UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
dave L
 
Posts: n/a
Default using 30A cable to supply 5A lighting circuit: good idea?

HI,

I decommissioned my electric shower so there is nothing attached to
that 30A circuit. I want to add a load of lights to the master
bedroom/ensuite which will (at full load) overload the exsting 5A
lighting circuit. I can't add a new circuit to the consumer unit,
plus the cables exiting the consumer unit are chased in to the plaster
which I don't want to rip out.

Is there a good reason not to connect my new lights to the
currently-unused 30A cable? Should I change the 30A fusewire for 5A
if I do connect them? IE, have 5A fusewire connecting to some 30A
cable which connects to 5A cable which supplies approx 1kw max load of
lighting.

Also if in the future I upgrade my fusewire consumer unit to one with
MCBs will any decent sparky (i'm wouldn't install the new CU ) refuse
to connect 30A cable to a 6A tripswitch?

Thanks a lot.
  #2   Report Post  
BigWallop
 
Posts: n/a
Default using 30A cable to supply 5A lighting circuit: good idea?


"dave L" wrote in message
m...
HI,

I decommissioned my electric shower so there is nothing attached to
that 30A circuit. I want to add a load of lights to the master
bedroom/ensuite which will (at full load) overload the exsting 5A
lighting circuit. I can't add a new circuit to the consumer unit,
plus the cables exiting the consumer unit are chased in to the plaster
which I don't want to rip out.


How much load are you thinking of taking to run lights ? There is nothing
stopping you from doing what you suggest, but you'd need to replace the
existing fuse with one marked at the new rating. To leave the fuse marked
as 30 amp, but to rewire it with a lower rated fuse wire, is not good
practice.

Is there a good reason not to connect my new lights to the
currently-unused 30A cable? Should I change the 30A fusewire for 5A
if I do connect them? IE, have 5A fusewire connecting to some 30A
cable which connects to 5A cable which supplies approx 1kw max load of
lighting.


When you find out by how much you'll need to run the new lights, then go for
the nearest rating to it. Remember though, that fuse wire only comes in
certain ratings, so you may find that the next one up is not really safe
enough to do the job properly, and you might need to place fused spurs in
line with you new lighting circuits for your own protection.

Also if in the future I upgrade my fusewire consumer unit to one with
MCBs will any decent sparky (i'm wouldn't install the new CU ) refuse
to connect 30A cable to a 6A tripswitch?

Thanks a lot.


A split load consumer unit is now the ideal way of distributing circuits
around the house. Power to sockets is taken from an RCD protected supply,
and lighting is taken from a similar set up as your existing box.


  #3   Report Post  
Roger Mills
 
Posts: n/a
Default using 30A cable to supply 5A lighting circuit: good idea?


"dave L" wrote in message
m...
HI,

I decommissioned my electric shower so there is nothing attached to
that 30A circuit. I want to add a load of lights to the master
bedroom/ensuite which will (at full load) overload the exsting 5A
lighting circuit. I can't add a new circuit to the consumer unit,
plus the cables exiting the consumer unit are chased in to the plaster
which I don't want to rip out.

Is there a good reason not to connect my new lights to the
currently-unused 30A cable? Should I change the 30A fusewire for 5A
if I do connect them? IE, have 5A fusewire connecting to some 30A
cable which connects to 5A cable which supplies approx 1kw max load of
lighting.

Also if in the future I upgrade my fusewire consumer unit to one with
MCBs will any decent sparky (i'm wouldn't install the new CU ) refuse
to connect 30A cable to a 6A tripswitch?

Thanks a lot.


I can't see a problem with what you want to do. The fuse must be the first
thing to go - so a 5a fuse with 30a cable is ok but a 30a fuse with 5a cable
definitely isn't. To avoid any future confusion, a prominent label on your
CU, stating that this is a 5a lighting circuit, wouldn't do any harm.

I have a similar situation - where a 45a cable was installed for an electric
shower, but in the event, we fitted a power shower (using stored hot water)
so the electrics only had to power the pump. We thus downrated the breaker
in the CU to 15a, but kept the heavy cable.

Roger


  #4   Report Post  
Frisket
 
Posts: n/a
Default using 30A cable to supply 5A lighting circuit: good idea?


"dave L" wrote in message
m...
HI,

I decommissioned my electric shower so there is nothing attached to
that 30A circuit. I want to add a load of lights to the master
bedroom/ensuite which will (at full load) overload the exsting 5A
lighting circuit. I can't add a new circuit to the consumer unit,
plus the cables exiting the consumer unit are chased in to the plaster
which I don't want to rip out.

Is there a good reason not to connect my new lights to the
currently-unused 30A cable? Should I change the 30A fusewire for 5A
if I do connect them? IE, have 5A fusewire connecting to some 30A
cable which connects to 5A cable which supplies approx 1kw max load of
lighting.

Also if in the future I upgrade my fusewire consumer unit to one with
MCBs will any decent sparky (i'm wouldn't install the new CU ) refuse
to connect 30A cable to a 6A tripswitch?

Thanks a lot.

As long as you de-rate the protection (ie. change the fuse to 5A) then
you're ok. You could run the whole lighting circuit in 6mm cable if it
floats your boat - and I'd happily connect it to a 6A breaker (and YES I'd
consider myself a decent sparky - my plumbing on the other hand...)
Regards, Richard


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Lighting Direct: A good company to do business with. parish UK diy 0 September 6th 03 10:35 PM
Is it a radial or ring circuit? Paul UK diy 14 September 4th 03 05:48 PM
Lighting circuit problems Turv UK diy 2 August 22nd 03 07:50 AM
Is it OK to put standard "twin & earth" cable directly into the cavity of a dwarf wall? Jon Weaver UK diy 20 August 8th 03 04:38 PM
Routeing Electrical FTE cable pickerel UK diy 3 July 24th 03 01:43 AM


All times are GMT +1. The time now is 07:40 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"