Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
noonenparticular
 
Posts: n/a
Default heavy-duty levelers

Anybody have a source for heavy duty leveling feet?

The application is to level my currently in-progress workbench. It will be
a beast (of the design favored by Frank Klausz in The Workbench Book) except
mine will have fully loaded drawers beneath. So it will be *heavy*. I
found a couple of small sources, wondering if you guys know of any.

TIA,

Joe C.


  #2   Report Post  
no(SPAM)vasys
 
Posts: n/a
Default

noonenparticular wrote:
Anybody have a source for heavy duty leveling feet?

The application is to level my currently in-progress workbench. It will be
a beast (of the design favored by Frank Klausz in The Workbench Book) except
mine will have fully loaded drawers beneath. So it will be *heavy*. I
found a couple of small sources, wondering if you guys know of any.

TIA,

Joe C.



Grainger.

http://www.grainger.com/Grainger/pro...761243&ccitem=

--
Jack Novak
Buffalo, NY - USA

(Remove -SPAM- to send email)
  #3   Report Post  
noonenparticular
 
Posts: n/a
Default

That would do it, thanks for the recommendation.

jlc

"no(SPAM)vasys" wrote in message
...
noonenparticular wrote:
Anybody have a source for heavy duty leveling feet?

The application is to level my currently in-progress workbench. It will
be a beast (of the design favored by Frank Klausz in The Workbench Book)
except mine will have fully loaded drawers beneath. So it will be
*heavy*. I found a couple of small sources, wondering if you guys know
of any.

TIA,

Joe C.



Grainger.

http://www.grainger.com/Grainger/pro...761243&ccitem=

--
Jack Novak
Buffalo, NY - USA

(Remove -SPAM- to send email)



  #4   Report Post  
 
Posts: n/a
Default

On Thu, 29 Sep 2005 21:11:26 GMT, "noonenparticular"
wrote:

Anybody have a source for heavy duty leveling feet?

The application is to level my currently in-progress workbench. It will be
a beast (of the design favored by Frank Klausz in The Workbench Book) except
mine will have fully loaded drawers beneath. So it will be *heavy*. I
found a couple of small sources, wondering if you guys know of any.

TIA,

Joe C.



the closest hardware store.

get 4 beefy lag bolts, say 5/8 x 12. bore up from the bottom of the
leg and run them in so that an inch or so of the head sticks out. tune
the bench to level with a wrench.
  #5   Report Post  
charlie b
 
Posts: n/a
Default

noonenparticular wrote:

Anybody have a source for heavy duty leveling feet?

The application is to level my currently in-progress workbench. It will be
a beast (of the design favored by Frank Klausz in The Workbench Book) except
mine will have fully loaded drawers beneath. So it will be *heavy*. I
found a couple of small sources, wondering if you guys know of any.

TIA,

Joe C.


I skipped the tail vise and went with a Twin Screw.
http://home.comcast.net/~charliebcz/...CBbench33.html
and it's heavy. Unless you like laying on the floor with two wrenches
you should try the levelers adjustable from above with an allen
wrench. Glued some 80 grit to the bottom so the bench can't slide
around on my epoxy coated cement floor.

Cal-Fasteners - photo is close to life size - beefy suckers.

bottom half of this page
http://home.comcast.net/~charliebcz/MT/CBbench20.htm

post pics of your bench when you can please.

charlie b


  #6   Report Post  
Tom Banes
 
Posts: n/a
Default

On Thu, 29 Sep 2005 16:47:15 -0700, charlie b
wrote:


I skipped the tail vise and went with a Twin Screw.
http://home.comcast.net/~charliebcz/...CBbench33.html
and it's heavy.


WOW!

Admitted screw-ups be damned, that is a piece of work!

Beautifully done.

