Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to rec.woodworking
Andy Jeffries
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?


Hi all,

I'm making a new workshop (8'x10' shed) in a few weeks and I'm going to be
making some small cabinets (3' x 3') with a worktop on top. I'm going to
be using 2x4's for the frame of the worktop then either plywood or MDF for
the top.

For the cabinets I was going to be using 18mm plywood (think Norm's Garage
Workshop, Mitre bench and Storage or Workshop Hutch projects).

However, I'm on a tight budget for the work and am wondering whether 18mm
MDF would hold up as well. The cabinets will be built and screwed to the
wall at the back and left so racking won't be an issue.

I know MDF is heavier than plywood but it's also 50% of the price (here in
the UK).

Can anyone give me a quick "should be fine for the sizes you're looking
at" or "it'll fold under it's own weight"?

I guess you'll need to see a diagram explaining the construction to give a
proper answer, but they'll be constructed the same as the last two New
Yankee Workshop projects listed above if that helps.

Cheers,


--
Andy Jeffries | gPHPEdit Lead Developer
http://www.gphpedit.org | PHP editor for Gnome 2
http://www.andyjeffries.co.uk | Personal site and photos

  #2   Report Post  
Posted to rec.woodworking
tom
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

Should be fine for the sizes you're looking at. Tom

  #3   Report Post  
Posted to rec.woodworking
Pop
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

Actually, MDF should be OK. Keep in mind it's brittle compared
to ply, so use fender washers/whatever if there's a straight pull
on it. MDF also does not like moisture/humidity and especially
water. MDF paints well too.

HTH,

Pop

"Andy Jeffries" wrote in message
news :
: Hi all,
:
: I'm making a new workshop (8'x10' shed) in a few weeks and I'm
going to be
: making some small cabinets (3' x 3') with a worktop on top.
I'm going to
: be using 2x4's for the frame of the worktop then either plywood
or MDF for
: the top.
:
: For the cabinets I was going to be using 18mm plywood (think
Norm's Garage
: Workshop, Mitre bench and Storage or Workshop Hutch projects).
:
: However, I'm on a tight budget for the work and am wondering
whether 18mm
: MDF would hold up as well. The cabinets will be built and
screwed to the
: wall at the back and left so racking won't be an issue.
:
: I know MDF is heavier than plywood but it's also 50% of the
price (here in
: the UK).
:
: Can anyone give me a quick "should be fine for the sizes you're
looking
: at" or "it'll fold under it's own weight"?
:
: I guess you'll need to see a diagram explaining the
construction to give a
: proper answer, but they'll be constructed the same as the last
two New
: Yankee Workshop projects listed above if that helps.
:
: Cheers,
:
:
: --
: Andy Jeffries | gPHPEdit Lead Developer
: http://www.gphpedit.org | PHP editor for Gnome 2
: http://www.andyjeffries.co.uk | Personal site and photos
:


  #4   Report Post  
Posted to rec.woodworking
Andy Jeffries
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

On Thu, 19 Jan 2006 07:23:58 -0800, tom wrote:
Should be fine for the sizes you're looking at. Tom


Fantastic, thanks Tom.

Cheers,


Andy


--
Andy Jeffries | gPHPEdit Lead Developer
http://www.gphpedit.org | PHP editor for Gnome 2
http://www.andyjeffries.co.uk | Personal site and photos

  #5   Report Post  
Posted to rec.woodworking
Andy Jeffries
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

On Thu, 19 Jan 2006 15:35:46 +0000, Pop wrote:
Actually, MDF should be OK. Keep in mind it's brittle compared to ply, so
use fender washers/whatever if there's a straight pull on it.


Cool. Was planning on using washers on the handles anyway. The doors
will be hung by 35mm european hinges (which may be better in MDF than
normal butt hinges anyway, due to screwing in the sides).

MDF also
does not like moisture/humidity and especially water.


Yep, not planning on using water in there (and top work surface will be
covered with replacable hardboard anyway).

MDF paints well too.


That'll be the wife's job :-) I'm construction, she's decorating (even in
my workshop).

