go to this book. It doesn't give explicit
details or dimensions, but there is enough information to design and
construct your own piece. There are also sections on joinery and
subassemblies such as door and drawer construction, casework and post and
rail construction.

Essentially, you have a chest of drawers with one door. The above should
give you plenty of ideas. There are so many ways to put together such a
piece, it would be hard to give you specific advice. For myself, I would
probably dovetail the sides of the carcase to the top and bottom and apply
some sort of bracket feet. I would use sliding dovetails for the drawer
dividers and dados for the dust panels. For the drawers, I would do
half-blind dovetails in the front and through dovetails in the back of the
drawer.

Good Luck,

Preston
"Kent P. Iler" wrote in message
news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by

then.
When I got the plans, I was shocked to see that they don't have any

joints
for the dresser. They just plan on nailing and gluing most ends

together,
including the drawers! There is a rabbet on the back of board A to fit

the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for

any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the

other
joints), and use that for the drawers. However, I don't know what would

be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints?

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address








  #6   Report Post  
Bill Wallace
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Kent,

You should learn about pocket screws. You can get a small gig for
$20-$30 dollars. They are very strong and will allow you to cut the
wood exactly as the plans show. They should work in most locations.

Three considerations:

First, place them where they will be hidden although they can be
plugged with purchased wood dowels shaped appropriately but its no
fun.

Secondly, be careful in planning, you need room to get the screw gun
in and in some spaces it might be too small and hand driving them is
difficult. Sometimes, just the order of assembly can solve that
problem.

Finally, always clamp the joints firmly in place befor driving the
screws. The low cost fixtures make a 15 degreee pocket and the screws
tend to want to lift the joining piece.

"Kent P. Iler" wrote in message news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I'm a beginning wood worker. I've built basic things many years ago, and
built a pretty big jungle gym/swing set in our backyard, but nothing
requiring the accuracy/joints that this will require. However, I do have a
decent selection of power tools and have decided to tackle a new project.

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints? The jig I'm planning on buying will do sliding
dovetails, mortise and tenons, dovetails, half-blind dovetails, and
supposedly over 100 more. I did order a few books on joinery, but I don't
have them yet. Obviously the jig just helps, but I need to know what to do
in order for the jig to be successful. I'm not buying it in hopes that it
will automagically make the joints for me. I will be reading up on what
joints work best for this type of project, but I'm hoping to get a head
start and recommendations for the experience folks here.

I'd like to build this so that it could be strong enough to be passed to my
children for their kids, or at least hold up for many many years. I'm tired
of the pressed board kits from Wal-mart that fall apart when you move them,
or even after 3 years if you don't move them.

Anyway, I'm planning on using a harder wood than pine for most of this, but
I need to balance strength and price - I'm not going with Walnut or Oak. I
was thinking Maple. Any recommendations as to wood would be appreciated,
too.

For now, we're going to finish this in white, as it will match the crib and
other furniture in the room. However, if it's ever refinished, it would be
nice to keep staining as an option.

FYI, the plans were purchased on a large sheet, and I put them into a
document that I could print and work with so I don't mess up the original.
You'll notice the folds in some of the pictures/graphics on the plans.

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address

  #7   Report Post  
Kent P. Iler
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Are the pocket screws as strong as other joints that you'd typically
use? I guess I'm thinking that the screws will loosen sooner than a
strong joint will.

--Kent

(Bill Wallace) wrote in message . com...
Kent,

You should learn about pocket screws. You can get a small gig for
$20-$30 dollars. They are very strong and will allow you to cut the
wood exactly as the plans show. They should work in most locations.

Three considerations:

First, place them where they will be hidden although they can be
plugged with purchased wood dowels shaped appropriately but its no
fun.

Secondly, be careful in planning, you need room to get the screw gun
in and in some spaces it might be too small and hand driving them is
difficult. Sometimes, just the order of assembly can solve that
problem.

Finally, always clamp the joints firmly in place befor driving the
screws. The low cost fixtures make a 15 degreee pocket and the screws
tend to want to lift the joining piece.

"Kent P. Iler" wrote in message news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I'm a beginning wood worker. I've built basic things many years ago, and
built a pretty big jungle gym/swing set in our backyard, but nothing
requiring the accuracy/joints that this will require. However, I do have a
decent selection of power tools and have decided to tackle a new project.

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints? The jig I'm planning on buying will do sliding
dovetails, mortise and tenons, dovetails, half-blind dovetails, and
supposedly over 100 more. I did order a few books on joinery, but I don't
have them yet. Obviously the jig just helps, but I need to know what to do
in order for the jig to be successful. I'm not buying it in hopes that it
will automagically make the joints for me. I will be reading up on what
joints work best for this type of project, but I'm hoping to get a head
start and recommendations for the experience folks here.