Regards.
  #7   Report Post  
Mark Jerde
 
Posts: n/a
Default

charlie b wrote:
Cal-Fasteners - photo is close to life size - beefy suckers.

bottom half of this page
http://home.comcast.net/~charliebcz/MT/CBbench20.htm


Aw, what the 'l ;-)

http://home.comcast.net/~charliebcz/MT/CBbench20.html

-- Mark


  #8   Report Post  
 
Posts: n/a
Default

Wow Charlie.... I was interested in the leveling devices as I am going
to build my new large bowl lathe stand soon....

Then I forgot all about it when I saw your bench. What a masterpiece!
Not only is it functional and well thought out, but it is gorgeous.
Really nice work, sir.

Robert

  #9   Report Post  
charlie b
 
Posts: n/a
Default

/ Robertwrote:

Wow Charlie.... I was interested in the leveling devices as I am going
to build my new large bowl lathe stand soon....


That I'd bolt to the floor. But if you've got enough mass then these
levelers, with the 80 grit sandpaper on the bottom, should get
things level and keep it there.

Then I forgot all about it when I saw your bench. What a masterpiece!
Not only is it functional and well thought out, but it is gorgeous.
Really nice work, sir.


Thanks. You did note that it was a year of elapsed time
from start to finish? Was intimdated in handcutting
BIG through dovetails on the apron stock - stuff that
thick, that wide and that long is hard to come by,
at least for me. Fortunately I know an arborist/
sawyer/woodworker who had what I needed but not
much more if I screwed up. Was also, uneccessarily,
concerned about the Twin Screw installation - again,
the jaw stock was hard to come by and there wasn't
going to be a second chance.

I'd not do the accessible from both sides of the bench
drawers with the guides on the drawer sides. Other
than opening and closing them from the back to
show off I don't work on that side of the bench so
that "seems like a great idea" wasn't. The top
shallow drawers, suggested by Michael Baglio,
was a great idea and does keep digging down inside
them to a minimum.

If I can break a complicated piece down into low
risk modules/parts I'm less intimidated by the
project. It also lets you evolve the thing as you
go rather than commit totally to EVERYTHING
right from the get go. Using traditional joinery
really lends itself to this approach as it allows
you to dry fit what you've got and make subsequent
parts/modules/steps fit the actual space it is
to occupy. I stumbled on this approach early on
while making a pair of wall hanging tool cabinets

http://home.comcast.net/~charliebcz/...olCabinet.html

Each step along the way seemed pretty easy, with
plenty of opporotunities to try new things - at
low risk once the cabinet and the doors were done.
When it was all done and filled I did the "Did I
make that?".

By the yard it's hard. But by the inch - it's a
cinch.

charlie b
  #10   Report Post  
Joe Brophy
 
Posts: n/a
Default

On Thu, 29 Sep 2005 21:11:26 GMT, "noonenparticular" =
wrote:

Anybody have a source for heavy duty leveling feet?

The application is to level my currently in-progress workbench. It will=

be=20
a beast (of the design favored by Frank Klausz in The Workbench Book) =

except=20
mine will have fully loaded drawers beneath. So it will be *heavy*. I=20
found a couple of small sources, wondering if you guys know of any.

TIA,

Joe C.


Like these?
http://cgi.ebay.com/4-Large-Machine-...2-13-NEW_W0QQ=
itemZ7549612191QQcategoryZ633QQssPageNameZWDVWQQrd Z1QQcmdZViewItem
Joe Brophy
CountryTech Computer
email:
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
FS: Steady Rest - For heavy duty 16" lathe Jess Metalworking 1 September 26th 05 04:49 AM
Heavy Duty Toilet Seat? r.p.mcmurphy UK diy 6 January 10th 05 07:29 PM
Recommendations for plunge router and heavy duty corded drill? [email protected] Home Repair 5 December 22nd 04 08:15 PM
DeWalt DW730 Heavy Duty Miter Saw Workstation for Sale Mark Hames Woodworking 0 September 9th 04 09:21 PM
Heavy duty cleaning question ted Home Ownership 2 December 23rd 03 01:42 PM


All times are GMT +1. The time now is 02:51 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"