Thanks for the nod though Pop.

Cheers,


--
Andy Jeffries | gPHPEdit Lead Developer
http://www.gphpedit.org | PHP editor for Gnome 2
http://www.andyjeffries.co.uk | Personal site and photos



  #6   Report Post  
Posted to rec.woodworking
Andy
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

Yep, as long as it's not structural and won't get soaked with water,
MDF is fine. Washers are a good idea under screws.
My basement shop is about 8'x10' right now, so I know storage and work
space are both at a premium. My walls are lined with hanging tools,
and both my "stationary" power tools (bandsaw and drill press) are on
lock-able wheels so they can snug up against walls when not in use.
The only thing I wish were different right now is to have space on the
right end of my workbench for crosscutting. Apparently the previous
owner was left-handed or clueless.
Anyway, enjoy your new shop,
Andy

  #7   Report Post  
Posted to rec.woodworking
Mike Berger
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

They use mdf for kitchen and bathroom cabinets. Since you'll have a
frame, the mdf should be fine.

Andy Jeffries wrote:

For the cabinets I was going to be using 18mm plywood (think Norm's Garage
Workshop, Mitre bench and Storage or Workshop Hutch projects).

However, I'm on a tight budget for the work and am wondering whether 18mm
MDF would hold up as well. The cabinets will be built and screwed to the
wall at the back and left so racking won't be an issue.

  #8   Report Post  
Posted to rec.woodworking
Andy Jeffries
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

On Thu, 19 Jan 2006 13:35:17 -0600, Mike Berger wrote:
They use mdf for kitchen and bathroom cabinets. Since you'll have a
frame, the mdf should be fine.


Y'know, I didn't think of that before, but you're right, very common in
kitchen cabinet construction.

Thanks for that...

Cheers,


Andy

--
Andy Jeffries | gPHPEdit Lead Developer
http://www.gphpedit.org | PHP editor for Gnome 2
http://www.andyjeffries.co.uk | Personal site and photos

  #9   Report Post  
Posted to rec.woodworking
Andy Jeffries
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

On Thu, 19 Jan 2006 10:16:40 -0800, Andy wrote:
My basement shop is about
8'x10' right now, so I know storage and work space are both at a premium.


I've been trying to convice SWMBO to go for the 8x12 shed, but it's an
extra couple of hundred pounds which is a push too far on the budget we've
got available...

My walls are lined with hanging tools, and both my "stationary" power
tools (bandsaw and drill press) are on lock-able wheels so they can snug
up against walls when not in use. The only thing I wish were different
right now is to have space on the right end of my workbench for
crosscutting. Apparently the previous owner was left-handed or clueless.


ROTFLMAO!!!

Fortunately I'll have space on the right end of my worktop/bench to go the
full length.

Anyway, enjoy your new shop,


Thanks mate.

Cheers,


Andy

--
Andy Jeffries | gPHPEdit Lead Developer
http://www.gphpedit.org | PHP editor for Gnome 2
http://www.andyjeffries.co.uk | Personal site and photos

  #10   Report Post  
Posted to rec.woodworking
entfillet
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

At a width of 36" the MDF will sag substantially under its own weight.
If it can be fastened to a surface that will keep it from sagging, it
will be fine. I am not familiar with your application but it sounds
like the top can be fastened to the underside of the top of the bench
and the bottom will have to be blocked up or have a base that can keep
the MDF from sagging. If you use MDF shelves at this width, it would
be best to incorporate at least a built up front edging, with either a
rabbet to receive the shelf, or perhaps a bisuited connection between
the edging and the shelf material, and provide a point of support at
midspan along the back edge of the shelf.



  #11   Report Post  
Posted to rec.woodworking
Woodchuck34
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

I built all of my shop cabinets out of MDF and a lot of the painted
built-ins in the house. You could just butt joint or dado them
together, but I recently started using FWW's method which essentially
amounts to a tongue and groove type of construction. My most recent
projects were a 36" high, 20" deep, and 1-54" wide, 1-52" wide MDF
cabinets. The FWW method works extremely well. One thing I started
doing is using a full 3/4" (or I suppose 18MM) thick sheet of MDF as
the backboard of the cabinet and always including at least 1 fixed
shelf (either vertically or horizontally) and securely attaching that
to the backboard. Yields a rock solid cabinet. I don't use any screws
either.

