UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Bedouin
 
Posts: n/a
Default Best thin insulation

What's the best thin insulation available?

I need to find thin insulation (5-6mm) suitable for sticking (using
waterproof glue) to a gently curved surface. This is in a situation
where energy is in very short supply so every little improvement helps.
I expected to be able to find PUR/PIR closed cell foam in roll form
but no luck.
  #2   Report Post  
The Natural Philosopher
 
Posts: n/a
Default

Bedouin wrote:

What's the best thin insulation available?

I need to find thin insulation (5-6mm) suitable for sticking (using
waterproof glue) to a gently curved surface. This is in a situation
where energy is in very short supply so every little improvement helps.
I expected to be able to find PUR/PIR closed cell foam in roll form but
no luck.


Ah. If you key in 'depron' on an ebay sarch, someone is selling depron
sheet (expanded polyproplyene) in small quantites. 3mm and 5mm thick.
Use water based contact adhesive (copydex?)

Polystryene sheet is also available, at builders mercahnts, as are cork
sheet and bubble wrap, Mock not, these all work.

you can strip standard EPS foam with a hot wire or indeed a wood saw if
you don't mind a bit of mess.


  #3   Report Post  
Lobster
 
Posts: n/a
Default

Bedouin wrote:
What's the best thin insulation available?


I was trying to spec some thin insulation recently and a structural
engineer mentioned something called "Tri-Iso Super 9", about which I
know nothing other than it's pretty expensive, so I didn't go any
further - others here may know something about it?

David
  #4   Report Post  
Christian McArdle
 
Posts: n/a
Default

I need to find thin insulation (5-6mm) suitable for sticking (using
waterproof glue) to a gently curved surface. This is in a situation
where energy is in very short supply so every little improvement helps.
I expected to be able to find PUR/PIR closed cell foam in roll form
but no luck.


You can get celotex down to 12mm. I take it this is still too thick?

Christian


  #5   Report Post  
fred
 
Posts: n/a
Default

In article , Lobster
writes
Bedouin wrote:
What's the best thin insulation available?


I was trying to spec some thin insulation recently and a structural
engineer mentioned something called "Tri-Iso Super 9", about which I
know nothing other than it's pretty expensive, so I didn't go any
further - others here may know something about it?


It's ****, avoid.

Sorry, to elaborate:
It relies on being fitted precisely in the middle of two 1" closed air pockets
in order to work; it is thin material but not an insulating medium for use in
limited spaces. It works mainly by limiting heat transfer by radiation but
then claims to "seal roofs against wind and damp, whilst retaining
ventilation" without mentioning that where the outer pocket is ventilated the
product will perform less effectively since heat will be lost by convection
instead of radiation.

Maybe have a read between the lines in the brochu
http://www.kensaengineering.com/pdf/79.pdf (209k pdf)

IMO, avoid foil based insulation systems, other types (foam based, celotex
etc) are more likely to achieve the claimed insulation performance over the
life of the property.
--
fred


  #6   Report Post  
nog
 
Posts: n/a
Default

On Mon, 14 Mar 2005 09:32:42 GMT, fred wrote:

IMO, avoid foil based insulation systems, other types (foam based, celotex
etc) are more likely to achieve the claimed insulation performance over the
life of the property.


Wouldn't a foil component (IOW not relying totally on the foil) improve the
effectiveness of a thin insulating medium?
  #7   Report Post  
fred
 
Posts: n/a
Default

In article , nog
writes
On Mon, 14 Mar 2005 09:32:42 GMT, fred wrote:

IMO, avoid foil based insulation systems, other types (foam based, celotex
etc) are more likely to achieve the claimed insulation performance over the
life of the property.


Wouldn't a foil component (IOW not relying totally on the foil) improve the
effectiveness of a thin insulating medium?


'Fraid not, certainly not if in contact with other materials. Foil is an effective
vapour barrier but achieves heat blocking by inhibiting radiation only. If it is
in contact with any material (insulator or otherwise) the heat loss is by
conduction and not radiation so there is no benefit.
--
fred
  #8   Report Post  
nog
 
Posts: n/a
Default

On Mon, 14 Mar 2005 10:42:34 GMT, fred wrote:

In article , nog
writes
On Mon, 14 Mar 2005 09:32:42 GMT, fred wrote:

IMO, avoid foil based insulation systems, other types (foam based, celotex
etc) are more likely to achieve the claimed insulation performance over the
life of the property.