I'd like to build this so that it could be strong enough to be passed to my
children for their kids, or at least hold up for many many years. I'm tired
of the pressed board kits from Wal-mart that fall apart when you move them,
or even after 3 years if you don't move them.

Anyway, I'm planning on using a harder wood than pine for most of this, but
I need to balance strength and price - I'm not going with Walnut or Oak. I
was thinking Maple. Any recommendations as to wood would be appreciated,
too.

For now, we're going to finish this in white, as it will match the crib and
other furniture in the room. However, if it's ever refinished, it would be
nice to keep staining as an option.

FYI, the plans were purchased on a large sheet, and I put them into a
document that I could print and work with so I don't mess up the original.
You'll notice the folds in some of the pictures/graphics on the plans.

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address

  #8   Report Post  
Rodger Podlogar
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!


"Kent P. Iler" wrote in message
om...
Are the pocket screws as strong as other joints that you'd typically
use? I guess I'm thinking that the screws will loosen sooner than a
strong joint will.

--Kent


Kreg claims that pocket screw joinery is stronger than mortise and tenons,
(that's their claim, not mine). From my experience I've never had a pocket
screw loosen up on me. Brush on a little glue on the joint, screw it down
and glue a plug into the hole. That screw is not going anywhere..


  #9   Report Post  
Kent P. Iler
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Any recommendations for jigs?

--Kent

(Bill Wallace) wrote in message . com...
Good question. In my experience, if you are putting two pocket screws
and some glue, this joint will never come un-done or loosen.

A few points:
Pocket screws come in two thread patterns coarse for soft woods and
fine for harder woods. This is partly because of another feature, they
are self threading and the coarse screws will break trying to drive
into Oak, etc. So you only drill the pocket and the screw itself
drills a into the joined piece. Finally, they are driven in with a
square head socket drive, usually supplied with the purchase of the
fixture. These allow for very good drilling grip. I've broken screws
when I forgot to set my drill gun to the slip setting.

You can drill these in with an electric drill but a screw gun with a
strong slip clutch set to the highest tourqe is the best so you don't
spin or break the screw.

Pretty much all face frame kitchen cabinets are built with pocket
screws now and they ain't fallin apart anytime soon.


(Kent P. Iler) wrote in message . com...
Are the pocket screws as strong as other joints that you'd typically
use? I guess I'm thinking that the screws will loosen sooner than a
strong joint will.

--Kent

(Bill Wallace) wrote in message . com...
Kent,

You should learn about pocket screws. You can get a small gig for
$20-$30 dollars. They are very strong and will allow you to cut the
wood exactly as the plans show. They should work in most locations.

Three considerations:

First, place them where they will be hidden although they can be
plugged with purchased wood dowels shaped appropriately but its no
fun.

Secondly, be careful in planning, you need room to get the screw gun
in and in some spaces it might be too small and hand driving them is
difficult. Sometimes, just the order of assembly can solve that
problem.

Finally, always clamp the joints firmly in place befor driving the
screws. The low cost fixtures make a 15 degreee pocket and the screws
tend to want to lift the joining piece.

"Kent P. Iler" wrote in message news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I'm a beginning wood worker. I've built basic things many years ago, and
built a pretty big jungle gym/swing set in our backyard, but nothing
requiring the accuracy/joints that this will require. However, I do have a
decent selection of power tools and have decided to tackle a new project.

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints? The jig I'm planning on buying will do sliding
dovetails, mortise and tenons, dovetails, half-blind dovetails, and
supposedly over 100 more. I did order a few books on joinery, but I don't
have them yet. Obviously the jig just helps, but I need to know what to do
in order for the jig to be successful. I'm not buying it in hopes that it
will automagically make the joints for me. I will be reading up on what
joints work best for this type of project, but I'm hoping to get a head
start and recommendations for the experience folks here.

I'd like to build this so that it could be strong enough to be passed to my
children for their kids, or at least hold up for many many years. I'm tired
of the pressed board kits from Wal-mart that fall apart when you move them,
or even after 3 years if you don't move them.

Anyway, I'm planning on using a harder wood than pine for most of this, but
I need to balance strength and price - I'm not going with Walnut or Oak. I
was thinking Maple. Any recommendations as to wood would be appreciated,
too.

For now, we're going to finish this in white, as it will match the crib and
other furniture in the room. However, if it's ever refinished, it would be
nice to keep staining as an option.

FYI, the plans were purchased on a large sheet, and I put them into a
document that I could print and work with so I don't mess up the original.
You'll notice the folds in some of the pictures/graphics on the plans.

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address

  #10   Report Post  
Bill Wallace
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Well, I did say $20-$30...