  #12   Report Post  
Posted to rec.woodworking
Andy Jeffries
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

On Fri, 20 Jan 2006 07:48:34 -0800, Woodchuck34 wrote:
I built all of my shop cabinets out of MDF and a lot of the painted
built-ins in the house. You could just butt joint or dado them together,


They'll be constructed using Norm's method of cut out strips screwed to
the edges. Difficult to explain, maybe I'll take some photos when I do it
(with the weather it looks like it'll be delayed for a week - gonna be
snowing when the guy was going to be doing the concrete base for me).

One thing I started doing is using a full
3/4" (or I suppose 18MM) thick sheet of MDF as the backboard of the
cabinet and always including at least 1 fixed shelf (either vertically or
horizontally) and securely attaching that to the backboard. Yields a rock
solid cabinet. I don't use any screws either.


Interesting. They'll actually be screwed to the back wall, but I'll see
how strong they are. The left side will be screwed to the left wall and I
can always screw a batten to the right side (and back wall) to keep them
from exploding in the middle if they look like they may.

The fixed shelf (yes mine will have one too) will be in a dado and
toe-nailed.

Cheers,


Andy


--
Andy Jeffries | gPHPEdit Lead Developer
http://www.gphpedit.org | PHP editor for Gnome 2
http://www.andyjeffries.co.uk | Personal site and photos

  #13   Report Post  
Posted to rec.woodworking
Sailaway
 
Posts: n/a
Default Workshop cabinets out of MDF instead of Plywood?

entfillet composed a while back:
At a width of 36" the MDF will sag substantially under its own weight.
If it can be fastened to a surface that will keep it from sagging, it
will be fine. I am not familiar with your application but it sounds
like the top can be fastened to the underside of the top of the bench
and the bottom will have to be blocked up or have a base that can keep
the MDF from sagging. If you use MDF shelves at this width, it would
be best to incorporate at least a built up front edging, with either a
rabbet to receive the shelf, or perhaps a bisuited connection between
the edging and the shelf material, and provide a point of support at
midspan along the back edge of the shelf.


Just reading some of the older posts, and thought I'd give my $.02 here
from my (very limited) experience in case anyone is doubtful about the
relative strength/sag-resistance of MDF. I built a U-shaped
receptionist's desk for my office out of 3/4 MDF that was just under 8
feet wide, 30 inches deep at the front, and about 6 feet back alongside
the walls/and 22" deep. I reinforced the desk along the bottom at the
edges with 2&1/2 inch wide strips of MDF, glued and nailed with a nail
gun. On top and on the edges I glued on laminate. Only the ends of the 6
foot sections were supported by under-the-counter cabinets, and the rest
of the desk was supported only along the walls by sitting on top of a
1x4 screwed flat around the wall like a cheap French Cleat without the
bevels. That desk did not warp or sag at all in the 5 years I used it,
and only very slightly at the edge under my weight when walking on it
while running wiring in the ceiling. Sag in MDF is, in my experience,
from either poor design, improper finishing allowing moisture, or some
combination of those. So using a little care, it can be a good material
for a workbench or cabinets, even in a shed or garage, that will hold up
for years.
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Cabinets in basement...melamine, mdf, plywood? RobW Woodworking 21 October 31st 06 05:55 AM
Attaching plywood to plywood for ceramic tile? Gord Home Repair 9 January 3rd 06 05:25 PM
Windsor Plywood Scam - Saskatoon James \(Garry\) Hunter Woodworking 19 January 4th 05 05:12 PM
How to hang cabinets on a curved wall? Ken Miller Woodworking 1 August 21st 04 09:52 PM
Cabinets, Let the buyer beware Clifford Keele Home Repair 18 June 25th 03 05:40 PM


All times are GMT +1. The time now is 01:11 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"