Wouldn't a foil component (IOW not relying totally on the foil) improve the
effectiveness of a thin insulating medium?


'Fraid not, certainly not if in contact with other materials. Foil is an effective
vapour barrier but achieves heat blocking by inhibiting radiation only. If it is
in contact with any material (insulator or otherwise) the heat loss is by
conduction and not radiation so there is no benefit.


Ah yes, I see your point. Thanks.
  #9   Report Post  
rockdoctor
 
Posts: n/a
Default

Lobster wrote in message ...
Bedouin wrote:
What's the best thin insulation available?


I was trying to spec some thin insulation recently and a structural
engineer mentioned something called "Tri-Iso Super 9", about which I
know nothing other than it's pretty expensive, so I didn't go any
further - others here may know something about it?

David



My mate converted his loft, and wanted to preserve the view of the
original beams on the ceiling. To avoid filling the gaps completely he
had to use the Tri-iso Super 9 stuff. Seems to have worked - the loft
is toasty and the beams look good. He said the stuff was pricey but
glad he paid.
  #10   Report Post  
Mike
 
Posts: n/a
Default


"Bedouin" wrote in message
k...
What's the best thin insulation available?

I need to find thin insulation (5-6mm) suitable for sticking (using
waterproof glue) to a gently curved surface. This is in a situation
where energy is in very short supply so every little improvement helps.
I expected to be able to find PUR/PIR closed cell foam in roll form
but no luck.


Couldn't you spray it with foam then sand down to the required shape ?




  #11   Report Post  
 
Posts: n/a
Default


Bedouin wrote:
What's the best thin insulation available?

I need to find thin insulation (5-6mm) suitable for sticking (using
waterproof glue) to a gently curved surface. This is in a situation
where energy is in very short supply so every little improvement

helps.
I expected to be able to find PUR/PIR closed cell foam in roll form


but no luck.


This is primarily for conductive insulation at 'common' temperatures?
For space heating rather than keeping an individual warm?

I have no idea of its U-value or whether its more gimmick than benefit,
but Wickes have 'foil coated' bubble wrap type stuff in rolls for
putting behind rads, under floors, dry lining, etc.

How about flooring underlays?

IanC

  #13   Report Post  
Andy Wade
 
Posts: n/a
Default

The Natural Philosopher wrote:

Even 3mm of foam is a heck of a sight better than 9" of brick.


Wrong. Thermal resistance (R-value) is thickness divided by the thermal
conductivity of the material: R = t/k.

- for 3mm foam: t = 0.003m, k = 0.03 W/mK typically,
hence R = 0.1 m^2K/W approx.

- for 9 in. brick: t = 0.225 m, k ~ 1 W/mK,
hence R = 0.2 m^2K/W approx.

So 9 in. of brick is about twice as good as 3mm of foam, so far as
steady state heat loss is concerned.

--
Andy
  #14   Report Post  
Mike
 
Posts: n/a
Default


"Steve Firth" wrote in message
.. .
Bedouin wrote:

What's the best thin insulation available?


Compressed Dr Evil, it's so dense it allows nothing through, not even a
clue.

Back when I laid the underfloor heating in the kitchen, my wife sourced
some extremely thin insulation (about 3-5mm) that claimed to be as good
as 50mm polystyrene. I'll see if I can find the sample and get the
details off it.

In the meantime someone else may recognise the stuff, it has two smooth
sheets of grey plastic (may be polyethylene or polypropylene) with a
foam sandwich.


The one I got has silver foil each side of the plastic. Called Airtec from
Screwfix and was b****y useless.


--
"They that can give up essential liberty to obtain a little
temporary safety deserve neither liberty nor safety."

-- Benjamin Franklin, 1759



  #15   Report Post  
The Natural Philosopher
 
Posts: n/a
Default

Andy Wade wrote:

The Natural Philosopher wrote:

Even 3mm of foam is a heck of a sight better than 9" of brick.



Wrong. Thermal resistance (R-value) is thickness divided by the thermal
conductivity of the material: R = t/k.