The cheapest I could find was indeed $30 at Rockler

http://www.rockler.com/ecom7/showdet... catid=7&DID=6

The more expensive fixtures have a toggle clamp but they are more like
$60-$90 but do come with more screws, etc. The link I posted above
comes with a jig and the drill bit and the stop collar so even though
you have to clamp it with your own clamp it has everything you need.

Just search on "pocket" at either Woodcraft or Rockler and you'll see
all kinds of fixtures and even production machines. I can't wait until
our new Castell two motor unit gets installed at my shop. ;^)


(Kent P. Iler) wrote in message . com...
Any recommendations for jigs?

--Kent

(Bill Wallace) wrote in message . com...
Good question. In my experience, if you are putting two pocket screws
and some glue, this joint will never come un-done or loosen.

A few points:
Pocket screws come in two thread patterns coarse for soft woods and
fine for harder woods. This is partly because of another feature, they
are self threading and the coarse screws will break trying to drive
into Oak, etc. So you only drill the pocket and the screw itself
drills a into the joined piece. Finally, they are driven in with a
square head socket drive, usually supplied with the purchase of the
fixture. These allow for very good drilling grip. I've broken screws
when I forgot to set my drill gun to the slip setting.

You can drill these in with an electric drill but a screw gun with a
strong slip clutch set to the highest tourqe is the best so you don't
spin or break the screw.

Pretty much all face frame kitchen cabinets are built with pocket
screws now and they ain't fallin apart anytime soon.


(Kent P. Iler) wrote in message . com...
Are the pocket screws as strong as other joints that you'd typically
use? I guess I'm thinking that the screws will loosen sooner than a
strong joint will.

--Kent

(Bill Wallace) wrote in message . com...
Kent,

You should learn about pocket screws. You can get a small gig for
$20-$30 dollars. They are very strong and will allow you to cut the
wood exactly as the plans show. They should work in most locations.

Three considerations:

First, place them where they will be hidden although they can be
plugged with purchased wood dowels shaped appropriately but its no
fun.

Secondly, be careful in planning, you need room to get the screw gun
in and in some spaces it might be too small and hand driving them is
difficult. Sometimes, just the order of assembly can solve that
problem.

Finally, always clamp the joints firmly in place befor driving the
screws. The low cost fixtures make a 15 degreee pocket and the screws
tend to want to lift the joining piece.

"Kent P. Iler" wrote in message news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I'm a beginning wood worker. I've built basic things many years ago, and
built a pretty big jungle gym/swing set in our backyard, but nothing
requiring the accuracy/joints that this will require. However, I do have a
decent selection of power tools and have decided to tackle a new project.

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints? The jig I'm planning on buying will do sliding
dovetails, mortise and tenons, dovetails, half-blind dovetails, and
supposedly over 100 more. I did order a few books on joinery, but I don't
have them yet. Obviously the jig just helps, but I need to know what to do
in order for the jig to be successful. I'm not buying it in hopes that it
will automagically make the joints for me. I will be reading up on what
joints work best for this type of project, but I'm hoping to get a head
start and recommendations for the experience folks here.

I'd like to build this so that it could be strong enough to be passed to my
children for their kids, or at least hold up for many many years. I'm tired
of the pressed board kits from Wal-mart that fall apart when you move them,
or even after 3 years if you don't move them.

Anyway, I'm planning on using a harder wood than pine for most of this, but
I need to balance strength and price - I'm not going with Walnut or Oak. I
was thinking Maple. Any recommendations as to wood would be appreciated,
too.

For now, we're going to finish this in white, as it will match the crib and
other furniture in the room. However, if it's ever refinished, it would be
nice to keep staining as an option.

FYI, the plans were purchased on a large sheet, and I put them into a
document that I could print and work with so I don't mess up the original.
You'll notice the folds in some of the pictures/graphics on the plans.

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address



  #11   Report Post  
Kent P. Iler
 
Posts: n/a
Default Please help recommend joints for dresser/armoire plans!

Thx!

--Kent

(Bill Wallace) wrote in message . com...
Well, I did say $20-$30...

The cheapest I could find was indeed $30 at Rockler

http://www.rockler.com/ecom7/showdet... catid=7&DID=6

The more expensive fixtures have a toggle clamp but they are more like
$60-$90 but do come with more screws, etc. The link I posted above
comes with a jig and the drill bit and the stop collar so even though
you have to clamp it with your own clamp it has everything you need.

Just search on "pocket" at either Woodcraft or Rockler and you'll see
all kinds of fixtures and even production machines. I can't wait until
our new Castell two motor unit gets installed at my shop. ;^)


(Kent P. Iler) wrote in message . com...
Any recommendations for jigs?

