Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Fuse repeatedly blowing on potterton Boiler Clock/Programmer
Hello All,
I'm a bit of a diy n00b, but I can at least change a fuse. So I felt a bit foolish paying a central heating engineer £65 to get my heating re-started when the problem turned out to by a dead 3amp fuse in the mains socket that the boiler programmer (Potterton EP2001) was connected too. However since he first visited in late December I have since woken up on three separate mornings to find the house cold, and fuse blown again. Can anyone advise as to what is likely to be the cause of the fuses blowing? J |
#2
|
|||
|
|||
In an earlier contribution to this discussion,
jumblemo wrote: Hello All, I'm a bit of a diy n00b, but I can at least change a fuse. So I felt a bit foolish paying a central heating engineer £65 to get my heating re-started when the problem turned out to by a dead 3amp fuse in the mains socket that the boiler programmer (Potterton EP2001) was connected too. However since he first visited in late December I have since woken up on three separate mornings to find the house cold, and fuse blown again. Can anyone advise as to what is likely to be the cause of the fuses blowing? J You have an intermittent short circuit somewhere in your heating equipment or wiring. I would start by looking at the pump - 'cos that's where water and electrics come closest to each other. -- Cheers, Set Square ______ Please reply to newsgroup. Reply address is invalid. |
#3
|
|||
|
|||
"jumblemo" wrote in message ... Hello All, I'm a bit of a diy n00b, but I can at least change a fuse. So I felt a bit foolish paying a central heating engineer £65 to get my heating re-started when the problem turned out to by a dead 3amp fuse in the mains socket that the boiler programmer (Potterton EP2001) was connected too. However since he first visited in late December I have since woken up on three separate mornings to find the house cold, and fuse blown again. Can anyone advise as to what is likely to be the cause of the fuses blowing? J An intermittent fault somewhere in the electrical system. How long does the fuse normally last after you replace it? |
#4
|
|||
|
|||
I would think that the fan and the heating pump are the only high load
items. Mine just cost me for a fan although the fuse never blew. The unit just would not fire-up at all. |
#5
|
|||
|
|||
In message , jumblemo
writes Hello All, I'm a bit of a diy n00b, but I can at least change a fuse. So I felt a bit foolish paying a central heating engineer £65 to get my heating re-started when the problem turned out to by a dead 3amp fuse in the mains socket that the boiler programmer (Potterton EP2001) was connected too. However since he first visited in late December I have since woken up on three separate mornings to find the house cold, and fuse blown again. Well, it's unlikely to be the programmer Possibly the pump, maybe the fan Of course, if you'd mentioned the model of boiler, further advice might have been possible -- geoff |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Problem with Potterton Netaheat Electronic boiler -- clicks madly and refuses to start | UK diy | |||
Baxi WM 381 RS Boiler Blowing Fuse | UK diy | |||
Near death boiler + replacing a boiler | UK diy | |||
Central Heating problem - 2A fuse blowing in honeywell wiring box | UK diy |