- for 3mm foam: t = 0.003m, k = 0.03 W/mK typically,
hence R = 0.1 m^2K/W approx.

- for 9 in. brick: t = 0.225 m, k ~ 1 W/mK,
hence R = 0.2 m^2K/W approx.

So 9 in. of brick is about twice as good as 3mm of foam, so far as
steady state heat loss is concerned.


Umm. let's rephrase that rather sloppy sentence.

"Even 3mm of foam on 9" of solid brick is better than no foam at all"

The remark was prompted by the fact that lining just such a wall with
3mm cork tiles - and in fact it may actually have been 4.5" brick - made
a HUGE difference.


  #16   Report Post  
The Natural Philosopher
 
Posts: n/a
Default

Steve Firth wrote:

Bedouin wrote:


What's the best thin insulation available?



Compressed Dr Evil, it's so dense it allows nothing through, not even a
clue.

Back when I laid the underfloor heating in the kitchen, my wife sourced
some extremely thin insulation (about 3-5mm) that claimed to be as good
as 50mm polystyrene. I'll see if I can find the sample and get the
details off it.


The very best insulator is polyisocyanurate board. Its precisely twice
as good as polystyrene and costs about 4 times as much. Its sold as celotex.


In the meantime someone else may recognise the stuff, it has two smooth
sheets of grey plastic (may be polyethylene or polypropylene) with a
foam sandwich.

Its called a load of old ********.
  #17   Report Post  
Mike
 
Posts: n/a
Default


"The Natural Philosopher" wrote in message
...
The very best insulator is polyisocyanurate board. Its precisely twice
as good as polystyrene and costs about 4 times as much.


Not quite. The best insulator is a vacuum. It's just nobody has found a
way of encasing a building in it yet, though I'm sure Doctor Dickhead/IMM
will detail some place where it's been done.


  #18   Report Post  
The Natural Philosopher
 
Posts: n/a
Default

Mike wrote:

"The Natural Philosopher" wrote in message
...

The very best insulator is polyisocyanurate board. Its precisely twice
as good as polystyrene and costs about 4 times as much.



Not quite. The best insulator is a vacuum. It's just nobody has found a
way of encasing a building in it yet, though I'm sure Doctor Dickhead/IMM
will detail some place where it's been done.


Ok the best COMERCIALLY AVAILABLE insulation material...ok?
  #19   Report Post  
Owain
 
Posts: n/a
Default

Steve Firth wrote:
The Natural Philosopher wrote:
Not quite. The best insulator is a vacuum. It's just nobody has found a
way of encasing a building in it yet, though I'm sure Doctor Dickhead/IMM
will detail some place where it's been done.

Ok the best COMERCIALLY AVAILABLE insulation material...ok?

Umm no, you can buy a vacuum as an insulator commercially. Thermos.


Ah yes, how to build a gerbil house that complies with Part L in 2020

Owain


  #20   Report Post  
Mike
 
Posts: n/a
Default


"Owain" wrote in message
...
Steve Firth wrote:
The Natural Philosopher wrote:
Not quite. The best insulator is a vacuum. It's just nobody has found

a
way of encasing a building in it yet, though I'm sure Doctor

Dickhead/IMM
will detail some place where it's been done.
Ok the best COMERCIALLY AVAILABLE insulation material...ok?

Umm no, you can buy a vacuum as an insulator commercially. Thermos.


Ah yes, how to build a gerbil house that complies with Part L in 2020



If Two Jags stays in charge with his ideas on high ensity housing gerbil
houses is exactly what we'll be living in as well.


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Idea for crawl INSULATION falling down aaa Home Repair 12 July 16th 04 10:36 PM
Is it possible to find wire insulation faults without a visual exam? Home Builder Home Repair 6 March 12th 04 03:17 PM
Is it possible to find wire insulation faults without a visual exam? Home Builder Home Ownership 6 March 12th 04 03:17 PM
Best possible insulation for 2x4 walls? _firstname_@lr_dot_los-gatos_dot_ca.us Home Ownership 4 January 24th 04 12:40 PM
Fixing loft boarding *through* insulation and derating cable. Mike Hall UK diy 11 January 9th 04 04:45 PM


All times are GMT +1. The time now is 11:59 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"