--Kent

(Bill Wallace) wrote in message . com...
Good question. In my experience, if you are putting two pocket screws
and some glue, this joint will never come un-done or loosen.

A few points:
Pocket screws come in two thread patterns coarse for soft woods and
fine for harder woods. This is partly because of another feature, they
are self threading and the coarse screws will break trying to drive
into Oak, etc. So you only drill the pocket and the screw itself
drills a into the joined piece. Finally, they are driven in with a
square head socket drive, usually supplied with the purchase of the
fixture. These allow for very good drilling grip. I've broken screws
when I forgot to set my drill gun to the slip setting.

You can drill these in with an electric drill but a screw gun with a
strong slip clutch set to the highest tourqe is the best so you don't
spin or break the screw.

Pretty much all face frame kitchen cabinets are built with pocket
screws now and they ain't fallin apart anytime soon.


(Kent P. Iler) wrote in message . com...
Are the pocket screws as strong as other joints that you'd typically
use? I guess I'm thinking that the screws will loosen sooner than a
strong joint will.

--Kent

(Bill Wallace) wrote in message . com...
Kent,

You should learn about pocket screws. You can get a small gig for
$20-$30 dollars. They are very strong and will allow you to cut the
wood exactly as the plans show. They should work in most locations.

Three considerations:

First, place them where they will be hidden although they can be
plugged with purchased wood dowels shaped appropriately but its no
fun.

Secondly, be careful in planning, you need room to get the screw gun
in and in some spaces it might be too small and hand driving them is
difficult. Sometimes, just the order of assembly can solve that
problem.

Finally, always clamp the joints firmly in place befor driving the
screws. The low cost fixtures make a 15 degreee pocket and the screws
tend to want to lift the joining piece.

"Kent P. Iler" wrote in message news:sHWUa.142123$GL4.35974@rwcrnsc53...
Hi,

I'm a beginning wood worker. I've built basic things many years ago, and
built a pretty big jungle gym/swing set in our backyard, but nothing
requiring the accuracy/joints that this will require. However, I do have a
decent selection of power tools and have decided to tackle a new project.

I purchased a set of plans for a piece that my wife liked the looks of.
We're expecting in mid-October, and I would like to get this done by then.
When I got the plans, I was shocked to see that they don't have any joints
for the dresser. They just plan on nailing and gluing most ends together,
including the drawers! There is a rabbet on the back of board A to fit the
back of the dresser, but that is it.

For those of you that would just like to look at the plans and make
recommendations without reading further, the plans are he
http://www.iler.com/plans/dresser-armoire.pdf. Thanks in advance for any
help that you can offer.

Here's a little more info if you care to read:

I'd like to get a jig for my router that will do dovetails (and the other
joints), and use that for the drawers. However, I don't know what would be
best for the rest of the joints. Can someone look at these plans and
recommend proper joints? The jig I'm planning on buying will do sliding
dovetails, mortise and tenons, dovetails, half-blind dovetails, and
supposedly over 100 more. I did order a few books on joinery, but I don't
have them yet. Obviously the jig just helps, but I need to know what to do
in order for the jig to be successful. I'm not buying it in hopes that it
will automagically make the joints for me. I will be reading up on what
joints work best for this type of project, but I'm hoping to get a head
start and recommendations for the experience folks here.

I'd like to build this so that it could be strong enough to be passed to my
children for their kids, or at least hold up for many many years. I'm tired
of the pressed board kits from Wal-mart that fall apart when you move them,
or even after 3 years if you don't move them.

Anyway, I'm planning on using a harder wood than pine for most of this, but
I need to balance strength and price - I'm not going with Walnut or Oak. I
was thinking Maple. Any recommendations as to wood would be appreciated,
too.

For now, we're going to finish this in white, as it will match the crib and
other furniture in the room. However, if it's ever refinished, it would be
nice to keep staining as an option.

FYI, the plans were purchased on a large sheet, and I put them into a
document that I could print and work with so I don't mess up the original.
You'll notice the folds in some of the pictures/graphics on the plans.

Thank you for your time!

-- Kent Iler
----------------------------------------------------------------------

Please CC: all replies via e-mail
Remove .NOSPAM from e-mail address

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Garage Plans? Homer UK diy 1 May 6th 04 04:03 PM
Soldering close joints mike ring UK diy 2 August 30th 03 07:18 PM
WTD plans for a PIG Roaster amc Metalworking 11 August 7th 03 12:15 PM
Wedding Ring Box Plans? George Woodworking 8 July 20th 03 03:26 PM
Paving Stone Joints chris French UK diy 0 July 14th 03 09:32 AM


All times are GMT +1. The time now is 12:08 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"